Buch, Englisch, 432 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 860 g
Buch, Englisch, 432 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 860 g
ISBN: 978-3-0357-1142-4
Verlag: Trans Tech Publications
Autoren/Hrsg.
Fachgebiete
Weitere Infos & Material
Preface
Chapter 1: Properties of Structural Materials
Effect of Hydrogen Trapping and Poisons on Diffusion Behavior of Hydrogen in Low Carbon Steel
Study on Preparation and Modification of Oil-Soluble Nano-MMT
Application of 3D-DIC Method on Crack Forming Process of Concrete under Axial Compression
Effect of Current Density on the Microstructure and Corrosion Properties of MAO Coatings on Aluminum Alloy Shock Absorber
Study on Microstructure and Properties of Nanocomposite Coating Prepared on the Surface of Exhaust Pipe for Ship
Study on the Residual Stresses Distribution in Thick Pre-Stretched Aluminum Plate
Experimental Study on Surface Element Composition and Hydrophobic Properties of DLC Coating
The Influences of Surface Roughness on the Water Contact Angle for Coated Substrate with F-DLC
The Influence of Surface Welding Using EDTCrMnSi Special Wire on the Wear Resistance of 16Mn Steel
Research on Friction Property of Pin on Disc and Analysis of Wear Mechanism Based on MMW-1A Friction and Wear Testing Machine
Chapter 2: Technologies of Materials Machining in Mechanical Engineering
Experimental Research on Electroforming Nano-ZrO2 Reinforced Cu-Matrix Composite Aided by Pulse Power
Effect of Abrasive Particle Size on Lapping of Sapphire Wafer by Fixed Abrasive Pad
The Thermal Stress Simulation of the Part Caused by Layer Thickness and Deposition Velocity in FDM Process
Research on Electronic Discharge Grinding of Polycrystalline Diamond Based on Response Surface Method
Fabrication and EDM Corrosion Resistance of Copper Electroforming Layer on Tube Electrode for Aero-Engine Blade Cooling Hole in EDM Process
The Investigation of the Effect Caused by Deposition Velocity on Bonding Degree within the Structure of FDM
Quantitative Study on Abrasive Belt Wear Based on Geometric Parameters
Influence of Nano Al2O3 Particles on Morphology and Microstructure of Cu-Al2O3 Composite Coating by Jet Electrodeposition
Research on Milling Deformation in Ultrasonic Vibration Assisted End Milling of Titanium Alloy Thin-Walled Parts
Finite Element Analysis on Single Abrasive Grinding Ti6Al4V Alloy
Nanosecond Laser Direct-Part Marking of Data Matrix Symbols on Titanium Alloy Substrates
The Roll-Forming Process Analysis of the Situation and Development Trend
Effect of Ultrasonic Vibration Assisted Grinding Process on Surface Topography and Properties of C/SiC Composite
Research on the Quality of Laser Marked Data Matrix Symbols
Optimization and Affections of Cathode Feed Angle on Machining Accuracy Error Distribution of Aero-Engine Blade in Electrochemical Machining
Study on Honing Mechanism of Gear Surface Using an Internal Honing Wheel Based on Single-Particle Abrasive
Study on Two-Step Aging Technology of 6082 Aluminum Bumper
Research on Milling Force in Ultrasonic Assisted End Milling of Titanium Alloy Thin-Walled Parts
Cutting Performance of Reaming Alloy Gray Cast Iron HT250 Using Carbide, Cermet and CBN Reamers
Simulation Analysis of RuT450 Drilling Force Based on LS-DYNA Gun Drilling
The Effect of Cutting Force Vibration on Machining Quality for Reaming ZL102 Alloy with PCD Step Reamer
Chapter 3: Process Modeling and Optimization of Technological Parameters and Tool in Materials Machining
Feed Optimization of Cycloidal Bevel Gear Format Cutting Based on Equal Cutting Area
Study on Simulation of Stamping Forming and Die Surface Optimization of Aluminum Alloy Plate
Melt Mold Casting Process Optimization of Train Coupler Based on ProCAST
Research on the Effect of Cutter Position Points Distribution Optimization on Surface Milling Accuracy
Parametric Programming of Multi-Type Holes Using the Improved Genetic Algorithm
The Cutting Parameter Optimization in Helical Milling of Ti Alloys with Small Diameter Tools and the Study of their Cutting Performance
Study on Parameter Optimization and Tool Wear of Milling Compacted Graphite Iron RuT450 Cylinder Block
Research on Metamorphic Vibration Casting Process Based on EDEM-FLUENT Coupling
Study on High-Frequency Fatigue Properties of PVD AlTiN Coating of Cutting Tool
Analysis of Computational Model of Seamless Steel Pipe Rolling Contact Force
Grinding Process of Ball End Milling Cutter Flank
Dynamic Response Analysis of Tandem Rolling Mill in Rolling Process
Instantaneous Uncut Chip Thickness Model in End Milling Based on an Improved Method
Research on GC Cup Truing Technology of Super-Hard Grinding Wheel
