Materials Engineering and Technologies for Production and Processing II

Erscheinungsjahr 2016
ISBN: 978-3-03835-793-3
Verlag: Trans Tech Publications

Buch, Englisch, 768 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 1420 g

This edition published by results of International Conference on Industrial Engineering (ICIE-2016, May 19-20, 2016, Chelyabinsk, Russian Federation). In the issue are collected scientific papers from area of materials engineering and technologies for materials production and processing in the different areas of modern manufacturing. This collection will be useful for wide range of engineers and scientists from different areas of engineering knowledges.

Autoren/Hrsg.

Radionov, Andrey A.

Mikhailov, G.G.

Vinnik, Denis

Fachgebiete

• Technische Wissenschaften Maschinenbau | Werkstoffkunde Produktionstechnik
• Technische Wissenschaften Maschinenbau | Werkstoffkunde Technische Mechanik | Werkstoffkunde

Inhaltsverzeichnis

Preface, Conference Committee
Chapter 1: Functional and Special Structural Materials, Technologies of Coatings, Strengthening and Hardening
Magnesium Dry Mixes for Outer Wall Decoration
Research the Properties of Temperature High-Coercivity Permanent Magnets NdFeB
Justification of the Choice Matrix Material of the Magnetoactive Elastomer for Working Camera-Channel Peristaltic Unit
Process Engineering of Dimensional Fused Silica Etching
Amorphous Copper-Based Alloys: Structure, Technology and Properties
Increasing Corrosion Properties of Steel 04Cr25Ni6NMo3
Mathematical Model of Nanostructure Formation in Binary Alloys at Electron Beam Treatment
Nanostructured Strengthening of Springs and Spring Steels
Application Features of the Cutting Tool, Hardened by Laser Pulsed Radiation
Titanium-Containing Composite Sorbent-Photocatalyst Based on Calcium Silicates and Aluminosilicates
Evolution of Macro-Scale Plastic Flow Localization of Tri-Layered Stainless Steel - Low Carbon Steel - Stainless Steel Metal with Digital Image Correlation Method
Barium Hexaferrite Single Crystal Growth Using PbO and Na2O Based Flux
Experimental Study of Ba7Fe4O13, Ba3Fe2O6, Ba2Fe2O5, BaFe2O4 Barium Ferrites
Microcrystalline and Amorphous Photovoltaic Silicon Materials Performance Optimization
Corrosion-Resistance of MAO-Coatings on Al-Si Alloys
Analysis of Electrodynamics Properties of Materials with High Dispersity Metal Powder in Axial Moving Systems
Study of Thermal Resistance and Mechanical Properties of Thin Sheets of Low-Alloyed Aluminum Al-Cu-Mn and Al-Mg-Si Alloys
The Influence of Electromagnatic Field Microwave on Physical and Mechanical Characteristics of CFRP (Carbon Fiber Reinforced Polymer) Structural
Phase Equilibria in the Copper-Rich Corner of the Cu-Ni-Si-Cr System
Synthesis of Multilayer Vacuum Ion-Plasma Coatings Ti-Tin during the Surface Modification
Comparative Analysis of Catalytic Activity in Complex NiO-CuO-Fe2O3-Cr2O3 Oxide System of Different Production Technologies
Modification of Nanostructured Maraging Steels Surface with Atmospheric Nitrogen at Steel Hardening in Confined Space
Thermal Diffusion Galvanizing in Ferriferous Zinc Powder
The Structure of Carbon Nanotube Exohedral Complexes with Lithium in a Wide Range of Concentrations
Peculiarities of Forming of the Wear-Resistant Cast Iron Coating Structure on Steel 45 upon Plasma-Powder Surfacing
Hardening Process by Complex Local Deformation Investigation
Metallographic Examination of Forming Improved Mechanical Properties via Surfacing of Steel HARDOX 450 with Flux Cored Wire
Foamer Influence on the Foam Concrete Properties Obtained in the High-Speed Foam Generator
Effect of the High-Heating on the Chemical and Phase Composition of the Al-Ni-Cr Layered Coatings
Development of Resource-Saving Cellular Glass Technology and Materials Based on it
Heat Treatment of Wear Resistant Steels for Mud Pumps
Superplastic Behavior of an Al-Cu-Mg-Mn-Ag Alloy
Use of Mathematical Modeling in Building Ceramics Functional Properties Studies
Pore-Forming Additives for Ceramic Gravel Production Made of Technogenic Materials
Analysis of Physico-Mechanical Properties of Composites Based on Polylactide and Thermally Modified Wood Fibers
Investigation of Relationship between Structural and Crystallographic Condition of some Constructional Materials and their Mechanical Properties
The Structure and Phase Composition of the Diffusion Zone in a Titanium and Steel Composite
Work Softening and Low Cycle Fatigue of Molybdenum Alloy under Force-Controlled Loading and Elevated Temperatures
FE Analysis of the Applicability of the Shear-Compression Testing to the Modeling of the Asymmetric Rolling Process
The Impact of Explosion Welding Parameters on Al/Cu Laminated Composites Interface
Investigation of the Diffusion Processes at the Interface of the Cu/Ti Metal Composite
The Study of the Dissolution AlZr2 Ligatures in the Liquid Alloy AlMg6Mn1
Tin and Nickel Influence on the Structure and Properties of the Leaded Bronze Obtained by Means of the Centrifugal Casting
