Sonstiges, Englisch, Band Volumes 84-85, 820 Seiten, Format (B × H): 125 mm x 142 mm, Gewicht: 200 g
Sonstiges, Englisch, Band Volumes 84-85, 820 Seiten, Format (B × H): 125 mm x 142 mm, Gewicht: 200 g
Reihe: Applied Mechanics and Materials
ISBN: 978-3-03795-049-4
Verlag: Trans Tech Publications
The aim of this special volume was to facilitate the exchange of information on the best practices for Sustainable Power, Sustainable Materials, Green Manufacturing Technology and Applications, etc. It provides an opportunity for engineers and scientists, in academia, industry and government, to address the most innovative research and development ideas, including technical challenges, social and economic issues, and to discuss ideas, results, work-in-progress and experience concerning all aspects of Green Power, Materials and Manufacturing Technology and Applications. The work offers the reader a wealth of ideas.
Autoren/Hrsg.
Fachgebiete
- Technische Wissenschaften Maschinenbau | Werkstoffkunde Technische Mechanik | Werkstoffkunde
- Technische Wissenschaften Energietechnik | Elektrotechnik Alternative und erneuerbare Energien
- Technische Wissenschaften Maschinenbau | Werkstoffkunde Produktionstechnik Fertigungstechnik
- Technische Wissenschaften Technik Allgemein Nachhaltigkeit, Grüne Technologien
Weitere Infos & Material
Research on the Multidisciplinary Optimization Design Method for the Diesel EngineApproach Toward Parametric Design of Typical Parts and Parts-Library Based on UGDesign and Study of Gate-Type Steel-Shuttering Jumbo for Tunnel Lining Based on CAD/CAEMDO of the Transmission System Based Collaborative OptimizationThe Development of Physique Monitoring CAD System Based on RBF Neural NetworksThe Design of SVM-Based Fitness Consulting CAD SystemThe Exploration of Fuzzy Inference-Based Fitness Monitoring CAD SystemThe Influence of Green TherapyCuring Kinetics of Octaepoxysilsesquioxane/MNA SystemStructure and Properties of Regenerated Cellulose Film with Fluorocarbon CoatingEffect of Sintering Temperature on Microstructure of Porous Materials Using Iron Tailing and ShaleEffect of Zr Content on Properties of Mg-Zr PM Damping AlloysPreparation of Corundum/Mullite Composites by SinteringSynthesis of Ultrafine Long Afterglow Phosphor with High Brightness via Al2O3 Coating RouteAnalyzing Relationship between Genetic, Geographical Factors and Protein Content of Winter Wheat at Different Regional ScalesExperimental Research of the Anodic Bonding in the Si-Glass-Si 3-Layer StructureInfluence of Depositing Parameters on Microstructure of Ni-Co Pulse PlatingFine Particle Dispersion and Deposition in Three Different Square Pore Flow StructuresSome Research on the Medical MaterialsConcrete Property Analysis with the Perspective of ?5-10-14-18? and ?5-10-18-22? Band GradationThe Application of Multi-Agent Technology in the Fault Diagnosis System of Motor ArmatureMultivariate Statistical Process Monitoring and Fault Diagnosis Based on an Integration Method of PCA-ICA and CSMA Secondary Development System on Grader Working Device Oriented to Mechanism OptimizationT-S Fuzzy Control for Maximum Power Point Tracking of Solar Power Generation SystemsResearch of Single Granule and Granule Group Motion Model by DEMModeling and Simulation of Hydraulic AGC System in a Cold MillThe Research on CNC Machine Tool?s Position Limit Protection Equipments Based on Negative Logic ControlThe Application of the Baseline and Monitoring Methodologies to the Renewable Energy for Base Stations ProjectRoll Damping and Anti-Capsizing System for Ships Using Fuzzy-Extension Control StrategyModelling and Simulation of Phased Array Transducers Base on Advanced UT TechniquesBuilding New Reliable Wireless Network by Using Distributed ControlThe Research on H2 Optimal Control Applied to Active Vibration IsolationResearch on New Machining Method that Cutting Arc Surfaces in SIEMENS840D SystemPrediction of Compressive Strength of Aerated Lightweight Aggregate Concrete by Artificial Neural NetworkActive Vibration Control for Lathe Based Neural NetworkInfluence of Structural Parameters on Mechanical Properties of Double-Block Ballastless TrackCollision-Free Trajectory Generation for Waterway Surfaces of a PDC Drill BitEffect of Impact Position and Initial Velocity on Structure of Collided TankerExperimental Research on Mechanical Calculation of Fascine Object?s Underwater FallingThe Harmonic Response Analysis on Vibration System