Manufacturing Science and Engineering I

Erscheinungsjahr 2010
ISBN: 978-3-908454-99-1
Verlag: Trans Tech Publications

Sonstiges, Englisch, 4720 Seiten, Format (B × H): 125 mm x 142 mm, Gewicht: 200 g

This book brings together the latest advances in, and applications of, manufacturing science and engineering. It comprises 976 papers, selected from among 3062 papers which were submitted by universities and industrial laboratories all over the world. All of chosen papers were subjected to strict peer-review.

Autoren/Hrsg.

Jiang, Zheng Yi

Zhang, Chun Liang

Fachgebiete

• Technische Wissenschaften Maschinenbau | Werkstoffkunde Technische Mechanik | Werkstoffkunde

Inhaltsverzeichnis

Blade Diamond Disk for Conditioning CMP Polishing PadThree-Point Bending Test Behaviour of a QFN Semiconductor PackageStructural and Optical Properties of Dy Doped ZnO Film Grown by RF Magnetic SputterThe Progress of Fixed Abrasive Wire Saws in the Last DecadePhotocatalytic Analysis and Characterization of Zn2SnO4 Nanoparticles Synthesized via Hydrothermal Method with Na2CO3 Mineralizer An Optimization of Two-Steps Curing Profile to Eliminate Voids Formation in Underfill Epoxy for Hi-CTE Flip Chip PackagingThe Crystal Structural Properties of Sputtered ZnO Films Containing Internal StressThe Comparison Research of Two Working Electrodes in Electrochemical Reduction of Silicon TetrachlorideEffect of Ca Content on Mechanical Properties of 4N Gold Wire for Quad Flat Nolead (QFN) Stacked Die PackageCharacterization of 0.5 ?m BiCMOS Gate Oxide Using Time Dependent Dielectric Breakdown Test Dynamic Analysis of Optical Brittle Crystal Slicing by Using WiresawOn the Warpage in the Lower Case of Lead-Acid BatteriesEffect of Forming Parameters on the Mechanical Properties of Thixomolding AZ91D Magnesium AlloyAnalysis on Transmission Characteristics of New Axis-Fixed Cycloid GearResearch on the Key Technologies for New Large Dual-Platen High-Precision Clamping SystemAnalysis of Tension and Deformation Curvature in Strip Tension LevellingThe Modulus Mensuration of Yada Model and the Microstructure Simulation of Casting AZ31 Magnesium AlloyStrip Shape Analysis of Asymmetrical Cold Rolling of Thin StripExperimental Research on Coaxial Extrusion of GF/Pb Complex WireNumerical Simulation of Push-Bending Process of Aluminum Section ProfileThe Effect of Entrance Temperature on Texture and Microstructure Development in Cold Mill Rolled 85/15 a-Brass Numerical Simulation and Process Test for Cold Extrusion of Wheel Hub Bearing Rings Effect of Bonding Pressure on Transient Liquid Phase Bonding Joint Microstructure and Properties of T91/12Cr2MoWVTiBFinite Element Simulation of Backward Ball Spinning of Thin-Walled Tube with Longitudinal Inner RibsOn Spontaneous Austenite Recrystallization of Low Pressure Rotor Steel 26Cr2Ni4MoVResearch on Intelligent Deep Drawing Technology of Sheet MetalNew Methodologies for the Determination of Precise Forming Limit Curve in Single Point Incremental Forming ProcessA New Springback Compensation Method for Sheet Metal Bending Based on Curvature Correction Thermo-Mechanical Numerical Simulation on P91 Closed Upsetting ProcessInfluence of Hot Working Conditions on Mechanical Properties and Microstructures at Weld Zone of the Ti3Al /TC4 Dual AlloyStudy on Work Hardening Performance of Pure Shearing Fine-Blanking with Negative Clearance for ASTM-Gr.D and ASTM-1022 SteelStudy on the Impact of Fine-Blanking with Negative Clearance on the Materials Microstructure and HardnessInfluence of Isothermal Forging Temperature on Microstructure and Tensile Properties of Ti-5.8Al-4.0Sn-4.0Zr-0.7Nb-0.4Si-1.5Ta Near-a Titanium AlloyNumerical Simulation on the Effect of Process Parameters for Incremental Sheet FormingDetermination of Winding Tension in Manufacturing Strip Wound DieStudy on Deformation Mechanism of Tube HydropiercingAn Investigation of Fineblanked Surface of Cold-Rolled 45 SteelSimulation and Analysis on Microstructure Evolution of Large Generator Retaining Ring during Multi-Fire Forging Preparation and Characterization of Well-Dispersed Nd1.6Eu0.4Zr2O7 Solid Solution and its Fluorescent BehaviorUltra-Fine Grained Fe-32%Ni Alloy Processed by Multi-Axial ForgingComparative Study of the Process Fracture between Fine-Blanking with Negative Clearance and Conventional BlankingThe Influence of Integrated Strength on Bulging Cracking of Tailor Welded Blanks Advanced High Strength Steel Sheet Forming and Springback SimulationImproving Plastic Thermoform Quality with Uniform Heating TechnologyNumerical Investigation of Viscoelastic Flow and Swell Behaviors of Polymer Melts in the Hollow Profile Extrusion ProcessThe Design Method of Punches and Dies for Progressive Die of Motor Core Based on Association Design TechnologySolution of Singularity Points in Strip Rolling by Rigid Plasticity Finite Element MethodEffect of Ultrasonic Wave on Melt Foaming Process of Aluminum FoamStudy on the Differential Thickness Ratio Effect on Formability of TWB Based on Numeric Simulation Research on Stamping of Aluminum Alloy Hemispherical Components Based on Numerical Simulation and Experiments Extrusion Modeling of Solid Plug Flow of Co-Rotating Twin Screw Pulping Extruder Optimum Design on Trapezoidal Thread Parameters of Co-Rotating Twin Screw ExtruderResearch on Stamping Spring-Back Prediction for Car Body Panel Based on BP Neural Network Investigation on Thermomechanical Treatment of PM FGH4096 SuperalloyInvestigation on the Formability of Tailor-Welded BlanksSpringback Prediction of Axial Symmetry Sheet Part DrawingResearch of Geometric Parameters Related to TRB Uniaxial TensionDevelopment of CAD System and Forming CAE of Porthole Extrusion Moulds for Hollow Aluminum ProfileStudy on the Dynamic Behaviors of X70 Pipeline Steel by Numerical SimulationNumerical Analysis on Hot Stamping of B Pillar Reinforcement of Automobiles Fatigue Life Prediction of Isothermal Forging Dies Based on Average Strain MethodHot Deformation Behavior and Hot Processing Map of P92 SteelLimit Pressure of Rupture Discs Found on Tensile Instability ConditionThe Effect of Isothermal Forging Parameters on the Microstructure and Properties of Ti-5Al-5Mo-5V-1Cr-1Fe Titanium AlloyInvestigation of the Relationships between Billet Reheating and Semi-Solid Die-CastingThe Forming Scheme of a Silencer Cover in Progressive DieNumerical Analysis and Optimization of Stamping Technology for Electrical Motor?s Cover Plastic Deformation Characteristics Analysis in Rotary-Draw Bending Process of Thin-Walled Rectangular TubeMicrostructure and Mechanical Properties of Heavy Gauge Plate by Vacuum Cladding RollingManufacture of a Seal Flange with E-Cross-SectionTemperature Effects of ECAP and Annealing after ECAP on Microstructure of TA15 Alloy Study on Bending and Upsetting Forging 305 Marine Crankshaft Improvement of Hole Flanging Product Forming Process Using Finite Element SimulationAn Analytical Solution to Metal Plane Problem in Terms of Orthotropic Anisotropy and Strain HardeningNumerical Simulation and Experimental Study on the Weld-Line Movement of Tailor-Welded Blank Spinnability of Semi-Continuous Casting 7A09 Aluminum AlloyElectromagnetic Field Simulation and Experiment of Electromagnetic Forming of Magnesium Alloy Tube Key Technology and Development on Side Pattern CAD/CAM on Mould for Auto