Sonstiges, Englisch, Band Volume 857, 638 Seiten, Format (B × H): 125 mm x 142 mm, Gewicht: 200 g
Reihe: Materials Science Forum
Sonstiges, Englisch, Band Volume 857, 638 Seiten, Format (B × H): 125 mm x 142 mm, Gewicht: 200 g
Reihe: Materials Science Forum
ISBN: 978-3-0357-2020-4
Verlag: Trans Tech Publications
Autoren/Hrsg.
Fachgebiete
Weitere Infos & Material
Intermetallic Study on the Modified Sn-3.5Ag-1.0Cu-1.0Zn Lead Free SolderSolderability and Interfacial Intermetallic Compound (IMC) Growth of Sn-Cu-Ni Solder with Additions of GermaniumThe Effects of Zinc Addition on the Microstructure, Melting Point and Microhardness of Sn-0.7Cu Lead-Free Solder Fabricated via Powder Metallurgy MethodProperties of Aluminum Matrix Composite (AMCs) for Electronic PackagingEffects of Wetting Behavior on Gallium Addition in In-Zn Solder AlloyThe Alloying and Aging Effects on the Wettability and Intermetallic Bonding of the Sn-Zn-Cu-Bi Soldering Alloy on a Cu SubstrateNanoindentation Study on Heat Treated Gold Wire BondingDirectional Growth Behaviour of Intermetallic Compound of Sn3.0Ag0.5Cu/ImSn Subjected to Thermal CyclingNanoindentation of Sn3.0Ag0.5Cu/ENIG Solder Joint after High Temperature StorageSolidification of Sn-3Ag-0.5Cu and Sn-0.7Cu-0.05Ni SoldersEffects of Trace Phosphorus in Sn-Cu-Ni Wave Solder DrossSuppression of Cu3Sn with Ni in High Cu Containing Sn-Cu Solder AlloysPeritectic Reactions and Phase Transformations of Sn-30wt%Cu for High Temperature Pb-Free Soldering ApplicationsXPS Analysis of Oxide Films on Lead-Free Solders with Trace Additions of Germanium and GalliumImprovement of Sn-0.7Cu Lead Free Solder Joints on Shear Strength with Addition of Titanium Oxide (TiO2) ParticlesSurface Roughness and Wettability of SAC/CNT Lead Free SolderWettability of CNT-Doped Solder under Isothermal AgingMechanical Interlocking on Leadframe Surface for Bondability of Au Wedge BondUltrasonic Vibration in Leadframe for the Bondability for Au Wedge BondWettability of Soldering Alloys at Heating by Electron BeamMechanical and Electrical Properties of Carbon Nanotubes Based Isotropic Conductive AdhesivesEffect of Loading Amount of Glucose Precursor on Mesoporous Carbon Surface Area for Supercapacitor Electrode ApplicationEffect of Al Excess on the Band Structure of ZnO Using Density Functional TheoryMicrowave Irradiation Assisted Synthesis of Silicon Carbide NanotubesCharacterization of Silicon Carbide Nanowhiskers Synthesized by Microwave Heating Using Photoluminescence Spectroscopy and Fourier Transform Infrared SpectroscopySynthesis of Silicon Carbide Nanowhiskers from Graphite and Silica of Different Ratio by Microwave Irradiation Assisted SynthesisEffect of Stoichiometry and Sintering Temperature on the Mechanical Properties of Zinc Ferrite (ZnxFe3-xO4)p-Type Conductivity Control in ZnO Films Grown by Molecular-Beam EpitaxySynthesis and Characterization of Ni0.8Zn0.2Fe2O4 Nanoparticles by Self-Combustion TechniqueSynthesis of Chlorophyll Thin Film from Noni Leaves via Dip Coating ProcessProperties of Y3Fe5O12 (YIG) as Nanocatalyst for Ammonia Formation Produced from Magnetic Induction Method (MIM)Response Surface Methodology (RSM) in Fabrication of Nanostructured SiliconRigid Polyurethane Foam with Ionic Liquid Modified Multi Walled Carbon Nanotubes CompositesThe Effects of Trans-Polyoctylene Rubber (TOR) on the Cure Characteristics and Swelling Behaviour of Activated Carbon Filled Styrene Butadiene Rubber (SBR) VulcanizatesComposite Materials Characterization for Aircraft ApplicationThe Influence of Blending Methods in Epoxy/PMMA Polymer BlendDevelopment of