Iqbal / Hasanuddin / Akhyar | Advanced Technologies in Material Processing | Buch | 978-3-0357-1655-9 | sack.de

Buch, Englisch, 142 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 380 g

Iqbal / Hasanuddin / Akhyar

Advanced Technologies in Material Processing


Erscheinungsjahr 2020
ISBN: 978-3-0357-1655-9
Verlag: Trans Tech Publications

Buch, Englisch, 142 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 380 g

ISBN: 978-3-0357-1655-9
Verlag: Trans Tech Publications


This volume contains papers presented at the International Conference on Experimental and Computational Mechanic in Engineering (ICECME, Indonesia, 18-9 September 2019) in conjunction with 9th AIC 2019 International Conference which reflect the last research results and engineering decisions in the area of materials science and technologies of materials processing.
Iqbal / Hasanuddin / Akhyar Advanced Technologies in Material Processing jetzt bestellen!

Weitere Infos & Material


Preface
Role of Size of Rubber Particles on Failure Mode and Impact Resistance Characteristics of PC/ABS Blends and their ABS Constituents with a Higher Rubber Content
Properties of High Strength Concrete with Calcined Diatomaceous Earth as Cement Replacement under Compression
Investigation of Meniscus Effect on Microbond Test of Typha Fiber/Epoxy Matrix
Study on Fracture Failures of the Super Heater Water Pipe Boiler
Thermal Spray Application on the Dissimilar Metals Weld between Aluminum and Steel
Fatigue Life Assessments of the SAE 5160 Carbon Steel Subjected to Uphill and Downhill Roads Strains
Fatigue Life Assessments of the AISI 1513 Carbon Steel Subjected to Road Surface Strains
Fatigue Life Assessments of the AISI 1513 Carbon Steel of a Vehicle Lower Arm Subjected to Clockwise and Counter-Clockwise Road Strains
Flexural and Splitting Tensile Strength of High Strength Concrete with Diatomite Micro Particles as Mineral Additive
Influence of Forestry and Agriculture By-Products as Filler Materials on Thermal Conductivity of Fiberboard Panels Applied for Heat-Conditioned Building Partition Wall
The Effect of Rotation Speed and Dwell Time on the Zn Distribution of the Dissimilar Metals Friction Stir Spot Welded between Aluminum Alloy and Galvanized Steel
The Effect of Process Route on the Mechanical Properties and Microstructure Aluminum Al-Si-Cu-Mg-Mn Alloys
Effect of Machining Parameters on Hole Accuracy and Burr Formation in Micro-Drilling of Brass
Optimization of Machining Process Parameters Using Moora Method
Numerical Simulation of the Effect of Shoulder Rotation on the Tensile Strength of FSW Dissimilar Joints of Aluminum Alloy
Effect of Different Gating Systems and Sand Mold Binder on the Cast-Quality of Bicycle Frame Produced through Sand Casting Method
The Investigation of Hole Delamination in Drilling Kevlar Composite Panel Using HSS Drill Tool
The Preparation and Characterization of Fe-ZnO Nanoparticles Immobilized onto Fiberglass Cloth
The Effect of Spindle Speed and Feed Rate on Hole Diameter of High-Speed Micro-Drilling for Micro-Screen Manufacture


Ihre Fragen, Wünsche oder Anmerkungen
Vorname*
Nachname*
Ihre E-Mail-Adresse*
Kundennr.
Ihre Nachricht*
Lediglich mit * gekennzeichnete Felder sind Pflichtfelder.
Wenn Sie die im Kontaktformular eingegebenen Daten durch Klick auf den nachfolgenden Button übersenden, erklären Sie sich damit einverstanden, dass wir Ihr Angaben für die Beantwortung Ihrer Anfrage verwenden. Selbstverständlich werden Ihre Daten vertraulich behandelt und nicht an Dritte weitergegeben. Sie können der Verwendung Ihrer Daten jederzeit widersprechen. Das Datenhandling bei Sack Fachmedien erklären wir Ihnen in unserer Datenschutzerklärung.