LampHot Deformation and Processing Maps of a High Strength Alloy SteelEffect of Process Parameters on Microstructures of 30Mn20Al3 SteelExperimental Study on Csf/AZ91D Composite Using Extrusion Following Vacuum Infiltration MethodSynthesis of Intermetallic Ni3Al Alloy: Properties and High Temperature Oxidation BehaviourKey Technologies in the Design of a Vacuum Die Casting Mould for Aluminum Alloy JointsFinite Volume Simulation and Multi Parameters Optimization on Extrusion of Complex Aluminum ProfileFVM Simulation of Large Deformational Aluminum Extrusion Process and Die Bearing OptimizationNumerical Simulation and Evaluation of Local Thickness Increment in Ironing by Finite Element MethodA New Manufacturing Method for a Screw-Threaded Fuel Filler PipeExperimental Study on the Deformation of Oxide Scale and Friction during Hot Rolling of Stainless Steel 304LMechanical Properties and Microstructures of Ferritic-Rolled High-Strength Interstitial-Free (IF) Steel SheetsEstablishment and Application of Forming Limit Diagram of Multi-Gauge Laser Tailor-Welded BlanksEffect of La and La+Sr on Structure and Properties of ZL101AEffects of Shot-Peening on Cr-Rare Earth-Boronizing at Low Temperature for Medium Carbon SteelBifurcation and Chaos of a 4-Side Simply Supported Rectangular Thin Electro-Magneto-Elastic Plate in Many FieldsInvestigation on Low Cycle Fatigue Life of SC Notched SpecimensEffect of Reactive-Al2O3 Addition on the Pore Size Distribution and Thermal Conductivity of Carbon Blocks for Blast FurnaceThe Research on Process of Deep Cryogenic Treatment for W4Mo3Cr4VSi HSS DrillEffects of Nb Doping on Dielectric and Ferroelectric Properties of Bi4Ti3-xNbxO12+x/2 CeramicsStatistical Analysis of the Effect of Na2CO3 as Additive on the Reduction of Vanadic-Titanomagnetite-Coal Mixed PelletsStudy on Crack Retardation with the Consideration of Crack Surface Roughness by FEMEffects of Mg-Doping on Structure and Electric Properties of MgxZn1-xO:Al CeramicsFrequency Equations of Magneto-Thermoviscoelastic Surface WaveProbabilistic Crack Propagation Behavior of Railway B Grade SteelMicrostructure and Mechanical Properties of Cast Ti25Nb3Mo3Zr2Sn AlloyCreep Behavior of an AZ91 Magnesium Alloy Reinforced with Aluminum Silicate Short FibersThe Effect of Precipitates on Anisotropy of Al-Li Alloys 2090 and 2090+CeThe Characteristics of the Magnetic Memory Signals under Different States for Q235 Defect SamplesDielectric Tunable Properties of Ba0.6Sr0.4TiO3 Thin Films with and without LSCO Buffer LayerActivated Carbon Fiber for Super-Capacitor ElectrodeAnalysis of Fracture Failure of Diaphragm of Non-Contact Electronic HornSurface Hardness Changes after Strengthening under Low-Amplitude LoadsCompressive Response of UHMWPE/Vinyl Ester 3D Orthogonal Woven Composites at High Strain RatesEffect of Silica Sol on the Properties of Unfired Mullite RollersThe Study on Oxidation Resistance Properties of Ductile Cast Irons for Exhaust Manifold at High TemperaturesA Plastic Zone Equation Based on Mean Yield CriterionStudies on Corrosion Behavior of Q235 Steel by Iron Bacteria in Sedimentary Water from Storage TankMutual Interaction of Two Rail Surface Cracks under Thermo-Mechanical Contact LoadingEffect of Metal Powder on Blast Power of the Low Collateral Damage AmmunitionInfluence of Perlite Admixture on Pore Structure of Cement PasteResearch on the Mechanism of Aging of Dual Phase Steel Produced by Continuous AnnealingStrain-Induced Precipitation in Nb-Bearing Low Carbon Multi-Microalloyed SteelInfluence of Plastic Deformation Degree on Microstructure and Mechanical Properties of the Magnesium Alloy ZK60 after T5 Treatment Simulation and Analysis during Conveyor Stop Process Based on AMESim A Study on the Characteristic of the Ultra-Thin Copper Bonding WireEffect of Rare Earth Y Addition on the Properties and Precipitation Morphology of Aged Cu-Cr-Ti Lead Frame AlloyStudy on Al-Doped ZnO Films Prepared by Magnetron Sputtering with Rapid Thermal Annealing ProcessA Study on Crack Propagation in Bi-MaterialsInvestigation on Correlation between the Modified Criterion and the Glass-Forming Ability for Metallic GlassesInfluence of Surface Friction Mismatch on Front End Bending during Plate RollingEffect of Thinckness on Residual Stress Fields of Cold Expansion HoleTribological Behavior of Irritation Cross-Linked UHMWPE under Dry SlidingEffect of Severe Plastic Deformation Technique on the Dissolution of ?? Phase in Al-Cu Binary Alloy Abnormal Changes of the Rheological Property of Sn Melt Induced by TemperatureStudy on the Relationship between the Thermoelectric Potential and the Wear of YW1 Cemented Carbide InsertsThe Elastic-Viscoplastic Field Near Mode II Dynamic Propagating Crack-Tip of Interface in Double Dissimilar MaterialsStudy on Time-Correlated Leakage Predication Model of Nonmetallic GasketsA Novel Poly(Ferrocenyl-Schiff Base) and its Charge Transfer Complex with IodineA Numerical Method for Predicting the Young?s Modulus of CeramicStudy on Amorphous Formation Ability of Al-Fe Alloy Liquids in Hot Dip AluminizingNon-Conventional Approach for Deacidification of Fumed SilicaInvestigation of Nonequilibrium Dynamics of Nickel Film Excitated by Femtosecond LaserMicrostructural Evolutions and its Influence on Properties of Super-Duplex Stainless SteelA Three-Phase Constitutive Model for TiNiNb Shape Memory AlloysEffect of Specimen Dimensions in Dynamic Torsion TestingExperimental Comparison of Fatigue Characterizations between TRIP and DP SteelsEffects of Thermal Exposure on the Mechanical Properties and Microstructure Stability of an Al-Cu-Mg-Ag Alloy The Correlation between the Liquid Structure and the Viscosity of Sn-Cu Lead-Free SoldersAn Experimental Investigation on Static and Dynamic Fracture Properties of MgAlA Comparison of Macroscopic Fracture Surface and Crack Growth Rate of Ti-6Al-4V Study on Strain Solitary Waves in the Nonlinear Elastic Circular RodThe Stereoscopic Morphology of Martensite in Ferrous AlloysFatigue Crack Growth Behavior in Fusion Zone of 16MnR Steel WeldmentThe Study of the Relationships between Material Properties and Welding Residual StressesResearch on Initial Discontinuity State of an Advanced Aluminum Alloy Rolling Alclad SheetMaterial Constitutive Model in Machining 7050-T7451 by Orthogonal Machining ExperimentsEffect of Electrical Current on Wear Rate of Nano-Al2O3p/Cu CompositeDynamic Properties of Asphalt Binders Containing Fiber ModifiersDesign and Characterization of Ultrahigh Strength Dual-Phase Steel with Low Ratio of Yield Strength/Ultimate Tensile StrengthMicrostructural and Mechanical Aspects of High Nitrogen Steels at Cryogenic TemperatureThe Calculation of Kinetic Parameters in Manganese NitridingThe Skin Effect in a High Pressure Die Cast Mg-9%Al AlloyPreparation and Characterization of Ba0.6Sr0.4TiO3 Ceramics Doped with Al3+, Ga3+, and In3+Effect of Heat Treatment Process on Microstructure and Mechanical Properties of SWRS82B Wire RodResearch on Evaluation of Corrosion Grade Based on Image Processing Technique3-D Finite Element Analysis of Bonded Joints under Impact LoadingThe Effect of Fillet Geometry on Stress in Weld-Bonded JointsResearch on Heat Treatment Influence Factors on High-Pressure Cylinder Steel 30CrMo-MResistivity-Temperature Feature of Ga36.5Sb63.5 MeltEffects of Secondary Dendrite Arm