Nicoara / Opris | Advanced Materials and Structures V | Buch | 978-3-03835-212-9 | sack.de

Buch, Englisch, 346 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 740 g

Nicoara / Opris

Advanced Materials and Structures V

Selected, peer reviewed papers from the Fifth International Conference on Advanced Materials and Structures (AMS 2013), 24-25 October 2013, Timisoara, Romania
Erscheinungsjahr 2014
ISBN: 978-3-03835-212-9
Verlag: Trans Tech Publications

Selected, peer reviewed papers from the Fifth International Conference on Advanced Materials and Structures (AMS 2013), 24-25 October 2013, Timisoara, Romania

Buch, Englisch, 346 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 740 g

ISBN: 978-3-03835-212-9
Verlag: Trans Tech Publications


Collection of selected, peer reviewed papers from the Fifth International Conference on Advanced Materials and Structures (AMS 2013), 24-25 October 2013, Timisoara, Romania. Volume is indexed by Thomson Reuters CPCI-S (WoS).The 56 papers are grouped as follows: Chapter 1: Advanced Materials, Chapter 2: Materials Characterization, Chapter 3: Modern Processing Techniques
Nicoara / Opris Advanced Materials and Structures V jetzt bestellen!

Weitere Infos & Material


Preface, Committees and Sponsor
Chapter 1: Advanced Materials
About Replacement of Nickel as Amorphization Element for Fabrication of Ultra-Rapidly Solidified Ti-Zr Alloys
The Effect of Mo and Al on the Corrosion Behavior of Titanium and Some of its Alloys for Biomedical Applications
Structural Characteristics of Ductile Iron at Different Rare Earth Contribution from a Magnesium Ferrosilicon Alloy
Correlation between Microstructure and Magnetic Properties on MnZn Ferrite with Bi2O3 Increasing Addition
Composite Powder and Compacts of Iron/Iron Oxide Type Produced by Mechanosynthesis and Reactive Sintering
Crystallization of Ni-Cr-Si-B and Ni-Cr-Fe-Si-B Amorphous Alloys
Implant Surface Finishing Influence on Tissue-Implant Anchoring
Mechanical Behavior of Fe60Co14Ga2P10B5Si3Al3C3 Bulk Metallic Glass
The Influence of Sulphur and Oxigen Additions in Mg-Treated Iron on the Cooling Curves Parameters
Research on the Influence of Pelleting Mixture Components on Chemical Components and Pellets Structure
Chapter 2: Materials Characterization
Joint Quality Assessment of Three Different Laser Welded Dental Alloys
Description of Degradation Process of Rubberized Lean Concrete
Influence of Cooling Rate on the Structural Characteristics of Ca and Rare Earth Inoculated, Low-S Grey Cast Iron
Influence of the Si-Content on the High Temperature Oxidation Behaviour of NiCrBSi-Coatings
A Study on Metal-Ceramic Thermal Expansion Compatibility
An Evaluation of Sn-Cu-Ga and Sn-Cu-Ag Solder Alloys for Applications within the Electronics Industry
Analysis of Hazards Identified within the Premises of the Electric Steelworks, to Carry out the Risk Assessment
Computation of HAZ Hardness for Low Alloyed Welded Steels Using Five-Parameter Logistic Function
Damage Detection in Flux Cored Wire Welded Structures by Using Vibration Testing
Determination of Flexural Properties of Rigid PUR Foams Using Digital Image Correlation
Effects of Silicon Carbide Proportion and Artificial Aging Parameters on Microstructure and Hardness of Al-Cu/SiCp Composites
Experimental and Numerical Investigations of TBC Behaviour after Aging, Subjected to Tension and Bending
Determination of Mechanical Properties of Chondrocytes in Articular Cartilage Using Atomic Force Microscopy
Heat Transfer in Composites Subjected to Temperature Variations
