Buch, Englisch, 226 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 530 g
Buch, Englisch, 226 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 530 g
ISBN: 978-3-03835-748-3
Verlag: Trans Tech Publications
Autoren/Hrsg.
Fachgebiete
Weitere Infos & Material
Preface, Committees
Chapter 1: Analysis Properties and Production of Cements and Concretes
Influence of Fly Ash and Basalt Fibers on Strength and Chloride Penetration Resistance of Self-Consolidating Concrete
Rheological Optimization of Self Compacting Concrete with Sodium Lignosulfate Based Accelerant Using Hybrid Neural Network-Genetic Algorithm
Error Estimation of Linear Polarization Resistance Measurement Caused by IR Drop for Reinforcement Corrosion in Concrete
Belite Cement Prepared from High Carbon-Content Fly Ash
Uncertainty Analysis in Fatigue Life Prediction of Concrete Using Evidence Theory
Effect of Cement on the Engineering Properties of Pavement Materials
Relationships for Size and Dispersion of Pores with Mix Factors for Cement Sand Mortar
Chloride Ion Diffusion Model of the Concrete under Multiple Factors
Experimental Study on Hematite Concreting
Study of the Technical Capability of Sugarcane Bagasse Ash in Concrete Production
Effect of Substitution of Crushed Waste Glass as Partial Replacement for Natural Fine and Coarse Aggregate in Concrete
Structural Properties of Concrete Containing Ground Waste Clay Brick Powder as Partial Substitute for Cement
Effects of Concrete Mix Proportion on Electrical Resistivity of Concrete
Economic Exploitation of Gravel in Place of Granite in Concrete Production
Influence of Portland Cement Brands and Aggregates Sizes on the Compressive Strength of Normal Concrete
Performance Using Boiler Ash Clinkers as Replacement for Course Aggregates in Concrete
Influence of Mineral Admixtures on Fracture Energy of Refractory Cement at Elevated Temperatures
Research on Physical and Hydration Heat Characteristics of the Multi-Component Cementitious Materials
Durability of Red Mud Based Geopolymer Paste in Acid Solutions
Chapter 2: Design and Analysis Properties of Structures
Structural Behaviour of Ferrogeopolymer Slabs under Flexure
Effects of Carbon Fiber Reinforced Polymer Strips on the Flexural Strength and Deflection of Steel I-Beam
Seismic Upgrading of a Masonry Church with FRP Composites
Laboratory Tests of Reinforced Concrete Beams with the Use of Operational Modal Analysis
Influence of the Anchorage of PBO-FRCM Composites on the Effectiveness of Behaviour of Shearing Beams
The Reliability Analysis of the Initiation Time for RC Members under Chlorine Salt Ingress and Local Micro-Climate
Structural Damage Assessment of FRP Strengthened Reinforced Concrete Beams under Cyclic Loads
Producing High Strength Hollow Core Reinforced Concrete Slab with Silica Fume and Polypropylene Fibers
Chapter 3: Material Properties and Processing Technologies
Impact of Tool Pin Geometry and Optimized Process Parameters on Mechanical Properties of Friction Stir Welded AZ80A Mg Alloy
Synthesis Route of ZnO Nanostructures in Basic Solution
Effect of Hydroxyl Concentration on the Structural and Optical Properties of Zinc Oxide Nanoparticles
Antibacterial Properties of Unique Urchin-Like CuO Nanostructures by Chemical Bath Deposition
Development of Photocatalytic Self-Cleaning Cotton Fabric
Influence of Gel Aging Time on the Properties of Various Silica Aerogels Synthesized from Water Glass
Rapid Densification of Forsterite Ceramic via Microwave Sintering
Identification of Kinematic Hardening Material Parameters for Martensitic Steel Sheets
Cyclic Voltammetric Study of the Pitting Corrosion Behavior of Low-Nickel Austenitic Stainless Steels in Citric Acid
Effect of Temperature and Cooling Rate on the Microstructures of 35MnB and 25Mn Tubes during Heat Treatment
Empirical Modeling of Sound Absorption Properties of Natural Nonwoven Fabric (Antiaris toxicaria Barkcloth)
Plane Waves of Dilatation in Auxetic Bulk Solids