Spacing on Microporosity of A357 AlloyAn Investigation on the Hydrogen Content in Al-12Si Alloy MeltThe Oil Lubricated Sliding Wear Behavior of In Situ TiB2 Partical-Reinforced Al-10Sn Matrix CompositesEffect of Lubricant on Surface Rolling Contact Fatigue CracksThermal Aging Embrittlement Evaluation of Nuclear Primary Pipe Steel by Ductile to Brittle Transition TestEffects of Al and Zn on the Microstructure and Mechanical Properties of Magnesium AlloysStudy on Hot Plasticity and Microstructure of Mn18Cr18 High Nitrogen Austenitic Stainless SteelA Double-Parameter K~J Fracture Criterion for Epoxy Asphalt ConcreteTest Methods for Mechanical Properties of Structural AdhesivesEffect of Welding Method on Weld Defects of ADB610 SteelExperiment and FEM study on Uniaxial Tensile of SiCp/AlStudy on Static Deformation Characteristics of Mental Rubber MaterialEffects of Coating on Interfacial Fatigue of Fiber-Reinforced CompositesCharacterization of Tensile Damage for 3D-C/SiC Composites by Acoustic EmissionTempering Resistance of a New Type of Tool Steels Used in Magnesium Die Casting MachineInfluence of HLB Parameters of Surfactants on Properties of Magneto-Rheological FluidExperimental and Numerical Evaluation of the Vibration Fatigue of Small Bore Pipe in PWROn Three-Dimensional Fatigue Crack Propagation under Constant Amplitude LoadingStrain-Based Fatigue Test and Reliability Research of 42CrMo Alloy SteelWear Behavior of Cr2O3/Cu Composite under Electrical SlidingA New Electromechanical Coupling Model for Piezoelectric ActuatorStress Relaxation Analysis of Polyurethane Foam Preloaded StructuresYield and Rheological Behaviors of Magnetorheological FluidsEffect of Rare Earth Oxide on Sintering and Crystallization of Fused Quartz Ceramic MaterialsCharacterization of Hyperelastic Dielectric Elastomer Based on Biaxial Tensile BenchEffect of Compressive Deformation on Degenerate Pearlite Transformation in a Fe-C-Mo AlloyStudy on Doping and Microwave Permittivity of SiC PowdersThe Hereditary Feature for Preferred Orientation in Ferritic Stainless SteelSustainable Manufacturing Technology and Properties of Steel Slag ConcreteAn Efficient Sampling Method for the Actual Reliability of Engineering Calculation and DesignThe Analysis of the Distribution of the Failure Statistical Data Hydrogen-Adjacent PipelinesPenetration of Cone-Nose Projectile to the Laminated Composite Aluminum Alloy Foam TargetThe Thermal Characteristics of Invar 36 Alloy during Plane GrindingCreep Continuum Damage Analysis for a Pressurized Thick Wall Circumferentially Welded CrMoV Steel Pipe at 640?CMoving Crack in an Infinite Plate of Orthotropic Anisotropy FGMs under Anti-Plane ShearEffects of Die Temperature of SSS Die Casting on the Microstructure and Mechanical Properties of ADC12 Aluminum AlloyStrain Amplitude Dependence of Damping Capacity in High Damping Mg-Based Alloys Continuously Extending to Microplastic StrainMechanical Properties of Ti-Doped DLC Multilayer by Pulse Cathodic Arc Deposition Application and Research on the Cold-Drawing Steel Wire Annealing Process under the Pulse CurrentEffect of Recessing in Bondline on Stress in Co-Axial Lap JointStress Distribution in a Piezoelectric Material with an Elliptical Hole Subjected to Remote Uniform Shear Mechanical and Electric LoadsMorphology-Controlled Syntheses, Growth Mechanisms, and Optical Properties of ZnO Nanocombs/Nanotetrapods Investigation on Fatigue Limit Based on the Series Complicated Notches for Structural SteelMicrostructure Formation at Low Velocity during Directional Solidification of Pb-Bi Peritectic AlloysThe Effect of Al-5Ti-1B and Combination Electromagnetic Field on Grain Evolution of Die Casting Commercial AluminumA New Compound Phosphate Heat-Cured Foundry BinderManufacture of the Wear Corrosion Resistance High-Cr Cast Iron ImpellerFormation of Non-Dendritic Microstructure of Semi-Solid Magnesium Alloy by Introducing Gas BubblesHomogenization Behaviors of Low Frequency Electromagnetic Casting and Direct Chill Casting 7050 Aluminum AlloyDescription of Recalescence in Bulk Undercooled AlloysStudy on Size and Microstructure of Complex Cavity Aluminum Alloy Castings Formed by Pre-Burying Copper Pipe CoreA Compound Process Preparing Semi-Solid A356 Alloy SlurryStructural Transformation in Electric Pulse Modified Liquid AluminumEffects of Low Frequency Electromagnetic Field on Hot Tear during Hot-Top Casting ProcessEffect of Withdrawal Rate on the Microstructures of a Single Crystal Ni-Base SuperalloyMicrostructure Evolution of Heavy Section Ductile IronInfluence of Sulfur on the Microstructure and Properties of High Nickel Austenite Grey Iron Study on Surface Reaction Layer of Titanium Cast with Al2O3-Based Investment MaterialsEffects of Magnetic Field on the As-Cast Structures of Dual-Ingot Low Frequency Electromagnetic Semi-Continuous CastingReclamation of Green Sand Containing Hot-Box Resin Sand and its ApplicationEffect of SDAS on Homogenization of Al-Si-Mg Casting AlloysAn Investigation on the Impurities of Aluminum Alloy in Melt FurnaceAn Investigation on the Overheating of A357 Aluminum AlloyCasting of Aluminum Alloy Clad Strip Using a Vertical Type Tandem Twin Roll CasterRoll Casting of Al-25mass%SiNumerical Simulation and Application of Electromagnetic Stirring in AnsteelMechanical Properties of Heat Treated 30CrMo Steel Produced by Compact Strip ProductionHeterogeneous Nucleation for AZ91 with In Situ Synthesis Al4C3Secondary Phases Present in Spray Formed Al-10.5Zn-2.0Mg-1.5Cu Alloy Effect of Aluminum Content on Mechanical Properties of Cast Magnesium Alloy Sheets Fabricated by Twin-Roll Casting Damping Characteristics of Biomedical Porous NiTi Shape Memory AlloyPreparation of Superfine Low-Melting-Point Metal Particles by Phase Inversion Method Preparation and Characterization of Ce-Doped Ba0.2Sr0.8TiO3 Ferroelectric CeramicsTribological Behavior of Ti(C, N)-Based and Functionally Gradient Ti(C, N)-Based Cermets The Exploration on Synthesis of Calcium Aluminate and Fe-Si Alloys Using Red Mud and Aluminum DrossEqual Channel Angular Pressing and Torsion of Pure Al Powder in TubesAn Experimental Study of Metal Co-Injection Molding with Sequential InjectionCreep Damage Analysis of Powder Metallurgy Material with InclusionPreparation and Mechanical Properties of Al2O3/TiCN Sandwich Nanocomposite Ceramic Tool Materials Carbon Foams with High Compressive Strength Derived from Mixtures of Mesophase Pitch and Si Particles Study on Friction Properties of Cu-Based Friction Materials with Ni Coated Nano-SiO2 Particles Synthesis of a-Al2O3 Platelets in Molten Salt for High Performance Ceramics Synthesis of High Nitrogen Stainless Steel Powders by High Energy Ball Milling and their SPS Compaction System Design for High Energy Rate Electromagnetic Powder Compaction DevicesAn Experimental Study of Fine Powder Comminution in a Dual Cone Impact Mill Research of Constitutive Relation of Metal Powder in High Velocity CompactionResearch on Manufacturing Technology and Heat Transfer Characteristics of Sintered Porous Surface TubesThermoelectric Properties of Iron Disilicide Prepared by Field-Activated Synthesis Process Process Investigation for Purifying Hydrated Silica from Fly Ash by Acid and Alkali Combination MethodThe Micro-Torsion Mechanism of Polarization Axis during Fabrication of Polarization