Sonstiges, Englisch, Band Volume 223, 870 Seiten, Format (B × H): 125 mm x 142 mm, Gewicht: 200 g
Reihe: Advanced Materials Research
Sonstiges, Englisch, Band Volume 223, 870 Seiten, Format (B × H): 125 mm x 142 mm, Gewicht: 200 g
Reihe: Advanced Materials Research
ISBN: 978-3-03785-096-1
Verlag: Trans Tech Publications
The modelling of Machining Operations has become very widespread today, with many researchers developing models with which to predict metal-cutting performance. The aim here is to provide an answer to the challenges presented by the machining industry, which is presently facing very tight economical and environmental constraints. The collection of over 100 peer-reviewed papers covers twelve research topics, including: ?Analytical and Numerical Modelling?; ?Cutting Fundamentals: Input Parameters?; ?Cutting Fundamentals: Experimental Validation?; ?Surface Integrity?; ?Surface Topography?; ?Tool Wear and Tool Life?; ?Dynamics and Stability?; ?High-Speed Machining and 5-Axes Machining?; ?Abrasive Machining?; ?Ultra-Precision and Micromachining?; ?Computer-Aided Manufacturing (CAM)?; ?Experimental: Non-Conventional Machining?. This work will thus constitute an invaluable handbook on the subject.
Autoren/Hrsg.
Fachgebiete
Weitere Infos & Material
A Lagrangian FEM Model to Produce Saw-Toothed Macro-Chip and to Study the Depth of Cut Influence on its Formation in Orthogonal Cutting of Ti6Al4V3D Modelling and Simulation of Gun DrillingInvestigation of the Machining Behavior of Metal Matrix Composites (MMC) Using Chip Formation SimulationComputational Study of Ultrasonically-Assisted Turning of Ti AlloysSimulation of Multiple Chip Formation when Broaching SAE 5120 Low Alloy Steel3D-FEM Modeling of Gear Skiving to Investigate Kinematics and Chip Formation MechanismsPredictive Modeling for Distortion in Large, Thin-Walled Machined ComponentsModeling of Cutting Process with Cutter Axis InclinationCutting Forces Modeling in Finish Turning of Inconel 718 Alloy with Round InsertsReal-Time Cutting Force Prediction and Cutting Force Coefficient Determination during Machining ProcessesAn Analytical Thermomechanical Modelling of Peripheral Milling Process Using a Predictive Machining TheoryAnalytical Model of Chip Formation in Case of Orthogonal Cutting ProcessesCFRP Drilling Model: Fiber Orientation Influence on Mechanical Load and DelaminationNumerical Model for Prediction of Cutting Force in Peripheral Milling Process Including Thrust and Tangential DampingFEM Based Design of a Chip Breaker for the Machining with PCD Tools3D FEM Model for the Prediction of Chip BreakageA Numerical and Experimental Investigation of the Deformation Zones and the Corresponding Cutting Forces in Orthogonal CuttingOn Methodologies inside Two Different Commercial Codes to Simulate the Cutting OperationApplication of the Nodal Integrated Finite Element Method to Cutting: a Preliminary Comparison with the ?Traditional? FEM ApproachValidation of Finite Element Modeling of Drilling Processes with Solid Tooling in MetalsCoating-Substrate-Simulation with an Advanced Adaptive Finite Element CodeVirtual Reality Animation of Chip Formation during TurningEnergy Efficient Process Planning Based on Numerical SimulationsSimulation of the Temperature Distribution in NC-Milled WorkpiecesNumerical Prediction of the Interface Temperature Using Updated Finite Difference ApproachEffect of Cutting Conditions on Temperature Generated in Drilling Process: a FEA ApproachAnalysis of Forces and Temperatures in Conventional and Ultrasonically-Assisted Cutting of BoneInput Data for the Numerical Simulation of Metal CuttingInverse Flow Stress Calculation for Machining ProcessesInverse Identification of Johnson-Cook Material Parameters from Machining SimulationsNew Thermal Issues on the Modelling of Tool-Workpiece Interaction: Application to Dry Cutting of AISI 1045 SteelFinite-Element Simulations of Split Hopkinson Test of Ti-Based AlloyThe Numerical Investigation of Stress Distribution on the Rake Face for Grooved Cutting Tool InsertsCalibration of the Rheological Model Considering the Temperature in Milling Operation of Ti-6Al-4V: a Preliminary AnalysisDeformation and Microstructure in MachiningStrain Rate Effect on the Mechanical Behavior of Austenitic Stainless Steel during MachiningTechnological and Environmental Aspects in Milling of ?