of Disc Vibration DryerParticle Swarm Optimization Based Dimension Synthesis of the Experimental Mechanism for Elastic Bungee Jumping RopesIncipient Hydrate Formation Pressure-Temperature and Equilibrium Composition for CH4-N2-O2-THF-H2O SystemThe High Stress Soft Coal Seam Face Prediction Sensitive Index Critical Value ResearchApplication and Advance in Super-Hard Tool MaterialEnvironmental Characteristical Study on Pyrite Smelting SlagStudy on Hydrological Simulation of Jin River Based on SWAT-X ModelNumerical Simulation of the Mechanically Pumped Two-Phase Cooling LoopInvestigation on the Heat Exchange Characteristics of the Condenser for Space ApplicationsExperimental Investigation on the Accumulator Liquid Distribution of Mechanically Pumped Cooling SystemImpact of Different Film-Cooling Modes at Trailing Edge on the Aerodynamic Performance of Heavy Duty Gas Turbine CascadeEnvironmental Activity of Heavy Metals in Slags Treated by Electrokinetic Removal TechnologyReformed Hydrous-Ethanol Application in Spark Ignition EngineNumerical Simulation of Furnace Combustion Characteristic in HTACNumerical Simulation of Natural Convection Heat Transfer on Microencapsulated PCM SlurriesReadout Circuit for Uncooled Pyroelectric IRFPAOptimum Design of Multi-Axle Trailer?s Steering Mechanism Based on ADAMSDiscussion on the Design of a New Type Down-Hole BOPMechanism Implementation for a 4WID/4WIS Unmanned VehicleOptimal DFIG Converter Protection Design under Different ControllersA Material Selection Model of Mechanical Products Based on Total Life Cycle DesignRecent Nanofabrication of Silicon Dioxide on Silicon Wafer Using AFM Operated at Low TemperatureDesign of Material Electrostatic Test PlatformThe Design of Multi-Index System on UCAC2 CatalogThe Design of Automatic Rotary-Rivet-Placing SystemCalculation and Analysis of Microstructure of Austenitic Steel for Supercritical UnitDevelopment for the Optimization Technique of the Coiling Tension in Degreasing UnitA New Type of Pig Handling TrolleyMachining Accuracy Analysis and Error Compensation Approach with the Effects of Cutting Tool Tip?s Radius in NC Lathe Machining ProcessImprovement and Implementation of Numerically-Controlled Process for Edger Mill StandOptimization and Realization of Bridge Girder of 320/50t-22m Quenching CraneResearch on Structural Parameters of Conical NozzleIntelligent Prediction on the Quality of CementingStudy on Roller Eccentricity Compensation in a Cold MillStudy on Soft Zone of Type 420 Stainless Steel Weldment during the Induction Brazing ProcessResearch on Machining Methods of Turning Trapezoidal Thread for Slender Axle on LatheOptimum KOH Wet Etching of Cantilever Tip for Better Image Captured by NanoeducatorAnalysis of Milling Forces in Slot Milling of Aluminum Alloy with Three Flutes CutterApplication of Intelligent Data Mining Method for Traffic ForecastingResearch on Signal Timing Method of Intersection Based on RFIDRapid Design of Low-Voltage Motor Protector Based on Axiomatic TheoryComputer Modeling for the CFG Pile in Highway Soft FoundationNumerical Simulation of NO Conversion in the N2/O2/NO by Dielectric Barrier DischargeInvestigation of Annealing Effect on the Electrical and Optical Properties of ITO Film Prepared by Sol-Gel ProcessThe Design of Double Liquid Zoom Lens? Model Based on Electrowetting EffectStudy on Fault Signal Detection for PMLSMApplication Design of CAN Bus (CANOpen) for Rotary Screen Printing MachineExperiment Platform Design cSPACE-Based for a Permanent Magnet Linear Synchronous Motor Driven Inverted PendulumDigital Filter Design in Power?s Harmonic Wave DetectionAcquisition and Analysis on 3D Deformation of Windshield Glass in Vehicle-Pedestrian AccidentStudy on the Current Application Situation and Development of E-Portfolio Based on ICT for Mechanical Components Using Genetic AlgorithmsA Study of the Microstructure and Hardness of Ti-5Al-2Sn-2Zr-4Mo-4Cr by Laser Shock PeeningStudy on Intensified Bioleaching Technology by Static Magnetic Field of Chalcopyrite TailingsInfluence of Mo/Sb Co-Doping on Scintillation Properties of PbWO4 CrystalPreparation and Properties of Polyvinyl Alcohol (PVA)/Polyvinyl Pyrrolidone (PVP) HydrogelPreparation of Activated Alumina AdmixtureHigh Efficient White-Phosphorescence PLEDs by Using Water/Alcohol-Soluble Polyelectrolyte as an Electron Injection LayerStudy on the Hydrolytic Stability of Borate EsterPreparation and Photocatalytic Activity