Maintaining Fiber DevicesPost-CMP Cleaning of Atom-Scale Planarization Surface of Computer Hard Disk SubstratePrediction of Surface Roughness Profiles for Milling Process with Fractal Parameters Based on LS-SVMAnalysis of the Stress Invariants Criterions for I-II Mixed Mode Crack Initiation AnglesStructural, Optical and Electronic Properties of Cu-Doped ZnO Films Synthesized by RF Magnetron SputteringStudy on the Mechanism of the Cobalt Leaching of Cemented Carbide in Triethanolamine SolutionEffect of Non-Steady State Loading on Rolling-Sliding Contact StressEffects of Lanthanum on Fe-25Cr Alloys under Cyclic OxidationResearch on Damping and Vibration Characteristic of the Large and Precision NC Rotary TableStress Field of Semi-Infinite Interface Crack Tip of Double Dissimilar Orthotropic Composite MaterialsDebonding Analysis along a Softening FRP-Concrete Interface between Two Adjacent Cracks in Plated BeamsCorrosion Resistance of Ni-Y2O3 Composite Coating Prepared by Electrodeposition under Ultrasonic ConditionThe Simple Model of the Oil Film Thickness between Piston Ring and CylinderInfluence of N2 Proportion on Mechanical Properties of SiCN Thin Films Prepared by DIBSDResearch of Contact Pressure of an Elastoplastic Rough Body in Contact with a Smooth Rigid PlaneA Study on Diffusion in Hot-Dip AluminizingExperimental Study on Surface Roughness and Residual Stress by End Milling 69111-Stainless SteelSubstrate Roughness Effects on Chromium Oxide Coating Adhesion and Wear ResistanceA Three-dimensional Finite Element Method for Surface EffectsCharacteristics of Fretting Wear in a Press-Fitted Shaft Subjected to Bending LoadWavelets-Based Feature Extraction for Texture ClassificationExperimental Study on Fracture Behavior of UHTCC Overlay/Concrete Interfaces under Mixed-Mode Loading Preparation of Iron-Oxide Coated Porous Ceramics Filter and Adsorption and Degradation on Methylene BluePreparation and Characterization of Electroless Co-Ni Coated ZrO2 Powder for Microwave AbsorbingThe High Temperature Property of Ni/WC Infiltrated Composite Layer on Cast Iron Substrate The Microstructure of Polyaniline Coatings Electropolymerized on Pb Substrate in Aniline+Oxalic Acid ElectrolyteResearch on the Effects of Atomization on Different Liquid Dielectrics in a High Voltage Electrostatic Field Study on Vehicle Wheel Automatic Recognition Based on the Manufacturing Research of Characteristics of Ni-W-P Nanocomposites Containing CeO2 and SiO2 Particles The Microstructure and Properties of Coating from Mo2FeB2 Cermet on Surface of H13 Steel by Reactive Flame SprayingNovel Method for Improving Surface Performance of Rolling Bearing Raceway Gradient Characteristic of Functionally Graded Cemented CarbideEffects of Voltage on the Characteristics and Corrosion Resistance of Microarc Oxidation Coatings on Ti6Al4V AlloyStudy on the Preparation and Alleviating Fretting Wear Property of Ni-Tl-B Coatings on Steel Effect of WC Grain Size on the Abrasive Wear Resistance of HVOF Spraying WC-Co CoatingsCopper Multilayer Coating Prepared by Ultrasonic-ElectrodepositionNanostructured Surface Layers In Low Carbon Steel and Pure Titanium Induced By High-Speed Rotating Wire-Wheel DeformationTribological Behavior of Molybdenum Alloying Layer on H13 Steel by Electrospark Deposition Technique Synthesis and Characterization of Nickel-Iron-Silicon Nitride Nanocomposite Wear Behavior Of Chromizing-Titanizing CoatingSherardizing and Characteristic of Zinc Protective Coating on High-Strength Steel Bridge Cable Wires Enhancing Steam Oxidation Resistance of Ferritic Steels through Formation of Nickel Aluminide Diffusion Coatings at Low TemperaturesMicrostructure and Wear Resistance of TiC+Cr7C3 Reinforced Ceramal Composite Coating Produced by PTA Weld-Surfacing ProcessRemanufacturing of High Temperature Ball Valve by Surface Engineering TechnologyOxygen Evolution Kinetic Parameters of Electrodeposited Composite Inert ElectrodesPulse Electrodepositon of Ni-W-P-CeO2-SiO2 Composite CoatingsFabrication of Bionic Silicon Surfaces with Lotus Effect and their Micro Tribological Performance Effect of Diffusion Treatment on High-Temperature Oxidation Resistance of Multi-Arc Ion Plating Al Films on TiAl AlloyTemperature Field Simulation for Aluminum Alloy Surface Modification by Scanning Electron BeamSynthesis and Characterization of NiCoFeCrAl3 High Entropy Alloy Coating by Laser Cladding Optical and Mechanical Properties of Silver Film on Glass SubstrateControl-Steps and Influence Factors of SiO2 Electrodeposition Process with Zn CoatingsAmorphization of Fe-Ni Based Alloys by Laser Cladding and RemeltingThe Optical Properties of Sputtered ZnO FilmsInfluence of Laser Surface Texturing Distribution Patterns on the Hydrodynamic LubricationFinite Element Analysis of the Temperature Field and Strain Field of Coating Rod in Friction Surfacing A Statistical Model for the Joint Distribution of Droplet Size and Charge Density in an Electrostatic SprayCu-Ni-Ti Composite Diffusion Coating of the Al2O3 Ceramic Surface and its Joining MechanismPreparation and Properties of the Ni3P-TiO2 Coating on Carbon SteelInfluence of Rare Earth on the Properties of H13 Steel by the QPQ Salt-Bath TreatmentAnti-Wear Property of Self-Repairing Mineral Particles as Grease Lubricant Additives on the Metal Friction PairsFabrication of n-SiO2 Reinforced Al2O3 Composite Coatings on 7A52 Aluminium Alloy by Micro-Arc OxidationBrush Plated Multilayered Cu/Ni Coating from a Single Electrolyte and its Fretting Wear Behaviors Influence of Ultrasonic Peening on Wear Resistance of U70 RailsSurface Hardening of Spot-Welding Copper Alloy Electrode for Zinc Coated SteelStructure and Oxidation Behavior of Gradient Zr/ZrN/Zr Diffusion Barrier on the Ni-Based Superalloy by Arc Ion Plating The Process of Electroless Plating Ni on the Surface of Carbon FibersMicrostructure and Corrosion Resistance of Free-Sprayed Ni60 Coating Prepared by High Frequency Induction HeatingAdaptability Study of an Ideal Linear Elastic Constitutive Model for a Plasma Sprayed Ceramic Thermal Barrier Coating The Influence of Laser Hardening on the Microstructure and Wear Resistance of Disk OpenerInvestigation of Nano Composite Coating on Aluminum Alloys Treated by Plasma Transferred ArcHigh Temperature Wear Behaviors of Electro-Brush Plating Ni-P CoatingsMicrostructure and Wear Properties of Laser Clad TiN/Co-Based Composite CoatingEffect of Rare Earth Addition in Plasma Nitriding on Microstructure of Chromium Electro-PlatingMicrostructure and Reciprocating Sliding Tribological Performance of Micro-Arc Oxidation Coating Prepared on Al-Si AlloyErosion Wear Behavior of Coatings with Growth Defects Produced by Ion Beam Enhanced Pulsed Filtered Vacuum Arc DepositionRotational Fretting Wear of Ion Nitrided Medium Carbon SteelMicrostructure Characteristic of Laser Cladding Ceramic Layer on High Cr Cast Steel SurfaceOxidation Study of APS Thermal Barrier Coatings in Elevated TemperaturesGrowth Behaviour of ZnO on Si (100) and Platinum Coated Glass Substrate from Aqueous SolutionInfluences of Different Calcinations Ambience on Phase Composition and Morphologies of Ceramic Coatings on Ti Alloy by Micro-Arc OxidationEffect of Sulfurizing Temperature on Formation of Coatings Produced by Nitriding-Sulfurizing Composite Treatment for Ti-6Al-4V AlloyResearch