Buch, Englisch, 910 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 1700 g
ISBN: 978-0-87849-337-1
Verlag: Trans Tech Publications
Autoren/Hrsg.
Fachgebiete
Weitere Infos & Material
Preface
Committee
Construction and Structures
Lime Stabilization of Black Cotton Soil Using Bagasse Ash as Admixture
Durability-Based Appropriateness of Sawdust Concrete for Rigid Pavement
The Quality of Concrete Made with Typical Benin City Silty Sand
The Influence of Vibration Time and Sand Type on the Compressive Strength of Sandcrete Hollow Blocks
Accuracy of Static Differential GPS Techniques; Implications for Structural Deformation Monitoring
The Potential Use of Periwinkle Shell as Coarse Aggregate for Concrete
An Assessment of Torsional Parameters of Steel Reinforcement Used in the Nigerian Construction Industry
Electrical and Electronic Technology
Power Quality Assessment in a Distribution Network
Application of Particle Swarm Optimization Approach to Optimal Tuning of Load Frequency Controller
An Electronic Patient Record Management System Using Smart Cards
Application of Pareto Analysis to Faults Identification in Electrical Distribution Network: A Case Study of Ugbowo 11kV Feeder, Benin City, Nigeria
Differential Evolution Based Optimal Tuning of Load Frequency Controller
Design and Implementation of a GSM Activated Automobile Demobilizer with Identification Capability
Performance of Binary Phase Shift Keying (BPSK) and Quartenary Phase Shift Keying (QPSK) Signalling Schemes in Fast and Frequency Non-Selective Rayleigh Fading Channel with a Decision Feedback Equalizer (DFE) at the Receiver
Reduction of Fire Incidents due to Electrical Faults in Buildings
Analysis of Generating Capacity Dynamics of the Nigerian Power System between 1963 and 2020
Dielectric Strength, Breakdown Voltage and Acidity Test with Respect to Transformer Insulating Oil
Design and Parameter Estimation of a Three Phase Induction Motor Using a User-Interactive Computer Programme
Design, Construction and Performance Evaluation of a Low Cost Electric Arc Welding Machine
Comparative Analysis of Electric Field Measurement in Zaria
An Impact Assessment of the Nigerian Power Sector Reforms
Human Body Resistance and Temperature Measurement Device
An Investigation of Microwave Link Degradation due to Atmospheric Conditions (A Case Study of Akure-Owo Digital Microwave Link)
Investigation of the Characteristics of Radio Signal Propagation in Indoor Environment
Electricity Network Planning: The Key to Efficient and Reliable Power Supply to Consumers
An Experimental Autonomous Path Tracking Mobile Robot
Automatic Transfer and Controller System for Standby Power Generator
Food and Agricultural Technology
Leaching of Trace Metals from Two Different Size Soils
Dehydrated Cassava Chips Utilization in Starch and "Garri" Production
Determination of Cutting Resistance of Sugar Cane (Saccarum officinarum) Using a New-Type Test Machine
Development and Performance Evaluation of Rainwater Harvester for Drip Irrigation of Juvenile Citrus Orchard
Flapper Feed Device for Improved Productivity of Cassava Grater
Methods of Preserving and Improving the Quality of Locust Beans
Variations in Certain Climatic Parameters and Implications for Agricultural Production in Makurdi (Benue State), Nigeria
Development and Performance Evaluation of a Manually Operated Cowpea Thresher
Methods of Estimating Runoff and Soil Loss in Plots under Different Plant Densities of Amaranthus
Effects of Linear Alkyl Benzene Sulfonate Detergent on the Activity of Cassava Fermenting Enzyme
Field Comparison of Irrigation Scheduling of Tomato (Lycopersicon Esculentum)
Manufacturing Systems
Responsive Production Systems and Roles that Robots can Play
Application of Enterprise Modelling (EM) Principles to Improving the Performance of a Semi-Automated Production System
Materials Processing
Effects of Selected Media on Corrosion Behaviour of Mild Steel
Design of Compatibilizing Interfacial Polymer Layers Using a Macroinitiator
Rolling Temperature for Steel Hot Flat Rolled at Low Strain Rates
Network Structures, Flexibility and Stability in Thermal and Chemical Environments of Polyurethane Prepared from Rubber Seed Oil.