Seamless Pipe Based on Al/Al2O3 Composite Produced by Stir Casting and Centrifugal CastingEffects of Composition and Fe on the Liquid Phase Sintered W-Brass CompositesPalm Kernel Shell Filled Recycled High-Density Polyethylene: Effect of Filler LoadingControl of Temperature in Cutting Zone in Machining of Alloyed Case-Hardened Steels by Applying a Ceramic Tool with Wear-Resistant CoatingsComparative Evaluation of Properties of Various Tool Materials by Area of Indentation Track in Pendulum Scratch TestingEdge Cutting Tools for Machining of Hard-to-Cut MaterialsSpecifics of Application of Cutting Ceramics with Functional Coating in Turning of High-Strength MaterialsInfluence of Tool Rotational Speed on the Mechanical Properties of Friction Stir Welded Al-Cu-Li AlloyEffect of Sensitization Treatment on Corrosion Properties in Austenitic Stainless Steel 304Synthesis of Porous Anodic Alumina (PAA) on Aluminum Alloy AA6061 in Mixture of Phosphoric Acid and Oxalic AcidThe Effect of Sintering Temperature to the Microstructure of PM F75 (Co-Cr-Mo) AlloyTwo-Step Solution Heat Treatment of AlSiCu Alloy for Improvement of Mechanical PropertiesA New Free-Machining Steel Containing Bismuth and CalciumThe Effect of Solution Heat Treatment on Incipient Melting of Al2Cu Intermetallic Phase in Lightweight MaterialsAgeing Response of Powder Metallurgy AZ91 and AZ91 Reinforced with Multiwall Carbon NanotubeMicrostructure and Mechanical Properties of Friction Stir Welded AA2195-T0Thermal Aging of Dissimilar-Metal Weld Joints for Reactor Pressurized Vessels at Elevated TemperatureMicrostructural Evolution of Austenitic Stainless Steel AISI304 and AISI316 Subjected to High-Temperature Thermal AgingEffect of Concentration of Oxalic Acid on the Synthesis of Porous Anodic Alumina (PAA) on Aluminum Alloy AA6061Segregation Measurement of Inconel 718 Feedstocks Used in Low-Pressure Metal Injection MoldingPrecision Hole Making on Laminates Composite: Comparison between Drilling and PunchingDynamic Increase Factor of High Strength Concrete with Silica Fume at High Strain Rate LoadingExperimental Study on Internal RH of BFS Mortars at Early AgeStrength of Portland Cement with Several Composition of Bottom Ash in Different Fineness with Curing Time of 28 DaysThe Barriers and Strategies of Implementing the New Building Material (Fibre Cement Wall) in Malaysia Case Study: Aurum Synergy, Perlis, MalaysiaDolomite Quarry Waste as Sand Replacement in Sand BrickAn Experiment on Bond Properties of Reinforcements Embedded in Ultra High Performance ConcreteBond-Slip Relation of Pretensioned Concrete Members for Various Tensioning ForcesAssessment of Reinforced Concrete Building with Soil Structure Interaction Effect under Vertical EarthquakeThe Temperature Effect to the Concrete due to the Single Strike of High Electric CurrentIndoor Air Quality of Fired Clay Brick Incorporated with Mosaic SludgeLeachability of Heavy Metals from Steel Mill Sludge Incorporated in Fired Clay BrickLeaching of Heavy Metals Using TCLP and SPLP Method from Fired Clay Brick Incorporating with Mosaic SludgeProperties of Steel Mill Sludge Waste Incorporated in Fired Clay BrickExperimental Study of Slurry Infiltrated Fiber Reinforced ConcreteThe Chemical Composition and Fineness of Natural Cement at Different Raw Meal ProportionEffect of Chromium (II, III) Oxide and Cobalt Oxide on the Colour and Fineness of CementMechanical Properties of Volcanic Ash Based Geopolymer ConcretePotential of Geopolymer Mortar as Concrete Repairing MaterialsReview on Different Types of Geopolymer Concrete FibresEffect of Coal Ash Properties