on In-Flight Property of Particles in Plasma Spray Forming Numerical Modeling of the Fracture Process of a Three-Unit All-Ceramic Fixed Partial Denture Synthesis of TiO2/Polymer Composite Microspheres Using Functional Porous Polymer Particle as Substrate Vibration Suppression of Flexible Beams Using MR ElastomersStudy on Activated Carbon /Polyaniline Electrode Materials for Supercapacitorsts Synthesis of (TiC)pNi/TiAl/Ti Graded Material via Field-Activated and Pressure-Assisted Combustion Process Characteristics and Elastic Modulus Evaluation of Pd-Nafion Ionic Polymer-Metal CompositesReasearch on Heat-Shocking Resistance of SiC(w)/ZrO2-MoSi2 Ceramic CompositesPreparation and Damping Capacities of the NiTiSMA/FC CompositesEffects of Technological Parameters on Microstructures of Semi-Solid Magnesium Matrix CompositesThe Preparation and Photocatalytic Activity of SWNTs Doped ZnO/TiO2 Compound FilmsTensile and Bending Strengths of TR-30s Carbon Fiber Three Dimensional Braided Composites at Different TemperatureThe Study of Mechanical Properties of Structural Lightweight ConcreteReaction Mechanism of an Al-TiO2 SystemMicrostructure Evolution and Mechanical Behavior of CNTs/ AZ31 Magnesium Alloy Composites Processed by Equal Channel Angular PressingHigh Strain Rate Superplastic Deformation Behavior of TiNP/2014Al Composite Effects of Al Content on Phase Composition of Zr-Al-O-N CompositesPreliminary Study on VGCF Reinforced Cement CompositesExperimental Investigation on Drop in Tensile Performance Index of Carbon Fiber Composite in Use Effects of Nano-Al2O3 Additions on Microstructures and Properties of WC-8Co Hard Metals Preparation of NiTi/NiTiNb Laminated Alloys by Vacuum Brazing Tic Particle Reinforced Iron Based Composite Coating by Submerged-Arc Welding Added Alloy PowderParametric Modeling Method for Composite Microstructure Virtual TestingManufacture and Tribological Properties of C/C-SiC Brake Composites Fabricated by Warm Compacted In Situ ReactionInfluence of Nanosilica/Polyurethane Composite Coating on IR Effectiveness and Visible Light Transmission Properties of Polyethylene Design, Production and Mechanical Property of White Engineered Cementitious CompositesPreparation of TiO2-g-Polystyrene Nanosphere and its Application in Toughening PS Matrix Friction and Wear Behaviors of Si3N4 Sliding against M50 Bearing Steel in Vacuum Effects of Surface Modification of SiC Nanoparticles and Preparation Process on Microstructures of SiCp/A6061 Alloy Matrix CompositesTransverse Elastic Deformation Behavior of Aligned Fiber Bundles under Bulk Compressive Pressure and Longitudinal StressSynthesis and Mechanical Property Evaluation of Ti-TiAl Metal-Intermetallic Microlaminate Composite Interfacial Treatment of Multi-Layer Woven Silk Reinforced Epoxy CompositesFracture Characteristics for Crack Tip near the Interface between Steel and Concrete in Composite Structures Energy-Based Debonding Model for Steel-Concrete Composite Structures Study on Figuration Techniques of Grades Extrusion for Making Metal Rubber Material Analysis of Mesoscopic Interfacial Mechanics of RC Beams Strengthened with FRP Comparative Research on the Effects of the Self-Healing Microcapsules on the Modal Properties of Composite Brake Study on TiCp/Al Master Alloy in Magnesium Matrix CompositesCopper-Based Electronic Materials Prepared by SPS and their PropertiesResearch on Methods for Elastic Stiffness of Multi-Ribbed Slab StructureExperimental Research on Low-Velocity Impact Properties of 3D Braided CompositesA Finite Element Model to Simulate the Cutting of Carbon Fiber Reinforced Composite MaterialsSynthesis and Catalytic Activity of Composite Materials TiO2/Ti-Al-MCM-41 by Chemical Vapor Deposition (CVD)Study on Reaction Synthesis Mechanism of TiC-Al2O3 Particle Co-Reinforced Aluminum Based CompositesEffect of Hollow Structure on the Electromagnetic Interfering (EMI) Shielding of Aluminum-Cenospheres Composites The Numerical Simulation of Co-Curing Process for AGS PlateThe Characteristics of Multilayer Thin Films Deposited with Metal Thin Films (Ag, Al, Cu)Glass Fiber Permeability Using the VARTM ProcessMicroscopic Analysis of Flow and Prediction of Effective Permeability for Dual-Scale Porous Fiber Fabrics The Higher Order Asymptotic Fields for a Anti-Plane Crack in a Linear Functionally Gradient Material Mechanical Evaluation of the Production of Bamboo Charcoal/ Stainless Steel Complex Yarns and Knitted FabricsAnalyses on the Manufacture and Physical Properties of Electromagnetic Shielding/ Far Infrared Ray NonwovenMechanical Analyses of Repeatedly Processed Polypropylene/Carbon Fiber Composite PlatesManufacturing Technique and Physical Property of Metal Wires/ PP Nonwoven Selvedges Complex Ply Yarns and Knitted FabricsManufacturing Process of Sound Absorption Composite PlanksThe Study on the Surface Morphology of Al/SnO2-Sb2O3 or SnO2-Sb2O3-MnO2/PbO2 Electrode MaterialResearch on the Surface Change of the Large Optic Plane Wafer In the Fast Polishing Process Effects of Tool Geometry and Workpiece Hardness on Surface Roughness in Finish Hard Turning of AISI 440C Transient Dynamic Analysis of the Matching of Lengthened Shrink-Fit Holder and Cutter in High-Speed Milling Cutting Mechanism of Multi-Tooth Tool for Manufacturing Metal FibersPerformance Evaluation of Minimum Quantity Cooling Lubrication Using CBN Grinding WheelAnalytical Modeling of Workpiece Surface Temperature Rise in Machining Theoretical Analysis and Experimental Investigation into Hydrodynamic Pressure and Coolant Lift Force in Flood Delivery GrindingResearch on Surface Machining System for Light Metal Thin-Walled Parts Based on Spherical CoordinateResearch on Wear Mechanisms while Turning Titanium Alloy TC4Study on the Stability of High-Speed Milling of Thin-Walled WorkpieceEnhancing Machined Parts Surface Quality by Using a Composite Material for Tool Body in Turning Experimental Investigations of Tool Wear Mechanisms in Machining 1Cr18Ni9Ti Stainless SteelExperimental Study of Improved Tool in High Manganese Steel DrillingDetermination of the Anti-Chatter Weak Component on a Machine ToolThe Friction Coefficient and Self-Organization Feature on Rake Face when Turning Hardened Steel with Coating ToolsStudy on Causes of Material Plastic Side Flow in Precision Hard Cutting ProcessAn Experimental Investigation of Cooling-Air Grinding PerformanceDesign and Motion Simulation of Floating Die Polishing Device Microscopic Examination of Primary Shear Zone in High Speed Machining of Hardened High Strength SteelCrater Wear Modeling in Conventional Speed MachiningVibration Analysis Based on AR Trispectrum in Milling ProcessStudy of Grinding Method of Twist DrillsThe Influence of Spray Characteristics on Surface Roughness in Minimum Quantity Lubrication TurningA Study on Cutting Force in Micro End Milling with Ultrasonic VibrationAcoustic Emission and Vibration Analysis of Process of Hard Dry MillingFailure Mechanisms of Carbide Tool in High Speed Milling of Inconel 718Experimental Study on Relation between Tool Wear and Grinding Force for Shaping Diamond ToolExperimental Study on Milling Force of High-Temperature Alloy GH536Finite Element Simulation of Ultrasonic Vibration Orthogonal Cutting of Ti6Al4V Friction Torque of Rotating Hydraulic Cylinder with Deep Circular Groove Oil Film Face