Sonstiges, Englisch, Band Volumes 656-657, 828 Seiten, Format (B × H): 125 mm x 142 mm, Gewicht: 200 g
Reihe: Key Engineering Materials
Sonstiges, Englisch, Band Volumes 656-657, 828 Seiten, Format (B × H): 125 mm x 142 mm, Gewicht: 200 g
Reihe: Key Engineering Materials
ISBN: 978-3-03859-277-8
Verlag: Trans Tech Publications
The 132 papers are grouped as follows:
Chapter 1: Materials Research and its Applications;
Chapter 2: Material Processing Technologies;
Chapter 3: Applied Research in Materials Science;
Chapter 4: Applied Mechanics and Mechanical Technologies;
Chapter 5: Measurements and Monitoring
Autoren/Hrsg.
Fachgebiete
Weitere Infos & Material
A Dye Sensitized Solar Cell with ZnO-Coated TiO2 Electrode and Carbon Nanotubes Electrode for High Power Conversion EfficiencyInfluences of MOS Device Characteristic under Different Oxygen-Dose Participations in the Silicon SubstrateThe Estimation of the Mechanical Property of the Porous Material by Numerical AnalysisAcidic Treatment of CaO-Based Materials for Medium-High Temperature CO2 CaptureCharacterization of Novel Sorbents for Mercury Removal at Elevated TemperatureDevelopment of Recovery System for Extracting Silicon Carbide from Photovoltaic Industry Abrasive SlurryEffect of Added Cr3C2 on the Microstructure and Mechanical Properties of WC?SiC CeramicsEffect of Al Addition in Cast Nickel Base Superalloys, Inconel-738 on Microstructures and Oxidation Behaviors at 900?C and 1000?CEffect of Sintering Condition on the Microstructure and Electrical Properties of Lead-Free (Na0.5K0.5)NbO3 - Bi0.5(Na0.95K0.05)0.5TiO3 CeramicsElectroless Ni-P/Diamond/Graphene Composite Coatings and Characterization of their Wear and Corrosion Resistance in Sodium Chloride SolutionESD-Reliability Analysis and Strategy of the GaN-Based Light-Emitting DiodesEvaluation of Surface Properties and In Vitro Characterization of Surface Modified In Situ TiO2 NanofibersPreparation and Characterization of Protective LSM Coatings Produced by Atmospheric Plasma SprayingPreparation of Electroless Nickel-Phosphorous-TiO2 Composite Coating for Improvement of Wear and Stress Corrosion Cracking Resistance of AA7075 in 3.5% NaClPreparation of Nanocrystalline Cubic Boron Nitride Coating by Magnetron Sputtering MethodProduction Processes and Characteristics of Porous Alumina with Air Bubbles Introduced into SlurryThe Dependence of ECR-CVD Processing Parameters on Deposition Uniformity of Hydrogenated Amorphous Silicon (a-Si:H) FilmsThermodynamic Possibilities and Limits for Producer Gas Desulfurization and HCL Related Interferences for Zn, Mn, Ce and La Based Sorbents of Sulfur CompoundsThin-Film Growth Rate Monitor by Normal-Incidence ReflectanceEfficiency Analysis of Gas Turbine Combined-Cycle Fed with Synthetic Natural Gas (SNG) and Mixture of Syngas and SNGOptimization of Operating Conditions for an SOFC StackOscillation Phenomenon of the Cell Performance for an Anode-Supported Solid Oxide Fuel Cell with a Low-Porosity/High-Thickness Anode StructureRate Effects on Dynamic Properties of Liquid under NanoconfinementThe Thermal Image Analysis and Fuel Conversion Characteristics on Porous Media-Catalyst Hybrid Reactor in Dry Auto-Thermal ReformingViscosity Effects of Spray Characteristics in Air-Blast AtomizerA Numerical Simulation Study on Machining Performance for Front Face Circular Grooving Using Special Structure Milling Cutters ? Part 1: Simulation Method and Examination of Machining CapacityA Numerical Simulation Study on Machining Performance for Front Face Circular Grooving Using Special Structure Milling Cutters ? Part 2: Simulation Results and Discussions for Machining a Groove with Rectangular Sectional ProfileA Study on Tool Damage of Threading Tap in Screw Cutting of Stainless Steel 15-5PHAir Jet Assisted End Milling of Titanium Alloy Ti-6Al-4V ELI at High Cutting SpeedAssessment of Geometrical Deviations of Machined Part by Using Coordinate Measuring MachinesBasic Study on Thermo Chemical Turning Method for Metal Bonded Diamond WheelsCharacterization of Machining Damages Generated by a Piercing Process in CFRP LaminatesDamage of PVD-Coated Cutting Tools Due to Interrupted Cutting of Ni-Based SuperalloysA Novel Cutting Concept of CFRP Composites for Extending the Life of ToolDevelopment of the Local Polishing Technique for Single-Crystal SiC WaferEffect of Cutting Conditions on Tool Wear in Driven Rotary Cutting of Maraging