Dislocation Structure Evolution during Plastic Deformation of Low-Carbon Steel
Hot Deformation of Martensitic and Supermartensitic Stainless Steels
The Effect of Aluminum Oxide Additives on the Phase Equilibrium in Borosilicate Systems and Crystallization of Borosilicate Melts
Plating Technology for Contact Joint Performance Improvement in Electrical Equipment
Experimental Study of Contact Joint Characteristics in Electrical Equipment
Experimental Study and Thermodynamic Modeling of Phase Equilibria in the PbO-Fe2O3 System
Determination Features of the Component Diffusion Coefficients of the Fe-Cr-Ni-Gr Powder Systems Sintering
Determination of Suitable Binder Grade According to the Superpave Mix Design Method for Southern Russia
Auger and X-Ray Photoelectron Spectroscopy Study of the Tribocontact Surface after Laser Modification
The Formation and Functioning of Surface Nanostructures at Tribocontact
Gas Atomization of the Liquid 82N7HSR Nickel Base Alloy to Produce Micropowder for Additive and Coating Technologies
The Manufacturing of the AlSi12-Al2O3 Composite Powder for Additive Production Methods
The Study of the Contact Angle of Silicon Carbide High-Carbon Iron Melt
Magnetic and Microstructure Study of Thin Films of FeCuNbMoSiB FINEMET Alloy
Calculation of the Amount of the Reduction Required for the Formation of Compound Layers during Cold Rolling of Bimetals
Application of Ion-Plasma Coatings with Low Droplet Phase Content
The Effect of the Cast High-Manganese Steel Primary Structure on its Properties
Use of the Electric Steel Melting Slag in Production of the Expanded Clay Gravel
The Study of Aging Cold Rolled and Hot Dip Galvanized Automotive Steel
Electropulse Machining of Metals
Opening Wave Strain Strengthening
Synthesis of Transition Metals Carbide Compounds in the Vacuum Arc Discharge Plasma
Increasing the Intensity of Cementation Process of Tool Low-Alloy Steels by Surface Laser Treatment
Gear Wheels Surface Engineering by Deformation Hardening and Carburization
Peculiarities of Thermal Hardening of Experimental Sparingly-Alloy Tool-Class Steels
Modern Methods and Technological Solutions for Effective Processing of Gear Wheels
Formation and Structure of Diffusional Zinc Coatings Formed in Nanocrystallized Zinc Powders
Kinetic Description of (Cr, Fe)7C3 Carbide Dissolution in Austenite of High-Carbon Fe-Cr-C Ternary Alloys
Plasma-Electrolytic Treatment as an Innovative and Resource-Saving Technology of Metal Surface Treatment
X-Ray Microanalysis of Hardmetal Powder, Produced by Electroerosion Dispersion of VK8 Alloy in Kerosene Environment
Chapter 2: Innovative Technologies in Metallurgy Industry and Materials Processing
Investigation of the Surface Layer Structure of High-Chromium and High-Strength Steels at the Variation of the Heating Temperature
SHS Ferroaluminum Obtained from the Disperse Waste of Engineering
Changing the Arc Efficiency during Melting of a Charge in Arc Steel Melting Furnaces
Energy Reduction Technologies Based on the Lubricant Supply in the Roll Contact System "Quarto" during the Hot Strip Rolling
Technology of Packing Materials for Metal Products
Effect of Stress-Strain State during Combined Deformation on Microstructure Evolution of High Carbon Steel Wire
Determination of the Basic Parameters of the Recovery Process for Extracting Iron from Iron and Steel Slag
Experimental Investigation of Al-Alloy Directional Solidification in Pulsed Electromagnetic Field
The Study of the Fluoroapatite of the Fine Coal Yuzhno-Yakut Basin
Influence of the Microstructure Al-12%Si Alloy on the Properties of the Oxide Layer Formed with MAO
Neural Network Modeling of Coefficient of Burden Resistance to the Gas Movement in the Lower Part of the Blast Furnace in Conditions of Operation with Coke Nut
On Advanced Recycling Technology for Cutting Fluid and Waste Oils Produced at the Metallurgical Enterprises
Structure Investigation of the Constructional Steel St3ps after Argon-Arc Plasma Treatment
Efficiency Improvement of Sintering as a Result of Surface-Active Substance Use in Pelletizing at the JSC "Ural Steel"
Calculation of Impeded Shrinkage Casting Processes in Sand Layer
Narrow Jet Plasma as the Energy Efficient and Safe Technology for Metal Cutting
Modeling of the High Temperature Creep and Rupture under the Complex Stress State
Liquid-Phase Recovery of the Metallurgical Slag Using Induction Heating Installation
Experimental Substantiation of a Method of Improving the Efficiency of Ultrasonic Drilling of Small Diameter Holes
Solution to the Diffusion Problem in the Thermocyclic Nitrocementation of Steel
Interaction of Hydrogen Atoms with Vacancies and Divacancies in bcc Iron
Estimation of the Heat Stability of Hardened Cr-V Cast Irons
Applying Thermal Coatings to Narrow Walls of the Continuous-Casting Molds
Electropulse Processing of Gold-Bearing Ore
Mathematical Modeling of Mechanized Technologies Soldering
Carbon in Solidphase Red

Über Autor(innen)

Eds. A.A. Radionov, G.G. Mikhailov, D.A. Vinnik