SealResearch on Precision Grinding System and Key Technology Based on PMAC-PCResearch on Chatter Suppression in Machining Thin-Walled Components Based on Rigidity OptimizationA Bioreactor for a Pulsatile Circulatory Culture SystemStudy on Metals Behavior Subjected to Cyclic Loading Based on Bauschinger Effect of Reversible Fine Machining SequenceAnalysis of Cutting Forces in Precision Turning Based on Oblique Cutting ModelA Technical Study of Hole Drilling in Ceramics/FRP Laminate Composite Components Design of an Ultrasonic Vibration Deep-Hole Honing DeviceExperiment and Theory of Cutting Forces for Cemented Carbides Based Self-Lubricated Tool Embedded with Solid LubricantsStudy on the Cutting Mechanism of Remanufacture Deposited Materials in the Impactive ConditionResearch on Tool-Chip Friction during Ti6Al4V Milling Process with Different Cooling/Lubrication MethodsRole of Chip Serration Frequency in Chatter Formation during End Milling Operation of Stainless Steel Prediction of Flank Milling Forces in Ruled Surface Impeller Machining Nonequivalent Milling of Roller Gear Cams Based on Approximation Method of Offset Surface Study on Precision Grinding of Involute Cams on a Double-Disc DeviceTrajectory Interpolation in CNC Grinding of Indexable InsertsA Soft CNCS on Windows-XPFour-High Mill with Statically Determinate Characteristics of Micro Displacement of the ComponentsCFD Research on Aerostatic Bearing with Tangential Supply HolesResearch on Plastic Rolling Forming Process of Plate-Fin by Numerical Simulations and ExperimentsSSA Based Decomposition of Tool Position Trajectory for Diamond Turning of Freeform Optical SurfacesAssessment of Machining Characteristics of Austempered Ductile Iron Influence of Radial Depth of Grinding and Finishing Process on Surface Residual Stresses in Grinding AF1410 Ultrahigh Strength SteelResearch on Surface Roughness Prediction Model for High-Speed Milling Inclined Plane of Hardened SteelCutting Forces and Tool Wear Patterns in Five-Axis Milling Fe-Based Super Alloy with Bull-Nose End Mill Research on Design and Application of Control System in Machine Tool ModificationTool Wear Investigation on Dry Electrostatic Cooling in Turning Titanium Alloy Ti6Al4VEffect of Burnishing Process on Surface Characteristics of Particulate Reinforced Iron-Base CompositesExperimental Research on Turning Vibration Deduction with Intelligent Material Based on LabVIEW Machinability Prediction of Workpiece Material with a Diagraph MethodThermal and Shear Characteristics Study of Various Mechanical Polishing MaterialsEffect of Tool Inclination Angle on Surface Quality in 5-Axis Ball-End Milling Non-Special Dressing Electrode Experimental Study on ELID GrindingThe Grinding Head Design in Non-Circular Gear Grinding Teeth Based on the Planar Regions Interference Inspection An Investigation on the Heat Partitioning in Grind-HardeningThe Control Algorithm of Ultrasonic-Magnetorheological Combined Finishing for Rotary Symmetrical Aspheric SurfaceVacuum Dehumidifying Dryer for PET ChipsFailure Mechanism of Twist Drill in Vibration Drilling of DuraluminEffects of Grinding Wheel Vibration on Surface Quality of Axisymmetric Aspheric LensStudy on the Modeling Method for Finite Element Analysis of Chip Formation ProcessStudy on Helical Drill Point Grinding with a Biglide Parallel GrinderA Mathematical Model of EEBP for HSM Surface Quality PredictionResearch on Safety Decline of High Speed Milling CutterCMP Behavior of a-Alumina-g-Polyvinylpyrrolidone Composite Abrasive on Hard Disk SubstratePreparation of Maghemite-Silica Nanocomposites Using Sol-Gel TechniqueBiomolecule-Assisted Synthesis of Ribbon-Like Sb2S3 NanostructureLow Temperature Synthesis of TiO2 Nanorods with Tunable Aspect Ratios from Ti and NH4Cl PowdersPreparation of Novel Silica Nanoparticle/Polystyrene Composite Microspheres in a Pickering EmulsionStrain Gradient Plasticity Theory Based on Dislocation - Controlling Mechanism for Nanocrystalline MaterialsThe Improvement of Generalized Particle Method for Nano-Materials Molecular Dynamics SimulationRefinement of Microstructure in Steels through Thermomechanical Processing Equivalent Continuum Models for the Simulation of Mechanical Properties of Carbon Nanotube by Global-Local Homogenization MethodPreparation of Manganese Zinc Ferrite Nanoparticles by Polymer Matrix Templated SynthesisPreparation of Y2Ti2O7 Nanocrystal by Sol-Gel Method and its CharacterizationSelf-Assembly of Cuprous Oxide Micro/Nanostructures by Photo-Reduction MethodA Dimensional Analysis Model for Geometric Size Effects of Single CrystalsFabrication of Gold Cap-Shaped Nano-Particle Films and Sensing Device for Bioanalytical ApplicationDevelopment of Ultra-Precision Grinding Process for Aspheric Surface Based on Feed Rate Controlling and Error Compensation MethodsEffect of ZnO Nanoparticles on the UV Light Fastness and Climate Resistance of PVC Film Structure and Magnetic Properties of Carbon Encapsulated Co Nanoparticles Prepared by the Pyrolysis of Mixture of Sucrose and Cobalt NitrateFe-Based Micro- and Nanocomposite Coatings Produced by Amorphous Alloy Crystallization Based on Electrospark DepositionPreparation and Photoelectric Performance of Eu3+-Doped Porous TiO2 Thin Film ElectrodeA Hybrid Pso and Shuffled Complex Evolution Algorithm for Order Assignment Problem in Holonic Manufacturing System Effect of Combined Shot Peening Process for Surface Nanocrystallization Method on Fatigue Strength of TC4Experiment on Nano-Sized Activated Carbon/Zn-MnO2 Electrode MaterialThe Effect of Precipitates on the Bio-Corrosion Property of As-Cast Mg-Zn-Y AlloysStudy on Biomedical Resources of Benzene/Alcohol Extractives of Eucalyptus Leaves by GC/MSEffect of Solution Treatments on the Microstructures and Mechanical Properties of Mg-2Zn-0.8Mn-0.5Ca AlloyResidual Stresses in Fabrication of Core-Veneered Ceramic ProsthesesFabrication of PLLA Scaffolds by Low-Temperature Deposition from a Ternary Polymer-Solvent SystemEvaluation of Electrospun Poly (Vinyl Alcohol) (PVA)/Gelatin Nanofiber Membrane and BiocompatibilityEvaluation of the Surface of PLA/?-TCP Powder Complex BraidDissolution Resistance of Bovine Teeth-Derived HydroxyapatiteSintering and Mechanical Property of Tuna Bone-Derived HydroxyapatitePreparation of CaCO3-Containing Geopolymers for Green ConcreteEfficient Machining of Artificial Hip Joint ComponentsEffect of Water Glass on Compressive Strength of Aluminosilicate-Based GeopolymerEffect of LPG Injection Methods on Engine PerformanceHigh Intensity Glassed-Block Was Prepared by Fluid CinderSimulating Production Lines of Recycling WEEE Products in eM-PlantWaste Beverage Containers Automatic Green Recycling Technique Based on the Optical Image InspectionThe Theoretical Analysis and Experimental Study on Heat-Transfer in Cryogenic Pneumatic Mist Jet CoolingExperimental and Theoretic Research on Solar Power Membrane DistillationA New Type of Cooling-Air Generator for Cooling-Air GrindingProcess Parameters Optimization for Green Manufacturing of Laser Cladding Based on Artificial Neural NetworkAn Automatic Shake Mechanism for the Biomass Pyrolysis Feeding The Adaptive Blade Design and Evaluation of Wind Turbine A Wireless Solution of Distributed Monitoring and Control System in Optical Aspheric GrindingStudy on the Performance and Biodegradability