of Laden SiO2/TiO2 Composite PhotocatalystModification of Polishing Putty: A Study on Inorganic FillerThe Research of Silica-Coated Chromium Oxide Green Pigment Prepared by Liquid Phase MethodOctaepoxysilsesquioxane Cured by Different Curing AgentsDrive Spindle Simulation for Continuous RollingA Preliminary Investigation on Friction Stir Spot Welding of Steel/MgStudy on the Tribological Properties of Porous UHMWPEResearch on Noise Generation Mechanism of Rubber Material for Water-Lubricated BearingsRecent Progress of Vibration Analysis on Fault Diagnosis for Rolling BearingEffect of Substrate Conditions on Residual Stress of Plasma-Spraying Sm2Zr2O7 Thermal Barrier CoatingsReal-Time Reliability Analysis and Optimal Distribution of the Reliability on Five-Axis Machining CenterVisual Inspection on Premature Failure of Electric Motor BearingsFinite Element Thermo Analysis of Friction Material Enhanced by Bamboo FiberResearch on Magnetic Properties of Nd2Fe14B/a-Fe/Nd2Fe14B Exchange-Coupled Trilayer FilmsTwo-Photon Excitation Fluorescence Lifetime Imaging Based on Time-Correlated Single Photon CountingA Control System for Traffic Light Based on GPRSChemical Sensors Based on Fiber Bragg GratingMonitoring of Microorganisms Growth Process Based on Fiber Bragg Grating Biosensor1064 nm High-Power Broad Area Semiconductor Lasers with Electrode PatternHigh Performance 785 nm Wavelength Super-Luminescent DiodesResearch of Angled 8? Integrated 808 nm Wavelength SLDs808 nm Semiconductor Lasers with Tailored Gain for Mode ShapeInfluence of Gain Dispersion on the Propagation Characteristics of Ultrashort Optical Pulses in Distributed Fiber AmplifiersHigh Performance Precast Wall Panels with Shear Transfer Provided by Carbon Fiber GridThe Study on the Electrolyte Behavior of Aromatic Polyesters from Diphenolic Acid and Isophthaloyl ChlorideEffect of Sol-Gel Method for Medium Steel Phosphating Coating of Electrochemical BehaviorEnhanced Electrokinetic Removal of Heavy Metals in MSWI Fly Ash Assisted by Cation Exchange MembranesPechini Sol-Gel Fabrication and Luminescent Properties of Lu2SiO5: Ln3+ (Ln=Tb,Ce) Thin FilmsThe Effect of Silver Ion Catalysis on Bioleaching of Chalcopyrite TailingsThe Viscosity Measurement of Polyethylene Glycol DilaurateFirst Principle Investigation of O2 Adsorption on the LaMnO3 (001) SurfaceAn Analysis on Technology and Product Quality Effect of II-Powdery Emulsion ExplosivesThe Application of Air-Space with Mixed Emulsion Explosive in Open-Pit MinesModification of Asphalt by MontmorilloniteRefrigerant Capacity and Magnetocaloric Effect on LaFe11.1Co0.8Si1.1BX AlloysEffects of Mg Substitution on the Thermoelectric Properties of Ca3Co4O9-Based MaterialsCalculation and Analysis on PM Thermal Characteristics Influence Performance of PMSM Based on FEMThe Trend Change of Bitumen Research: A Text Mining Analysis (2000-2010)Design and Experimental Research of Solar Powered Water Pump System Based on Single ChipMarine Growth Effect on the Vibration Characteristics of Offshore Wind Turbine with Jacket FoundationComputer Simulation of Icing on NACA0015 Blade Airfoil for Vertical Axis Wind TurbineNumerical Simulation on the Static Torque Performance of Vertical Axis Wind Turbine with Different Blade AirfoilsAn Improved Differential Evolution Algorithm for Dynamic Economic Dispatch of Power SystemsOptimal Design of the Vibration Device of Block Making MachineAnalysis on Proportion and Development of Steel Workers? Hospitalization CostsAnalysis of Steel Industry Workers Abridged Life TableIntegrated Automation Monitoring System in the Application of 220kV SubstationApplication of GM (1, N) Model on Slope Stability Analysis in Open Pit MineResearch on Energy Consumption of Screw Compressor under Load/UnloadAnalysis of Energy Consumption Efficiency Based on DEA-TobitThe Design of a Central Air Conditioning System for a Rebuilt Commercial BuildingAnalysis of Total Factor Energy Efficiency of Manufacturing Industry in Shandong Province Based on Malmquist Index Empirical StudyStudy on Power Load Forecasting Base on Grey Prediction Model by Slip Average MethodResearch on Implementation Strategies of Green Supply Chain ManagementStudy on Green Supply Chain Management Based on Circular EconomyDecoupling Analysis of Economic Growth and Total Primary Energy Supply for the BRICS: 1971-2008Comparative Study on Carbon Emission and Energy Consumption of the Textile Industry in Henan Province