Studies in the Utilization of Biobased Additives as Thermal Stabilizer for Plasticized PVC
Evaluating Microstructural and Hardness Variations in Time Dependent Multipass Welded Mild Steel
Effect of Base Material on the Pore Size Distribution and Surface Area of Activated Carbon
Permeability Characteristics and Classification of Coal Seams in Nigeria
Effect of Particle Sizes on the Reinforcing Properties of Locally Sourced Filler in Rubber Vulcanisate
Effect of Lubrication Additives on the Physical and Chemical Properties of Soyabean Oil
The Study of Biogeoavailability of Calcium in Ashaka Cement Industry Environs of North Eastern Zone of Nigeria
Effect of Pass Reduction on Rolling Parameters Using Reverse Sandwich Model Integrated into the Hot Rolling Bland and Ford’s Theory
Determination of Optimum Welding Flux Composition Using the Bend Strength Test Technique
The Dependence on Temperature of Carbonization and Chemical Activation on Characteristics of Granular Activated Carbon Characteristics
Effects of Preservative Agents on Cassava Starch Adhesives
Oil and Gas
Maximizing Generated Energy Usage through Combined Cycle Cogeneration
Pressure Derivative Studies of a Laterally Infinite Reservoir with a Horizontal Well
Pressure Derivative Behavior of Two-Layered Reservoir with Vertical Wells
Geoinformation for Oil Spill Disaster Management in the Niger Delta Region of Nigeria
Assessing the Rate of Remediation of Polycyclic Aromatic Hydrocarbon Contaminated Soil Using Redox Parameters
Influence of Gamma Radiation on the Radiofrequency Dielectric Properties of Nigerian Crude Oil
Toxicity Assessment of some Crude Oil Contaminated Soils in the Niger Delta
Developing a Managed Pressure Drilling Strategy for Casing Drilling Operations
Sand Production Forecasts for Unconsolidated Gas Reservoirs
A New Correlation for the Viscosity of Natural Gas
Equations for the Z-Factor and Compressibility of Nigerian Natural Gas
Renewable Energy
The Role of Renewable Energy in the Electricity Industry in Zimbabwe
Enhancing the Output Characteristics of a Photovoltaic Position Sensor Using a Feed-Forward Neural Network
Application of Wind and Small Hydro Energy Sources for Rural Electric Power Supply in Nigeria
Analysis of Fish Fillet Drying Rates under Three Solar Energy Drying Systems
Development of an Energy Efficient Solid Fuel for Maximum Emission-Reduction and Regular Heating Rate in Fired Heaters
Optimal Utilization of Solar Arrays: Design and Implimentation of a Motorised Solar Energy Photovoltaic Array System
Optimum Seeking Position Control of Solar Collectors
Development of a Photovoltaic Powered Forced Convection Solar Dryer
Systems Design and Analysis
Designing Architect’s Brief for a Faculty of Engineering
Development of a New Product Using Two Distributed Teams
Maintenance Productivity Measurement: Case Study of a Manufacturing Company
System Potential-Based Productivity Evaluation Model
Evaluating Solution Methods to Bicriteria Scheduling Problems
Evaluation and Improvement of Dvorak Keyboard Layout Using CADWORK
Computer Aided Raw Material Requirement Planning (CARMRP) for Job Shop: A Case Study
A Study of Urban Traffic Management- A Case Study of Lagos State Traffic Management Authority
Investigation of the Vibrational Mode of a Long Bone – The Ulna
Surface Roughness Optimization of some Machining Parameters in Turning Operations Using Taguchi Method
Development of a Model for Analysing Forging Process
Development of a Model for Analysing Radial Flow of Slightly Compressible Fluids
Finite Element Simulation of Performance Characteristics of Infinitely Wide Plane Pad Slider Bearing
Tools, Machines and Equipment
Mathematical Modeling of a New Improved Design of a Rail Carriage Suspension System for the Wagons Used in Zimbabwe
Development of Software Package in Designing Chain Drives as Engineering Transmission Element
Risering of a Four-Cavity Die Production Mould by Convectional Method
Design and Manufacture of Palm Nut/Fibre Separator
Design for Manufacture of a Miniature Batch Reactor
The Effect of Baffles in Shell and Tube Heat Exchangers
Computerised Design Approach to a Sub-Press Mould for Composite Materials Manufacture
Quality Characteristics of Basic Hand Tools Sold in Nigeria
Waste Technology
Design, Development and Performance of Palm Waste Briquette Stove for Domestic and Industrial Usage
Performance Evaluation of Palm Waste Screw Press Briquette Moulding Machine
Fuzzy Based Solid Waste Management Method
Sustaining the Rural Energy Demand through Biogas Technology
Indoor Smoke Emissions from Direct-Fires in Urban Households in Benin City Area of Midwestern Nigeria
Additives Effects of Cement and Silica Clay on the Thermophysical Properties of Sawdust
Batch Treatment of Palm Oil Mill Effluent
Solid Waste Crisis in Nigeria – A Case Study of the Constraint to Effective Private Sector Participation (PSP) on Solid Waste Management in Lagos Metropolis
Improved Sawdust Briquette: An Alternative Source of Fuel
Bio-Treatment of Brewery Effluent Using Enzymes
Water Engineering
Drinking Water Quality Monitoring in Ado-Ekiti and Environs
Modelling of Sediment Transport Capacities of Ogbese and Owena Rivers in S.W. Nigeria
Use of Hydraulic Network Model for Evaluating Fire Flow Capacity of a Water Distribution Network
Bio-Treatment of Crude Oil Polluted Water Using Mixed Microbial Populations of P. Aureginosa, Penicillium Notatum, E. Coli and Aspergillus Niger
