Semi-Solid Processing of Alloys and Composites XIII

Selected, peer reviewed papers from the 13th International Conference on Semi-Solid Processing of Alloys and Composites (S2P 2014), September 15-17, 2014, Muscat, Sultanate of Oman
Erscheinungsjahr 2015
ISBN: 978-3-03835-220-4
Verlag: Trans Tech Publications

Buch, Englisch, 542 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 1060 g

Collection of selected, peer reviewed papers from the 13th International Conference on Semi-Solid Processing of Alloys and Composites (S2P 2014), September 15-17, 2014, Muscat, Sultanate of Oman. The 68 papers are grouped as follows: Chapter 1: Material Development and Characterisation, Chapter 2: Rheology, Modelling and Simulation,Chapter 3: Process Development, Chapter 4: Industrial Application

Autoren/Hrsg.

Modigell, Michael

Fachgebiete

• Technische Wissenschaften Maschinenbau | Werkstoffkunde Technische Mechanik | Werkstoffkunde Elastizität, Plastizität, Rheologie
• Technische Wissenschaften Maschinenbau | Werkstoffkunde Technische Mechanik | Werkstoffkunde Materialwissenschaft: Verbundwerkstoffe
• Technische Wissenschaften Maschinenbau | Werkstoffkunde Technische Mechanik | Werkstoffkunde Materialwissenschaft: Metallische Werkstoffe
• Technische Wissenschaften Verfahrenstechnik | Chemieingenieurwesen | Biotechnologie Metallurgie
• Technische Wissenschaften Maschinenbau | Werkstoffkunde Produktionstechnik Fertigungstechnik

Inhaltsverzeichnis

Preface, Committees and Sponsors
Chapter 1: Material Development and Characterisation
Semisolid Processing of Magnesium Alloys: Microstructure - Property Relationship
Preparation of Globular Microstructure in H18 Steel for Semi Solid Processing with the Use of Boron Addition