SteelEffect of Cutting Force Control on Cutting Characteristics of CFRP in Diamond Saw CuttingEffect of Dry Ice Blasting on Removal of Loading Carbon Chips on Wheel SurfaceEffect of High-Pressure Coolant Supply on Chip-Breaking and Tool Wear in Machining of Stainless SteelEffect of Work Material?s Hardness on Cutting Performance of TiAlN- and CrAlN-Coated Cutting ToolsEffects of Cooling Conditions on Thermal Crack Initiation of Brittle Cutting Tools during Intermittent CuttingEffects of Cutting Fluid Application in the Performance of the Nimomic 80A TurningEffects of Guide Groove Shape on Chip Controllability for Chip-Guiding TurningEffects of Supplying Oil Mist and Water Mist with Cold Air on Cutting Force and Temperature in End Milling of Difficult-to-Cut MaterialsEstimating the Cutting Characteristics of Spiral Tap - Tool Edge Temperature and Fluctuation of Cutting ForcesEvaluation of Grinding Performance by Mechanical Properties of Super Abrasive Wheel - Evaluation of Grade by Grinding ForceEvaluation of Machining Forces in Asymmetrical Face Milling of Cast Iron DIN GGG50High Precision Turning of Hardened Steel by Use of PcBN Insert Sharpened with Short Pulse LaserHigh-Efficient Regeneration of Grinding Performance Using Adhesive Films in Dry Grinding of CarbonImproving the Polishing Effect of Stainless Tube by Magnetic Finishing with Gel AbrasiveInfluence of the Cutting Fluid on Tool Edge Temperature in End Milling of Titanium AlloyInfluence of Tool Wear on Cutting Characteristics in Ultra-Precision CuttingInvestigation of Machinability in Milling of Difficult-to-Cut Materials Using Water Soluble and Water Insoluble Cutting OilL-Shaped Machining of Anisotropic Woods with a Fine Wire Cutting ToolMachinability Evaluation of Inclined Planetary Motion Milling System for Difficult-to-Cut MaterialsMachine Learning of Cutting Conditions in Drilling Using Artificial Neural NetworkMachining Feasibility of a New Developed Medium in Electrical Discharge MachiningNear-Dry Machining of Titanium Alloy with MQL and Hybrid Mist SupplyShear Cutting Behaviors in Thermosetting and Thermoplatic CFRP LaminatesSimulation Analysis and In-Process Measurement of the Workpiece Temperature Distribution in Large Surface GrindingSize Effect in Machining on Initial Tool Wear in Heat-Resistant Alloy CuttingStability of Adhered Material to the Cutting Edge of a Cermet Insert in Turning of an Austenitic Stainless SteelStudy on Applicability of Large-Area EB Irradiation to Micro-DeburringStudy on Surface Characteristics of EDMed Surface with Nickel Powder Mixed FluidStudy on Ultrasonic Cavitation-Assisted Micro-Endmill MillingThe Effect of Eccentricity of the Tool on the Surface Morphology of FSJ JointThe Machinability of CFRP with Cutting Movement of End-MillingThe Research of FPGA-Based Short Current Protection for Micro Electrochemical MachiningTool Wear Characteristics in Near-Dry Cutting of Ni-Based SuperalloyWear Monitoring of Steel Ball of a CNC Machining Centre by Using Surface Roughness of Finished Test PiecesA Novel Tape and Diamond Process Developed for Polishing Hard SubstratesEffects of Filler Compositions on Mechanical and Physical Properties of the Dissimilar Resistance Spot Welded between Aluminium Alloy and Carbon SteelElectric Arc Furnace Dust Treatment Process by Iron PowderHeat Treatment and Mechanical Testing of AISI H11 SteelMechanical Properties Evaluation of Metal Components Repaired by Direct Metal LaminationSmoothing of GaN Substrate by Ultraviolet Assisted Polishing in KOH SolutionStudy of Electroplated Nickel Layer Thickness and Saw Parameters on Cutting Performance in Diamond Wire Sawing of Sapphire IngotsDesign of Rotoformer Mechanism and Cooling Steel - Conveyor in Sulfur Granulation SystemsEffects of Focusing Condition on Micro-Welding Characteristics of Borosilicate Glass by Picosecond Pulsed LaserGloss Evaluation of Hairline-Finished Metal Surface Using Patterned Area Illumination Method: Reproduction of Gloss Evaluation by Ray TracingInvestigation of Crack Generation in a Notch during Diameter-Enlargement Working Method ProcessingRecommendation of a Measure for Enhancing the Precision of Dimensions of Foil Products in Single Point Incremental Forming TechnologySimulation of Cracking Behavior in Planar Solid Oxide Fuel Cell during Thermal CyclingTensile Strength and Metallurgical Analysis in Anodized Al/Cu Joint Using Friction Stir WeldingViscous