on Compressive Strength of Bottom Ash-Based Geopolymer ConcreteMicrostructure and Mechanical Properties of Ambiently-Cured Blended Coal Ash-Based Geopolymer ConcreteEffect of NaOH Concentration on Flexural Strength, Phase Formation and Microstructural Development of Kaolin Geopolymer CeramicEffect of Ultra High Molecular Weight Polyethylene (UHMWPE) as Binder and Sintering Temperature in Kaolin Geopolymer Ceramics on Flexural StrengthThe Use of Borax in Deterring Flash Setting of High Calcium Fly Ash Based GeopolymerSimulation Behavior of Flexure in Reinforced Concrete Beam with Opening Reinforced with Glass Fiber Reinforced Polymer (GFRP)Flexural Behaviour of Patch-Repair Material Made from Unsaturated Polyester Resin (UPR)-MortarOptical Data Support on Flexural Strength of Kaolin Coated Lumber Wood via Geopolymer TechnologyStudy on a Fractional Model of Filtration Effect of Cigarette Filter TipPreparation and Characterization of Chitosan/Alginate Polyelectrolyte Complex Prepared by Using Calcium Tripolyphosphate Ionic GelatorAnalysis on Fluid Characteristics in Y-Shape Bifurcate Coronary ArteryPerformance of Newly-Fabricated Modular Surface Plasmon Resonance (mSPR) SensorSimultaneous Saccharification and Co-Fermentation (SSCF) Using Banana and Pineapple Waste as SubstrateOptimization of Eugenol Ester Using Statistical Approach of Response Surface MethodologyFacile Synthesis of Activated Carbon from Swamp Taro Stalk via Single Step ZnCl2 ActivationSynthesis and Characterization of Biomass Supported Ag, Co and Ag-Co NanoparticlesDyeing of Nylon Fabric with Natural Dye from Cassia Fistula Fruit: A Research on Effect Metal Mordants ConcentrationDyeing Silk Fabric with Natural Dye from Longan Leaves Using Simultaneous Mordanting MethodDyeing Properties of Nylon Fabrics with Mangrove Bark Extract via Mordanting MethodsExtraction and Tensile Behavior of High Performance Hibiscus tiliceus FiberPrinting of Silk Fabric with Reactive Dye Using Flour of Wild Taro Corm as a Resist Printing PasteRemoval of Iron and Manganese Using Cascade Aerator and Limestone Roughing FilterCharacterization of Alum Crystals Synthesized from Waste Aluminium Beverage CansRemoval of Cadmium and Zinc Contaminations in Landfill Leachate by Using Electrocoagulation ProcessHot Solvent Extraction Method for Recycle Epoxy Resin in Waste Printed Circuit Board with Polyethylene GlycolKinetics and Isotherm Studies on Nd(III) Adsorption onto Xanthated ChitosanTin (Sn) Recovery from Wave Soldering Lead Free Solder Dross via Hydrochloric Acid Leaching and Combustion TreatmentRemoval of Iron (Fe) in Rice Husk via Citric Acid Leaching TreatmentAcid Treatment of Aluminium Dross: Properties and ApplicationLandslide Simulation Using Limit Equilibrium and Finite Element MethodCorrelation of Brillouin Stokes Signals and Optical-Signal-to-Noise-Ratio in Multi-Wavelength Brillouin Fiber Laser with Additional Fiber Bragg GratingMathematical Modelling of Stress-Strain State of Multilayer Shell MoldsTheoretical Prediction of Crack Formation in Axisymmetric Multilayer Shell MoldsStructure Characterization of Low Cost Fabricated Soft Material Built MicrochannelMaximal Predicable Time Scale of Gas Emission about Fully Mechanized Mining FaceNumerical Simulation of Pressure Loss in Largesize Annulus of Deepwater Drilling RiserThe Shielding Materials from EM Radiation for Aircraft FuselageSAC-OCDMA over Indoor Optical Wireless Communication (OWC) System Based on Zero Cross Correlation (ZCC) CodeOptimization of Output Coupling Ratio for Multi-Wavelength Brillouin Fiber Laser Employing FBG and DCF as Gain Medium