In Situ Microstructure Observation of Steel Grades in the Semi-Solid State for Thixoforging Process by Using Confoncal Laser Scanning Microscopy
A Comparison of Grain Refinement Efficiency by Shearing above and below the Liquidus
Microstructural Evolution of 7050 Aluminum Alloy Semisolid Billets Fabricated by RAP Process
Effect of Manganese on the Fe-Rich Phases in Al-22Si-2Fe Alloy by Cooling Slope
Effect of Casting Size on Microstructure and Mechanical Properties of Thixocastings
Effects of Post Heat Treatment on Microstructure and Mechanical Properties of RAP-Processed Cr-V-Mo Steel
The Mechanical Properties of Rheo-High Pressure Die Cast Al-Mg-Si-(Cu) 6xxx Series Alloys
Influence of Microstructural Inhomogeneity on Fracture Behaviour in SSM-HPDC Al-Si-Cu-Fe Component with Low Si Content
Aluminum Segregation in ZA27 Rheocast Alloy
Morphological Evolution of SCN Crystals in a Shear Flow
Effects of Cu on the Microstructures and Tensile Properties of Thixoformed Al-Si Alloys
Microstructural Evolution of Semi-Solid Type 304 Stainless Steel Deformed Severely by ECAP
Morphological Evolution of Al-2wt%Si-2.5wt%Cu Alloy Produced by EMS and EMS Enhanced by ECAP
Wear Properties of Al-17Si Alloys with Variable Fe Levels Formed by Semi-Solid Process
Chapter 2: Rheology, Modelling and Simulation
Squeeze Flow of Thixotropic Semisolid Slurries
Thermomechanical Modelling and Simulation of C38 Thixoextrusion Steel
Rheological Behavior of Semisolid Hypoeutectic Cast Iron Alloyed to Chromium
Experimental Study and Numerical Simulation on the Blistering Defect during Thixocasting
Semi-Solid Forging Process and Die Design in the Production of Aluminum Thin Plates
Semi-Solid Metal Processing: "Unlimited" Flow Velocity without Turbulence in Thin Cast Sections
Semisolid Metals: A Suspension with Non-Newtonian Liquid Matrix
Solidification of a Binary Solution (NH4Cl+H2O) under Shear Flow: A Numerical Study
Analysis by Micromechanical Modeling on Material Flow under Rapid Compression in the Semi-Solid State
Modelling of Extrusion Process for Aluminium A356 Alloy
Deformation Characteristics and Mechanism of Martensitic Stainless Steel during Thixoforming
Simulation on Flexible Thixo-Extrusion of Variable Cross-Section Part Based on DEFORM-3D Software
3D Numerical and Experimental Investigation on Semi-Solid AlSi9Mg Alloy Slurry Prepared by Electromagnetic Stirring
Simulation on the Thixocasting Process of the Turbocharger Impellers and Selection of the Viscosity Models
Chapter 3: Process Development
Effect of the Rheocasting Process and of the SLS Layer on the Fatigue Behavior of 357 Aluminum Alloy
Unconventional Microstructures in Tool Steel Obtained by Semi-Solid Processing and Subsequent Heat Treatment
The Research on the Annulus Electromagnetic Stirring for Preparing the Semisolid A356 Aluminum Alloy Slurry
Anodising of Aluminium Alloy Plates from Different Series Produced by Rheo-High Pressure Die Casting
Study on Refining Mechanism of Primary Si in Semi-Solid Al-25%Si Alloy Slurry Prepared by Rotating-Rod Induced Nucleation
The Solution Heat Treatment of Rheo-High Pressure Die Cast Al-Mg-Si-(Cu) 6xxx Series Alloys
Continuous Production of a Multi-Filament Reinforced Metal Matrix Composite Strip from the Semisolid State
Study of Defect Formation during Solution Treatment of 319S Thixocast Turbo Impellers
Investigation of Parameters Promoting Hot Cracking during Semi-Solid Forming Processes
Production of Aluminum/SiC/NiAl2O4 MMCs by Thixoforming of Recycled Chips
THINCASTTM; Providing Strong, Lightweight Castings for Automobiles and Other Applications
A Study on Bubbles in Semisolid Alloys
Semi-Solid Die Casting of Al-25%Si
Influence of Process Parameters on Surface Appearance and Roughness of a Low Si Containing Al-Alloy, in Semisolid Casting
Steels with High Temperature Carbides - New Possibilities for Semi-Solid State Processing
Comparison of Microstructure and Mechanical Properties of Semi-Solid Castings Produced Using Billets Made by EMS and SEED
The Refinement Mechanism of La-Ce Binary Alloy on Primary a Phase in A356 Alloy under Electromagnetic Stirring
Analysis of a Thixo-Lateral Forged Spindle from LTT C45, LTT C38 and LTT 100Cr6 Steel Grades
Semi-Solid Joining of D2 Cold-Work Tool Steel
Development of New Type Semi-Solid Injection Process for Magnesium Alloy
From Hot Forging to Thixoforging: FEM Analysis of Thixoforging Process for Steering Piston Production
Tooling Materials and Solutions for Thixoforming Steel: A Key to the Process Industrialization
Effect of Hot Rolling and Equal-Channel Angular Pressing on Generation of Globular Microstructure in Semi-Solid Mg-3%Zn Alloy
New Semisolid Casting of an Al-25Wt.% Mg2Si Composite Using Vibrating Cooling Slope
Effect of Semi-Solid Processing on Iron-Bearing Intermetallic Compounds in A380 Aluminum Alloy
Fracture Property Correlation of Rheocast (EMS) and Thixocast 6061 Aluminium Alloy
Effects of Inclined Plate Angle and Length on Semi-Solid Microstructure of Martensitic Stainless Steel
Effect of Rolling-Remelting SIMA Process on Semi-Solid Microstructure of ZCuSn10 Alloy
Using Semi-Solid Extrusion for the Production of Aluminum-Nanocomposite Master Alloys
Grain Refining through Semisolid Processing
Squeeze Casting of Semi-Solid A356 Alloy
Comparison between Prediction of Liquid Fraction versus Temperature and Experimental Results from DSC and SPSC
A New Technology to Improve the Elongation of A356 Alloy
Microstructure and Property of Rheo-Diecasting Magnesium-Alloy with Forced Convection Mixing Process
Hypereutectic Al-Si Alloy Tube with Gradient Structure Produced by Rheo-Squeeze Casting
Chapter 4: Industrial Application
New Generation of Brake Callipers to Improve Competitiveness and Energy Savings in Very High Performance Cars
SSM Provides Important Advantages; So, why has SSM Failed to Achieve Greater Market Share?
Industrial Applications for Aluminum Semi-Solid Castings