Dissipation Effects on the Coating Resin Flow Characteristics in High-Speed Optical Fiber Coating ProcessBehavior of MnS on Belag Formation and Observation on Carbide ToolDevelopment of a Computer Generation Holography for Generating Square Matrix Light Spots Applied to the Laser Patterning SystemNumerical Analysis for the Growth of Epitaxy Layer in a Large-Size MOCVD ReactorModelling of Granular Solid-Structure Interaction: A Comparative Study Using Conventional FEM Approach and Linked DEM-FEM ApproachSimulation of the Effective of Friction on the Deformation in Equal Channel Angular Pressing (ECAP)Simulation of Effective Stress and Temperature Field of the Die and Workpiece during ECAP of Pure Titanium at Different Ram Speeds by Finite Volume MethodA Parametric Study of Diesel Oxidation Catalyst Performance on CO Reduction in Diesel Dual Fuel Engine ExhaustApplication of Taguchi Method to Optimize the Operating Parameters for a Solid Oxide Fuel CellCombination of Au Dielectrophoresis Chip and Optical Tweezers for Cell CultureConcentration Gradient Effect on the Capturing Ratio of Nanopore for DNADevelopment of a Portable Optical Interferometry Microscope SystemNanopore Positive Pulse Detection of DNA with Salt GradientsKinetics of Microwave Vacuum Drying of ?Cat Chu? Mango in Mekong Delta - VietnamSwelling Behavior of Soft and Biological MaterialsA Novel Mechanical Design of Automatic Laser Target-Scoring SystemsA Double-Sided In-Plane Lateral Comb-Drive Actuator Fabricated by a Plaster-Based 3D-PrinterControlling Wrinkling and Flatness during the Processing of the Bend Section of a Pipe by Applying Vibration to the MandrelTheoretical Modeling and Fabrication of Two-Dimensional Microstructures by Using Micro-Anode-Guided Electroplating with Real-Time Image ProcessingAn Analysis of the Lubrication Characteristics of Mechanical Seals with Parallel Sealing Faces Using an Average Flow ModelAnalysis of Dynamic Contact and Carrying Capacity Factors for Super-Modulus Pinion and RackConcentrated Photovoltaic System with Multi-Curvature Fresnel ConcentratorConsideration of Interlock System Applicable to Pneumatic Driving Systems as the Safety System (BS/EN764-7)Design Calculation for Wedge Cam of Small Roller Centering Three-Jaw JigDesign of Shielding System for Impulse Ground Penetrating Radar ApplicationsDevelopment of Herringbon-Grooved Aerodynamic Journal Bearing Systems for Ultra-High-Speed RotationsDynamic Analysis of Offset Printing Press Gear-Cylinder-Bearing System under Time-Varying Meshing Stiffness EffectFault Diagnosis Research for Mine Fan Based on the CFDGradient Force of Electromagnetic Strength to Drive Precisely the Small MassImplementation and Validation of the Jet Flame Model Using C++ Open Source Codes Computational Fluid Dynamics SoftwareInvestigation of Optimum Assembly Tolerance for a Machine Tool SpindleInvestigations of Cylindrical and Conical Whirl Instabilities on Hydrodynamic Journal BearingsNon-Linear Analysis and Modeling of the Structure with Bolted JointsOptimization of Low-Noise and Large Air Volume Blower Based on Load CharacteristicResearch on Acoustic Radiation Characteristic for Cylindrical Structure with Elastic Plate Cap in Mid-Frequency RegionResearching and Calculating the Effect of the Slides and the Nozzles? Structural Positions of "Rice Sorting Machine?Testing and Improvement of Static Performance of Proximity Sensor for a Mobile RobotThe Data Combining Method and the Forming Control Algorithm from the 3D Scanning Machine and Processing in the SLS MachineThe Effects of High Pressure Gas Burner Parameters on Thermal Efficiency for 2014 International Conference on Machining, Materials and Mechanical Technology (IC3MT)The Point-Array Coupling Algorithm in 3D Scanning Machine by Laser RayThermal Conduction Measurement and Analysis for a Spaceborn SensorThermal-Structural Analysis for the Optimization of a Low Beam Projector Headlight DesignMicro-Hole Diameter Inspection Using Audible SoundOn the Development of Virtual Inner Loops for Feature RecognitionAccuracy of Three-Dimensional Shape Measurement Using a Triangulation Method Sensor with Optical SkidComprehensive Calibration of Structured Light Measurement System Using Planar ChessboardDesigning and Implementing the Remote-Environmental-Parameters-Monitoring-by-Internet KITOn the Development of Blend Faces and Holes Recognition Algorithm for CAE Applications