-TiAlEvaluation of the Cutting Force and Geometric Error for Roughing Operation by Plunge MillingA Metal Cutting Approach to Investigate the Tribological Properties of Nano Crystalline Boric Acid and the Effect of its Carrying MediumModeling the Process-Induced Modifications of the Microstructure of Work Piece Surface Zones in Cutting ProcessesAnalytical and Numerical Modeling of Strain Hardening in AISI 304 Steel CuttingA Hybrid Approach to Predict Residual Stresses Induced by Ball-End Tool Finishing Milling of a Bainitic SteelPrediction of Machining Induced Surface Integrity Using Elastic-Viscoplastic Simulations and Temperature-Dependent Flow Softening Material Models in Titanium and Nickel-Based Alloys3D Numerical Prediction of Residual Stresses in Turning of 15-5PHPrediction of Residual Stresses in Turning of Inconel 718Residual Stress Prediction by Means of 3D FEM SimulationAnalysis of Surface Integrity in Dry and Cryogenic Machining of AZ31B Mg AlloysInfluence of Worn Tool on Polishability and Wear Resistance of VP20ISO Mold SteelHigh-Speed Milling Characteristics and the Residual Stresses Control Methods Analysis of Thin-Walled PartsInfluence of Hard and Soft Inclusions on the Machinability and Polishability of VP100 Mold SteelAnalysis of Surface Integrity for DIN 100Cr6 Steel Conical Bearing Rings after Hard TurningSurface Integrity Functional Analysis in Hard Turning AISI 8620 Case Hardened Steel through 3D Topographical MeasurementModeling and Characterization of Surface Structures Produced by MillingIdentification of Surface Generation Mechanisms Based on Process Feed-Back and Decomposition of Feed MarksModulation-Assisted Machining: A New Paradigm in Material Removal ProcessesTool Load during Multi-Flank Chip FormationDevelopment of a Simulation Model to Investigate Tool Wear in Ti-6Al-4V Alloy MachiningModeling and Optimization of Multiple Characteristics in the AISI 52100 Hardened Steel TurningLife Prediction of Cutting Tool by the Workpiece Cutting ConditionAn XPS Study of the Stratified Built-up Layers Developed onto the Tool Surface in the Dry Drilling of Ti AlloysExperimental Design Applied to the Machining of Windows Cage Ball Joints Homokinetic SAE 8620 Steel with CBN ToolAnalysis of Sintering Parameters by SPS on Cemented CarbideDynamic Study of Thin Wall Part TurningStability Analysis of Machining with Spindle Speed VariationInvestigating Dynamics of Machine Tool Spindles under Operational ConditionsFixed Boundaries Receptance Coupling Substructure Analysis for Tool Point Dynamics PredictionA Novel Approach to Thin-Wall Machining of Aerospace Structures - Stability Margin Prediction Using a New Damping Modelling ApproachThe Influence of Process Machine Interactions on the Stability of Parallel MillingModeling the Varying Dynamics of Thin-Walled Aerospace Structures for Fixture Design Using Genetic AlgorithmsFEA-Methodology for the Prediction of Aluminium Thin Walled Part Deformation in Dry Milling OperationsModeling and Analysis Effects of Material Removal on Machining Dynamics in Milling of Thin-Walled WorkpieceA New Experimental Setup and Method to Analyze Cutting Forces in Non-Stationary Conditions5-Axis Flank Milling Tool Path Smoothing Based on Kinematical Behaviour AnalysisModeling Cutting Forces for Five Axis Milling of Sculptured SurfacesMechanistic Model Based on the Actual Removal Volume during Simultaneous Five-Axis MillingOptimization of High Speed Machine Tool FramesFEM-Based Simulation of Temperature in Speed Stroke Grinding with 3D Transient Moving Heat SourcesModeling and Simulation of Phase Transformation during GrindingModeling of a Polishing Tool to Simulate Material RemovalFinite Element Simulation of Quick ? Stop Experiments for Better Understanding of Chip Formation in GrindingOptimization of Process Parameters in CFRP Machining with Diamond Abrasive CuttersTheoretical and Experimental Determination of Geometry Deviation in Continuous Path Controlled OD Grinding ProcessesKinematic Model for Ultrasonic-Assisted Manufacturing of Bore Holes with Undefined Cutting EdgesMachinability Evaluation in the Ultrasonic Drilling (USD) Process of Aluminum Oxide-based CeramicsFEM Simulation of Strain Rate in High Speed GrindingEvaluation of Quality of Steering Systems Using the Honing Process and Surface Response MethodologyStudy on the Simulation Model and High-Speed Characteristics of Cylindrical GrindingModelling of Ultra-Precision Turning Processes in Consideration of UnbalancesSimulation Model for Micro-Milling Operations and Surface GenerationEffects of the Cutting Tool Edge Radius on the Stability Lobes in Micro-MillingAn Experimental Study on Dynamics and Stability of Miniature End MillsInvestigation on Surface Finishing of Components Ground with Lapping Kinematics: Lapgrinding ProcessInterest of Multiphysics and Multilevel Simulation Approaches to Enhance the Machining ProcessSimulation of Serrated End Milling Using Solid Modeling TechniquesOptimization of Non-Cutting Tool PathsOptimization of the 2 1/2 D Pocket Machining Using Multiple ToolsSurface Quality of Cavities Obtained by EDM ProcessDevelopment of a Prototype of Electrochemical MachiningInfluence of Correlation between Electrical Discharge Machining Parameters with the Formation of Surface Defect?s in Products Machined by EDMFinite Element Modeling of Microstructural Changes in Hard Turning
