Novel Trends in Production Devices and Systems III

Erscheinungsjahr 2016
ISBN: 978-3-03859-534-2
Verlag: Trans Tech Publications

Sonstiges, Englisch, Band Volume 862, 360 Seiten, Format (B × H): 125 mm x 142 mm, Gewicht: 200 g

Reihe: Materials Science Forum

Novel Trends in Production Devices and Systems III (NTPDS III) special volume is aimed at publishing scientific achievements in the fields of Materials Science and associated Production Technologies, as well as at enhancing the worldwide cooperation among young and senior academicians and/or practitioners, and specially those from the European region. The volume has been enriched taking into account years of research and teaching activities in the fields, experiences resulting from the scientific collaboration among higher education centers, e.g.: CECOL, while at the same time by also counting on a prestigious editorial review board that made strong analyses of the submitted papers. Some of the main topics included in the book are those related but not limited to the trends in Materials Science and their application in industry, e.g.: composites and polymers, materials weldability, analysis of metals and alloys, numerical analyses and simulation of materials, etc.

Autoren/Hrsg.

Delgado Sobrino, Daynier Rolando

Vel?ek, Karol

Fachgebiete

• Technische Wissenschaften Maschinenbau | Werkstoffkunde Produktionstechnik

Inhaltsverzeichnis

Influence of Cutting Parameters and Tool Geometry on Thrust Force Behavior in Drilling Ti6Al4VTool Wear and Surface Roughness Evolution in Hole Making Process of Inconel 718Comparison of Milling Strategies when Machining Freeform SurfacesSurface Roughness and Cutting Force Components Evaluation in Hard Turning by Differently Shaped Cutting ToolsResistance of Cladding Layers Made by FCAW Method to Erosive WearCladding of Wear-Resistant Layers in Metallurgy and EngineeringInfluence of Machining and Heat Treatment on Deformations of Thin-Walled BearingsThe Influence of the Filler Material on Weld Joints Made of Duplex Stainless SteelsResolving Problems of Finding Surface Boundaries during Laser MachiningEvaluation of Electrochemical Properties of Steel Sheets for Automotive ApplicationsAspects of Burnishing Rolling Process of the Surface Prepared in Different Previous TreatmentsCharacterization of Porous Coatings Obtained on Materials by Plasma Electrolytic OxidationThe Effect of Technological Conditions of Hard Turning on the Formation of White LayerSelective Laser Melting Technology and Manufacturing of Accurate Thin StructuresOn Flexural Stiffness of Polymer Sandwich WallsInfluence of Different Coupling Agent Type on Processibility and Applicability of Polymer CompositesAnalysis of Parameters with Influence on Material Shrinkage PLA and PLLAThe ?Laser Machinability? of Polymeric MaterialsThermal Degradation of the Thermoplastic Elastomers during the Injection Moulding ProcessEffect of Dielectric Barrier Discharge Plasma Surface Treatment on the Properties of Pineapple Leaf Fiber Reinforced Poly(Lactic Acid) BiocompositesDynamic-Mechanical Properties of Polymer Composites with the Short and Long Glass FibersUse of Composite Materials for FDM 3D Print TechnologyMechanical Benefits of Gas Assisted Injection Moulding Application in Design of Structural PartsOptimal Cutting Conditions for Surface Finishing of Parts Made of PhotopolymersReduction of Injection Moulded Plastic Part Warpage Using Advanced Gas Assisted Injection MouldingMetal to Composite Plastic Conversion of Mechanically Loaded Part Using Numerical CAE AnalysesThe Numerical Simulation of the Deep Drawing Process and its Verification by the Adaptation of the Laminated Tooling ConceptNumerical Analysis of Influence of Cutting Edge Radius on the Minimum Thickness of the Machined LayerNumerical Investigations of the Effect of Process Parameters on Residual Stresses, Strains and Quality of Final Product in Blanking Using SPH MethodAnalysis of Strain in Cutting Zone with FEM and Stereological Metallographic EvaluationComputer Simulation and Numerical Analysis of the Tailored Blanks DrawingStudy the Possibility of Controlling the Magnitude and Distribution of Residual Stress in the Surface Layer of the Product after the Process Double Duplex BurnishingExperimental and Numerical Investigation of the Influence of Cutting Speed and Feed Rate on Forces in Turning of SteelAnalysis of the States of Deformation and Stress in the Surface Layer of the Product after the Burnishing Cold Rolling OperationFinite Element Simulation of Physical Phenomena in Real Conditions of a Single Grain Cutting ProcessDetermining of Shear Modulus for the Samples Circular and Hollow Circular Cross-SectionModeling the Failure Tree Analysis for Safety-Critical Systems in the Production of Hazardous MaterialsApplication of 3D Printing for Specific ToolsUsing Contactless Scanning for Quality Control of Automotive PartsLaboratory Tasks and Material and Safety Aspects

Über Autor(innen)

Eds. Daynier Rolando Delgado Sobrino and Karol Velíšek