of Three Kinds of Biodegradable Dishware Exploration and Application of Process Approximation Method on Cleaner Process EvaluationA Method of Multi-Environmental Spatial Scales Division in LCA Based on Chinese Region-SpecificExperimental Study on Heat Transfer Characteristics of Apparatus for Recovering the Waste Heat of Blast Furnace Slag Feasibility Study for the System of Coal Gasification by Molten Blast Furnace Slag Fluid Clamping Devices Based on Area Effect Stroke Amplifier Driven by Shape Memory Alloys Wires Study on MQL in Point Grinding Process for Green ManufacturingVibration Characteristics of Ni Thin Film Diaphragm by Acoustic WaveStudy on Tool Wear of Cutting Ti-6Al-4V with Water Steam as Coolant and Lubricant in Green MachiningModification of Pellet Materials by Low Temperature PlasmaH-Infinity Robust Control Methodology of Multi-Variable NCSsEvaluating Process Design through Quality Function Deployment for Environment Adaptive Fuzzy Control of Cutting Temperature Based on Cutting Fluid in High-Speed MachiningNovel Non-equidistant Optimum GM(1,1) Model with Modified nth Component be Taken as Initial Value and its Application to Metal Cutting Study on an Inventory Decision Model in an Assembly System Design and Study of Multi-Function Asphalt Mixture Shear ApparatusSimilarity-Based Integrated Scheduling of Machining Processes in the NC Resource GridVelocity Control Method for Continuous Short Line Segment High-Speed Machining Based on Transition of Parametric SplineResearch of Sequencing Working Steps Method for Box PartDynamic Reentrant Scheduling Simulation for Assembly and Test Production Line in Semiconductor IndustryThe Conjugation of the Hardened and Grinded Worm GearAn Effective Immune Based Approach for the No-Wait Flow Shop Scheduling Problems with Multiple Machines A Production Scheduling Method for Bell-Type Batch Annealing ShopFiltered Beam Search Based Flexible Job Shop Scheduling Problem with Transportation TimeA Symbolic OBDD-Based Algorithm for Assembly Sequence PlanningAn Improved Genetic Algorithm for Multi-Objective Flexible Job-Shop Scheduling Problem Optimization of Printed Circuit Board Assignment and Component Allocation in Assembly LineStudy on the Scheduling Problem of Powder Painting Production - A Case StudyAn Optimization Approach for Semiconductor Wafer Fabrication Scheduling ProblemModeling and Simulation of Re-Entrant Semiconductor Wafer Fabrication Lines with PM Using GSPN Improved Adaptive Genetic Algorithms for Job Shop Scheduling ProblemsA New NURBS Tool Path Generation Algorithm for Precise Sculptured Surface Machining Research on Dynamic Reconfigurable Manufacturing Process Framework Based on MDAApplication of Grey Correlation Analysis on Tool SelectionDesign and Analysis of Big-Character PrinterNeural Network Based Computer-Aided Process Design System for Wire Bonding Quality ImprovementAnalysis and Stress Optimization Design of an S-Shaped Micro Spring Design and its Experiments of Micro Electrochemical Machining SystemResearch for Combustor Based on Micro-Thermoelectric Generator Device Study on Micro-Displacement Stage Driven by Piezoelectric ActuatorApplication of Ultrasonic Vibration Shoe Centerless Grinding Technique to Micro-Scale Parts FabricationUltra Precision Surface Grinding for Large Scale Non-Axisymmetric Aspheric Lens Experimental Study on Viscous Dissipaition of Polymer Melt in Micro-Channels Study on the Manufacturing Method of the Biomimetic Drag Reducing Morphology Replication Mold Laminated Photoresist Sacrificial Layer Process for 3-D Movable Suspension Microstructures in LIGA-Based Surface MicromachiningNumerical Simulation and Experimental Investigation of Tool Edge Radius Effect on Micro-Cutter Wear in Micro-End-Milling Process Experimental Study on the Cutting Performance of Ultra-Precision Micro Milling MachineNumerical Simulation and Optimization on Casting Technique of HT200 FlywheelExperimental Research on the Vibration Characteristics of Flexural Vibration Disk Production Logistics Simulation System for a Rail-Beam Plant Based on Component Technology Numerical Simulation and Experiment of Aluminum Sheet Metal Springback in New Quenching StateThe Research of Structural Optimization on Diesel Engine Injection NozzleDie-Pressing Parameters Optimization Based on FEA Dynamic Simulation of Position Servo System of Pneumatic Manipulator Based on AMESim and SimulinkFinite Element Simulation of Temperature Field in Fused Deposition Modeling The Study on Suppression of Dimples in Digital Multi-Point Stretching Process Flexible Multibody Simulation Approach in the Analysis of Friction WinderPrediction and Analysis of Forged Workpiece?s Precision in Hydraulic Press Based on BP Neural Network and Genetic AlgorithmAnalysis of Assembling and Working Stress of Compound Rings High-Pressure Vessel of 5GPaVirtual Machining on Helical Bevel Gear with New Type Heavy Duty Helical Bevel Gear Milling Machine ToolEffects of Opening Hole Geometric Parameters on Hole-Edge Stress Field of Plates According to a Complex Variable Function ModelSimulation and Optimization on the Injection Molding for Auto-BumperSimulation Study on Magnetic Field Characteristics of High Magnetic Field Intensity Permanent Magnet Magnetic FilterThe Application of MR Fluid Damper to the Vibrating Screen as the Enhance of Screening EfficiencyNonlinear Dynamic Behaviors and Bifurcation of Symmetrical Rotor System Supported by Self-Acting Gas Jounal BearingsMolecular Dynamic Simulation on Mechanism of Ultrasonic Wire Bonding in Electronic PackageHigher Order Harmonic Wave and its Effect on Thermosonic Bond SystemCSP-Driven Schedule Optimization in NC Equipments Grid Considering Complex Correlated Process FlowsThe Fatigue Life Prediction of Pistons Based on the Cumulate DamageInfluence of Preparing of Specimen on Internal Stress Measurement of Aluminum Alloy Thick PlateAn Adaptive Local Meshfree Updated Lagrangian Approach for Large Deformation Analysis of Metal FormingHydroforming Simulation and Experiment on Al 5083 T-ShapesResearch on the Fault Diagnosis of Trenchless Drilling Pneumatic Impact Device Based on Grey Relational TheoryStudy on On-Machine Measurement of Rotating Tools Based on Image Processing The Series-Parallel Robot Coordinates Polishing System Based on the Multi-AgentThe Studies on Influence of Assembling Technologic Parameters on Dynamic Characteristic of Sleeve StructureThe Drum Height Detection Model of the Shearer Cutting Memory Program ControlCollection Mode Optimization of Casting Dust Based on TRIZ Analytical Model of Thermal Stress for Encapsulation and Service Process of Solar Cell ModuleImpact Studies on the Setting Styles of Stiffened Board to the Ultimate Strength of Tubular K-JointsCollaborative Manufacturing Resources Configuration Based on Summary Process Routes Study on Indexable Inserts for Gear GasherDynamic Decoupling Control of Electro-Spindle Supported by AC Hybrid Magnetic Bearings Based on Neural Network Inverse MethodStrength Analysis of Coiled Tubing in the InjectorMathematical Model for Closed-Form Solution of Parameters of Cylinder Exhaust Port in Variable-Stroke EngineA Wavelet-Based Finite Element Method for Modal Analysis of BeamsDigital Manufacturing System of Aircraft Wing Integral PanelNumerical Simulations of the Fluid Flow and Heat Transfer during