Key Engineering Materials II

Erscheinungsjahr 2012
ISBN: 978-3-03785-382-5
Verlag: Trans Tech Publications

Buch, Englisch, 1920 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 200 g

These are the proceedings of the 2nd International Conference on Key Engineering Materials (ICKEM 2012), held on 26-28th February 2012 in Singapore. The objective was to provide a forum for the discussion of new developments, recent progress and innovations in the field of key engineering materials. All aspects of design methodology were addressed and emphasis was placed on current and future challenges to research and development in both academia and industry.

Autoren/Hrsg.

Fan, Wu

Fachgebiete

• Technische Wissenschaften Maschinenbau | Werkstoffkunde Technische Mechanik | Werkstoffkunde

Inhaltsverzeichnis

Preface, Organizing Committees and Sponsors
Chapter 1: Materials Behavior
Resistive Polymer Memory Materials Containing Electron Donor and Acceptor Moieties
Numerical Study on Impact Response of Aircraft Sandwich Wing Made of Fiber-Metal Laminate Face-Sheets Subjected to Bird Strike
Light Absorption and Structural Properties of TiO2-AgCl Thin Films Doped with Cu by Sol-Gel Process
Research on the Strength Improvement of 7A04 Aluminum Alloy
Synthesis and Characterization of SnO2/N-Doped TiO2 Nanoparticles
Effects of Temperature, Strain Rate and Grain Size on Superplastic Behavior of Magnesium
Effect of Distributed Attached Mass on the Vibration of Sandwich Panel Using Higher Order ESL Theory
Effect of Curvature and Thickness of Aluminum Shells on the Energy Absorption in Low Velocity Impact
Effects of Water as Non-Solvent Additive on Performance of Polysulfone Ultrafiltration Membrane
Study on Warm and Hot Tensile Deformation Behavior and Flow Stress of AZ31B Magnesium Alloy Sheet
Reactive Blends of Poly(butylene adipate-co-terephthalate) and Thermoplastic Starch
Properties of Compatibilized SAN/NR Blends
Heating Effect on the Qualities of Cr-Zr-N Thin Films by Increasing in Zr Sputtering Current
Microscopy Observation on Nanocellulose from Kenaf Fibre
Synthesis and Properties of Sb Layered Te/Cd Stack Prepared by Elemental Stack Method
Effect of Clay on the Properties of Polyoxymethylene/Clay Nanocomposites
Investigation on the Deformation Pattern and Energy Absorption Capacity of Hot-Stamping Structures with Partial Pressing Hardening
Mechanical Properties of Montmorillonite-Filled Natural Rubbers Compatibilized by Epoxidized Natural Rubbers
Low Temperature Solvolthermally Synthesized Nitrogen-Fluorine Doped TiO2 for Methyl Orange Photodegradation
Optical Properties of NiO Thin Films: A Potential Material for Optoelectronic Devices
Physical Properties of PP/Recycled PET Blends Prepared by Pulverization Technique
Transport Properties of Chitosan/Peo Blend Based Proton Conducting Polymer Electrolyte
Martensitic Transformation and Response Characteristics in Bias-SMA Spring Actuators with Thermal Cycling
Inverse Estimation of Viscoelastic Material Properties Based on Particle Swarm Optimization and Neural Network

Ab Initio Electronic Structure Studies of CuO Multiferroics
Laboratory Study and Evaluation on a Novel Clearfrac Fluid System
Effects of End-Groups on Properties of Hyperbranched Polyether
Curing Behavior Characterization of Phenolic Resin Derived from Starch
A Study on Ployacryamide Solution Viscosity Analysis at Low Shear Conditions
Performance Study of Humidity Adsorbent Prepared from Waste Shells
Degradation of Butylparaben by Ozonation and UV/TiO2 Processes
Microstructure Evolution during Thermal Aging of Fe-Cu Alloys
Formation Mechanism of Ceria Particles by Spray Pyrolysis
The Role of Form Compositions in Energy Consumption of High-Rise Buildings (Case Study: Iran, Tehran)
Fracture Behaviour of Chemically Treated Reshira-Epoxy Composite and Optimization of Parameters for Composite Fabrication
Influence of Unground Palm Oil Fuel Ash (UPOFA) in Compressed Earth Brick (CEB) Properties
Densification Behavior of Steatite by Two Stage Sintering
Optical Behaviour of Transparent Thin Films of Sr-Doped TiO2 for Optoelectronic Devices
Evaluation of the Physiochemical Properties of Molybdenum Supported Catalysts
Polymeric Antioxidant Based on Natural Rubber Grafted with N-(4-Hydroxyphenyl)maleimide
Synthesis and Characterization of Fluorescent Acrylamide Water Soluble Macromer
Photocatalytic Degradation of Active Brilliant Red on TiO2/SiO2 Composite Catalysts
Ferromagnetism, Raman Spectra and Photoluminescence of Sn0.91Co0.05Ce0.04O2 and Sn0.91Fe0.05Ce0.04O2 Nanorods
Free Vibration Analysis of FGM Sandwich Beams Containing Edge Cracks
Analysis of Surface Rolling Process Impact on Crankshaft Fatigue Strength
Chapter 2: Casting and Solidification
Effect of the Two-Step Solution Heat Treatment on the Microstructure of Semisolid Cast 7075 Aluminum Alloy
Effects of Aggregate Gradation on Water Permeability of Concrete
Influence of Polypropylene Fiber in Strength of Foamed Concrete
Self-Compacting Concrete Prepared Using Rice Husk Ash Waste from Electric Power Plants
Research of Ecological Planning of River Landscape Used Ecological Concrete
Reduction in Defect Rate by Taguchi Method in Plastic Injection Molded Components
Challenges and the Way Forward for Building Materials Management in Building Adaptation Projects
Chapter 3: Powder Metallurgy and Ceramic Forming
Centrifugal Atomization of Zinc Metal Powder for Friction Materials Application
Compositions and Particle Sizes of (RE)Ba2Cu3O7-X Superconductor Powders Synthesized by the Solution Combustion Technique
Bulk Crystallization of Ceramic Whiskers from Borate-Based Glass
Anisotropy and Forming Characteristics of Magnesium Alloy ZE10
Investigations of Tungsten Based Intermetallic Alloys by Self Propagating High Temperature Synthesis from Metal Oxide Precursors
Effect of Al Mole Ratio on Iron Aluminide Reinforced with TiB2-Al2O3 Composite by Self-Propagating High-Temperature Synthesis
Low Temperature Synthesis of Pb(Zr0.52Ti0.48)O3 Ceramic Powders by Chelating Agent Assisted Sol-Gel Process
Effect of Grain Size on the Shape Recovery in a Melt-Spun Fe-24%Mn-4%Si-5%Cr-5%Co SMA Ribbon
Effe