Science and Materials Engineering IV

Selected, peer reviewed papers from the Fourth National Congress of Science and Materials Engineering (CNCIM 2013), February 22-28, 2013, Pachuca, México
Erscheinungsjahr 2014
ISBN: 978-3-03835-156-6
Verlag: Trans Tech Publications

Buch, Englisch, 280 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 660 g

Collection of selected, peer reviewed papers from the Fourth National Congress of Science and Materials Engineering (CNCIM 2013), February 22-28, 2013, Pachuca, México. The 49 papers are grouped as follows: Chapter 1: Synthesis, Obtaining and Materials Modification, Chapter 2: Materials Characterization, Chapter 3: Materials Applications, Chapter 4: New Materials Development and Simulation Materials

Autoren/Hrsg.

García-Serrano, Jesús

Herrera-Gonzalez, Ana María

Coreño-Alonso, Juan

Cardoso-Legorreta, Edgar

Fachgebiete

• Technische Wissenschaften Maschinenbau | Werkstoffkunde Technische Mechanik | Werkstoffkunde

Inhaltsverzeichnis

Preface, Committee, Organizers and Sponsors
Chapter 1: Synthesis, Obtaining and Materials Modification
Synthesis of New Hexakis-Heterocyclic Compounds and their Use in the Formation and Stabilization of Au and Ag Nanoparticles
Corrosion Resistance of Hot Dip Aluminized Copper Alloys
Effect of Mechanical Vibration during the Solidification Process of an Aluminium Alloy A356
Immobilization of SA-a-2,6-Gal Receptors Related to Influenza on Magnetic Nanoparticles Coated with Chitosan
Physical Properties of Thin Films of GaAs and AlxGa1-xAs Grown by Solid-Arsenic-Based MOCVD
Solid Solutions Study of BaTiO3 Doped on B Site by Electronic Compensation
Structural and Textural Study of Highly Porous Carbon Nanospheres
Study of the Effect of Synthesis Method on Obtaining Ca0.3La0.7MnO3
Synthesis and Characterization of Azobenzene-Containing Polydiacetylene Polymers
Synthesis and Characterization of CdSe Nanoparticles with Cadmium Precursor Variation in Colloidal Synthesis
Synthesis and Evaluation of Bifunctional Monomers Derived from Post-Industrial PET as Crosslinking Agents for Acrylic Monomers
Synthesis and Mechanosynthesis of N, N’-bis (thylthyenil)-2,3-butanediimine with Corrosion Inhibitor Properties
Synthesis Method for Obtaining Anode-Supported Tubular Solid Oxide Fuel Cells by Slip Casting
Synthesis, Characterization and Mesomorphic Properties of N,N'-(1,4-Phenylene(methanylylidene))bis(4-(hexyloxy)aniline)
Synthesis, Characterization and Optoelectronic Properties of Oligo(p-Phenylenvinylidenequinolines) with Different Substituents
Thermodynamic Study of Leached Metals (Cu, Zn and Ni) from Waste Printed Circuits by Electrochemical Method
Chapter 2: Materials Characterization
Analysis of Hardness, Resistivity and Corrosion of HfN Thin Films Fabricated by D.C. Sputtering
Biocompatibility Evaluation of Co-Ribbons Prepared by Melt-Spinning
Chemical Conditions for ZnS Thin Films Preparation by Chemical Bath Deposition
Corrosion Resistance on the Interlayer of AISI 316L/AISI 304 Stainless Steels Joined with an Iron Based Metallic Glass Ribbon at 1000 °C by Induction Heating
Dissolution of Iron from Oxides in a Solution of Citric Acid and Sodium Thiosulfate
Ductile Powders Mechanically Alloyed in an Effective Way
Effect of Substrate Temperature on the Properties of Hafnium Nitride Films Prepared by DC Sputtering
Electrical Characterization of Interface Defects in MOS Structures Containing Silicon Nanoclusters
Electrical Properties of Porous Carbon Powders Synthesized by Nanocasting of Aniline in Mesoporous Silica
Electrochemical Synthesis of Palladium Nanoparticles on HOPG Electrode
Influence of the Temperature on the Diffusion Coefficient Value during the Cobalt Electrodeposition on Different Substrates
Microstructural and Thermal Characterization of Copper Based Composites for Thermal Management in Electronic Packaging
Precipitation Hardening Analysis of an Al-8%Ag Alloy
Study of Cantilever Structures Based on Piezoelectric Materials for Energy Harvesting at Low Frequency of Vibration
Synthesis and Characterization of Copper(II) Complexes with Long Chain Dithiocarbamates
The Influence of Temperature and Carrier Gas Flow in the Obtainment of Carbon Nanotubes by Chemical Vapor Deposition
Thermal Behavior, Chemical, Mineralogical and Optical Characterization of Clays (Kaolin) for Industrial Use as Refractory Material
Thermodynamic Study of Iridium in HCl: The Effect of Concentration
Wear Characterization of Nodular Cast Iron Based on Clusters of Nodules
Chapter 3: Materials Applications

In Vivo Biocompatibility of Dental Scaffolds for Tissue Regeneration
Bismuth and Gold Nanoparticles Prepared by Laser Ablation in Aqueous Solutions
Developing Alternative Building Materials from Mining Waste
Elimination of Dyes Present in Textile Industry Wastewater Using Adsorbent Materials Prepared from Broccoli Stem
Photocatalytic Degradation of Malachite Green Dye and Pharmaceuticals Using Co:TiO2 Thin Films
Selective Recovery of Zn(II) and Fe(III) by Liquid - Liquid Extraction Using Cyphos IL 109 as Extractant
Strength Insertion Implant Fixed on Trabecular Bone Density Based on Insertion Torque and Pull Out
Synthesis of Silver Submicroparticles and Nanoparticles over Microfiltration Membranes Impregnated with Surfactants
Chapter 4: New Materials Development and Simulation Materials
Anisotropic Emission in Strain-Balanced Quantum Well Solar Cells
Composites Manufactured with Recycled Pet and Reinforced with Zinc Particles
Development and Characterization of Cementing Composites with Blast Furnace Slag Replacement
Effect of Nanostructures on Corona Poling Assisted Second Harmonic Generation in Hybrid Organic-Inorganic Films
Obtaining Al2O3/Ti/TiO2-Functional Graded Material through Air Oxidation of Al2O3/Ti Composite
Rutile Molecular Model and its EUC Determination by PM7