Influence of Milling Time on the Homogeneity of the Al2O3/Ni Composite Powders Obtained by Mechanical Milling
Measurement of Young’s Modulus and Shear Modulus of Some Structures Welded Using Flux Cored Wire by Vibration Tests
Mechanical Effects of Simulated Pressure and Temperature Conditions on Porcelain Dental Bridges
Preparation and Characterization of Amorphous Soft Magnetic FeSiB Powders and Spark Plasma Sintered Compacts
Research about Relation between the Microstructures and Mechanical Properties of Metal Coating Layers
Research on Microstructure and Properties of the Active Surface of Bimetallic Tools for Plastic Deformation at Hot or Cold
Sample Preparation and HR-TEM Investigation Techniques of Ti Based, Ga Containing, Amorphous Alloys
Stainless Steel Brackets: In Vitro Corrosion Behaviour and Mechanical Debonding Test
Study of Superelastic Behavior of CuAlBe Shape Memory Alloy by Neutron Diffraction
Nodular Inhomogeneous Graphitization – Determining Factor of Fatigue Failure
The Synthesis and Characterization of PVA-Ketoprofen Cryogel, Biomaterial with Extended Drug Release Properties for Cartilage Replacement
The Effect of Laser Shock Processing on Corrosion Resistance of Stainless Steel AISI 316L
The Influence of the Sintering Temperature on the Wear Testing for Some Steels Samples Obtained by Powder Metallurgy
Wear Behaviour of New CoCrMoTi Dental Alloys
Wear Particle Analysis, the Result of Tribological Phenomena of Biomaterials Couplings-Ultra Hight Molecular Weight Polyethylene and Magnesium Aluminosilicate Ceramic
Chapter 3: Modern Processing Techniques
Fabrication and Test of High-Temperature Ceramic Transformer
Metallic Biomaterials Processing Technologies in Order to Obtain a New Design for a Hip Prosthesis Femoral Component
Nanocrystalline/Nanosized Mixed Nickel-Manganese Ferrites Obtained by Mechanical Milling
Open Cell Al-Si Foams by a Sintering and Dissolution Process
Optimizing the Parameters of Reactive Sintering for In Situ Fabrication of Al-Al2O3 Composites
Properties and Microstructure of HVOF Thermally Sprayed Carbide Based Coatings
Research on Increasing the Nitrogen Removal Efficiency by Changing the Secondary Treatment Parameters
Researches Regarding the Improvement of the Steel Quality
Smart Mobile Workstation Used to Transmit Data for Non-Destructive Testing of Pipelines Welded Joints
Synthesis of the Fe-10%Si Nanocrystalline Powder by Mechanical Alloying
Welding of AA2124/SiC/25p-T4 by FSW at High Welding Speed and Monitoring the Process by Real-Time Control of Infrared Termography and Energy Consumption
Aluminium High Speed Drilling - Some Technological Aspects
Experimental Research on Modern Methods of Welding Pipelines Using Base Materials X60 and X70
Edge Fillet Laser Welding of AISI 304 Stainless Steel
An Axiomatic Design View on Part Orientation Schemes
Influence of the Electric Field Voltage on the Microhardness of the Layers Coated by Thermal Spraying
Integration of CAD CAM Techniques in the Development of an Injection Mould for Automotive Parts


Ihre Fragen, Wünsche oder Anmerkungen
Vorname*
Nachname*
Ihre E-Mail-Adresse*
Kundennr.
Ihre Nachricht*
Lediglich mit * gekennzeichnete Felder sind Pflichtfelder.
Wenn Sie die im Kontaktformular eingegebenen Daten durch Klick auf den nachfolgenden Button übersenden, erklären Sie sich damit einverstanden, dass wir Ihr Angaben für die Beantwortung Ihrer Anfrage verwenden. Selbstverständlich werden Ihre Daten vertraulich behandelt und nicht an Dritte weitergegeben. Sie können der Verwendung Ihrer Daten jederzeit widersprechen. Das Datenhandling bei Sack Fachmedien erklären wir Ihnen in unserer Datenschutzerklärung.