Buch, Englisch, 314 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 670 g
Buch, Englisch, 314 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 670 g
ISBN: 978-3-0357-1605-4
Verlag: Trans Tech Publications
Autoren/Hrsg.
Fachgebiete
Weitere Infos & Material
Preface
Chapter 1: Nanomaterials and Nanostructures
Vapor-Phase Axial Deposition Synthesis of SiO2 and SiO2-TiO2 Sponge-Shaped Nanostructures
Structural Investigations on Hydrothermally Grown ZnO Nanostructures
Effect of Processing Parameters on the Diameter and Morphology of Electrospun Iron-Modified Montmorillonite (Fe-MMT)/Polycaprolactone Nanofibers
Anodization of Highly Ordered Titania Nanotube Prepared with Organic Electrolyte
Study on Mechanical Properties of Multilayer Graphene/Epoxy Nanocomposites
Chapter 2: Polymers and Composites
Effects of Micro-Eggshells Filler on Tracking and Erosion Resistance of Silicone Rubber Composites
Study of Machining Parameter Optimization in Drilling of Magnesium Based Hybrid Composites Reinforced with SiC/CNT
An Internal Damage Real-Time Monitoring System Using CFRP-OFBG Plates
Effect of Surface Treatment on Interface Strength of CFRP/Metal Hybrid Composites
Assessment of Silicone Rubber Properties Using Dynamic Modelling Simulation
Chapter 3: Steel, Alloys, Machining Technologies
Thermomagnetic Analysis of the Crystallization in Soft Magnetic Nanocrystalline Alloys
Semi-Solid Forging of Mg Alloy AZX1311 and Mechanical Properties
Grain Characteristics of 1235 Aluminum Alloy during Rolling
Macrosegregation Characteristics of Ferrite and Austenite Stabilizer Elements in Large Size High Strength Steel Ingot
Corrosion Behavior and Mechanical Properties of New Developed Oxide Precipitation Hardened Steels
Effect of Space Holder Size on the Porous High Purity Aluminum Property
Machining Parameters Mapping’s of Inconel 718 and Aluminum Alloy 1100 in Micro-Milling Process
Preliminary Design of Two Dimensional Vibration Assisted Machining System for Multi-Axis Micro-Milling Application
Mechanical Characterization of Aluminium Alloy 6061 Powder Deposit Made by Friction Stir Based Additive Manufacturing
Investigation on Friction Coefficient Considering Al-Si Coating Layer Fracture of Boron Sheets in Hot and Cold Deep Drawing
Machined Surface Roughness Geometry Model Development on Ultrasonic Vibration Assisted Micromilling with End Mill
Internal Friction Study of the Bake-Hardening Properties on Low Carbon Steel Influenced by the Degree of Pre-Deformation
The Effects of Cutting Parameters to the Surface Roughness in High Speed Cutting of Micro-Milling Titanium Alloy Ti-6Al-4V
Burring Process and Fracture Criterion of Large Diameter Steel Pipe
Burr Formation in Casting Using Vertical-Type High-Speed Twin-Roll Caster
Casting of Thin Bare Wire Using Wheel Caster Equipped with Rotating Side-Dam Plates
Wear and Adhesion Properties of High-Pressure Torsion Processed Carbon Steel
Experimental Investigation on the Failure Mechanism of Grooved Steel Plate Impacted by Projectile with Different Nose Shapes
Chapter 4: Materials for Biomedical Application
Formation of TiO2 Thin Film on Antibacterial Metal Injection Molding Stainless Steel Orthodontic Bracket 17-4 PH Using Physical Vapor Deposition Method
Alkali-Heat Treatment of Ti-6Al-4V to Hydroxyapatite Coating Using Electrophoretic Method
The Mechanical Properties of Sisal/PMMA and Sisal/Carbon/PMMA Biomedical Composites
Fish Scale Collagen Functionalized Thermo-Responsive Nanofibres
Chapter 5: Building Materials and Engineering
The Measurement of Shrinkage: Influence of Specimen Size
Effect of Partial Oxidation Rubber on Hydrophilicity of Cement Composites
Effect of CO2 Curing on the Strength of High Strength Pervious Concrete
Study on Fatigue Life of Cement Stabilized Macadam Base during Crack Expanding Phase Based on Accelerated Loading Test
Wind Speed Effect on the Time Available for Compaction of Warm Mix Asphalt (WMA)
Analysis of Lateral Torsional Buckling Strength of Single Symmetric I Beam
Structure Monitoring and Long-Term Behavior Prediction of Wall-Piloti Structure
Application of Bacteria as Self-Healing Agent for the Concrete and Microscopic Analysis of the Microbial Calcium Precipitation Process
Pilot Study of Mechanical Waves Passing through Fine-Grained Cement Composite during the Early Hydration Process
Chapter 6: Materials and Technologies in Biomass Processing and Chemical Engineering
The Functionalization of Activated Carbon by Oxidation
The Formation of Local Catalyst from Zeolite, Characterization and Performance in the Reaction
Impact of Pulsed Electric Field on Glycerin Sedimentation from Biodiesel Production Process
Upgrading Bagasse Quality by Torrefaction for a Biomass Power Plant
Identification of Cacao Peels Potential as a Basic of Electrodes Environmental Friendly Supercapacitors
Weighted Spacer Design for Elevated Temperature Conditions to Mitigate Barite Settling by Identifying Suitable Viscosifier
Correlation between Void Fraction and Two-Phase Flow Pattern Air-Water with Low Viscosity in Mini Channel with Slope 30 Degrees