a Solidification Phase Change of a Polymer in a DieCause Analysis of Longitudinal Cracks in Closure Segment of an Extra-Large BridgeA Simplified Method Study of Aluminium Alloy Fatigue Crack Tip Parameters Computed by Elastic-Plastic Finite Element ModelThe Manufacturing Resource Modeling of Multistage Manufacturing System Based on the Capacity Manufacturing UnitThe Experiment Research of Continual Extension of Surface CrackEffects of the Gear Tooth Modification on the Nonlinear Dynamics of Gear Transmission SystemDesign and Manufacture of a New Large-Scale Three-Dimensional Geomechanics Model Test SystemThe Numerical Simulation of Air Bulge Forming of Profiled CanTwo Dimensional Vibration-Assisted Micro-Milling: Kinematics Simulation, Chip Thickness Computation and AnalysisMATLAB-Based Kinematic Analysis on Mechanisms of Multifunctional WheelchairHydraulic Performance Research of a Fixed Fire Water MonitorEffect of External Magnetic Field on the Flow and Heat Transfer in DC Arc Plasma TorchDesign and Jet Characteristics Study of a Liqumatic Fire Water Monitor with Self-Swinging DeviceFlex Gradient Optimization on Stiffened Steel Plate of Profiled Plate Rubber Support 3D Loading Path-Generating Method for FEM Simulation of Incremental Sheet Metal Forming ProcessThe Study on Vibration of Marine Riser under Deep WaterVibration Isolation Study on Coupled Vibration of Load Floor Caused by Iron Ore Pelletizing Machine on itConstraint Reaction Forces and Lagrange Multipliers in Multi-Body SystemsSimulation of Failure in the Refractory Lining of Coke Dry QuenchingModeling Method of Crawler Crane Based on Open Source Engines A FEM Formulation for Flexible Multi-Body System Dynamic Analysis Motion Planning of Tomato Harvesting Manipulators with 7 DOFResearch & Realization on Neural Network for Forecast of AM Automatic Logistics Information-SystemSimulation Based Model Experimentation with Minimum Solving StrategyStudy on Cost Minimization of Auto Engine Product Warranty Chain Pressure Pulsation Analysis of Aircraft Hydraulic Power Pipelines SystemThe Research on Milling Temperature and Heat Deformation of Tool in Virtual Numerical Control SimulationStudy on the Formulas of the Dog-Bone Shape of Edger Rolling in Hot Strip Mill Sticking Analysis of the Bistable Inductive Micro-SwitchMulti-Scale Numerical Simulation of H62 Brass for Hot-Extrusion Process The Function Simulation of TBM Based on Virtual RealityFinite Element Analysis of Pressure Coiled Forming Process to Taper Weld Pipe Effect of Process Routing on Machining Deformation for Multi-Frame Double Sided Monolithic Components Determination of Expanding Pressure of Hydraulically Expanded Tube-to-Tubesheet JointThree-Phase Power Factor Correction Converter Based on One-Cycle Control in Aircraft Electric Power SystemA Novel Multiple RBF-NN Model for Rolling Force Prediction Based on Anti-Aliasing Wavelet AnalysisThe Stiffness Analysis and Modeling Simulation of Ball Screw Feed System Analysis of the Performance for a Group-Annulus Type Oil-Fired Boiler Effect of Diesel Nozzle Geometry on Internal Cavitating FlowA Novel Boundary Extraction Algorithm on Triangular Meshes of STL ModelInfluence Factors on Finishing Temperature of Plate RollingAutomatic Solder Joint Defect Classification using the Log-Gabor Filter Numerical Analysis of Grinding Fluid Field in GrindingStudy on Prediction of Machining Distortion for Titanium Alloy Aircraft Monolithic Component by FEMStrip Profile Control in Asymmetrical Rolling by FEM Modeling Formation Mechanism and Simulation of Oxide Film in Electrodeless ELID GrindingA Framework of Cooperative Design for Aspheric Glass-Lens MoldPrediction and Prevention of Overburning Structure during Hot Processing of Chromium Forged SteelAnalytic Modeling of Rolling Force during the Hot Rod Rolling of Multiple Alloying SteelsSimulation of Thermal Deformation for Spindle of Machine ToolCrawler Cranes Modeling Method Based on OGRENumerical Simulation of Double Rollers Clamping Spinning Process for FlangingNonlinear Numerical Optimization Design Applied to Wall-Thickness of Welding T Shaped Connecting HDPE TubeOn the Control System for Blank-Holder Force in Deep Drawing Based on Self-Tuning Fuzzy-PID ControllerA Parallel Numerical Study of Transient Heat Transfer and Fluid Flow of Weld Pool during Laser Keyhole WeldingTemperature and Stress Analysis in Micro-Cutting of Ti-6Al-4V and Al7050-T6A Finite Element Analysis for the Characteristics of Cutting Parameters in 3D Oblique Milling ProcessSimulation and Experimental Investigation for the End Milling Process of 7075-T7451 Aluminum AlloyResearch on Machining Simulation System for Optical Free-Form SurfacesThe Algorithm of Acoustic Location for Boiler Tube LeakageSimulation of Compressive Strength of SiC FoamSimulation of Aluminium Foam Compressive PropertiesMoment Stability of Stochastic Regenerative Cutting ProcessSimulation of Microstructure Evolution for Two-Phase Ceramic Tool Materials at Different Duration TimeAn Integration-Based Stochastic Finite Element MethodOptimization of Surface Roughness Based on Multi-Linear Regression Model and Genetic AlgorithmA New Ultraprecision Machining Method with Softness Abrasive Flow Based on Discrete Phase ModelResearch on Precision Forming Technology of Car Steering KnuckleFinite Element Analysis on the Roll Milling Process of Twisted Oblate TubeMechanical Analysis on the Inner Surface Crack of Modified 9Cr-1Mo Seamless Steel Tubes Rolled by Mandrel MillFinite Element Simulation of the Effects of Mould Angle on the Equal Channel Angular Pressing for Al-Zn-Mg-Cu AlloySimulation of Void Defect Evolvement during the Forging of Steel IngotResearch on the Temperature Properties of Plate during the Laminar Cooling ProcessResearch and Improvement on the Rolling Force Model of PlateAnalysis of Transverse Wall Thickness Precision of Steel Tube Rolled by Semi-Floating Mandrel MillGeneration Mechanism of Micro/Nano Machined Surfaces Based on Molecular DynamicsA Model of Cutting Forces for Ball End Mill in High Speed MachiningSimulation and Experimental Investigation of Stiffness of the High Acceleration Linear Feed DrivesNumerical Simulation of ANSYS-LS/DYNA Induced by Double-Edge Ball Tooth Hob CutterResearch on Interpolation Algorithm of Three-Links Hybrid Machine ToolTransmission Ratio Analysis and Controllable Tooth Profile Modeling for the Nutation Drive with Double Circular-Arc External and Internal Spiral Bevel GearsA Method for Performance Evaluation of Transfer Line with Unreliable Machines and Finite Transfer-Delay BuffersClosed-Loop Identification and Composed Controller Design for Precise MachiningThe Process Planning Simulation of Multi-Axis Numerical Control Based on Virtual RealityRedesign of a Complicated Component of Auto Body Based on the Properties of TWBsApplication of Finite Difference Method in Billet Gradient Cooling Employed in Isothermal ExtrusionThe Strength Design and Check of Turbine Generator Based on FEA and Fatigue EvaluationOperation Mode for Personnel Integration in Manufacturing System Based on Product Life CycleMulti-Field Co-Simulation Research on Suspension System of Forging Manipulator Based on Virtual Prototype TechnologyCoupled Simulation of Plastic Part and Mold Temperatures in the Filling Process of Rapid Heat Cycle Injection MoldingFE Analysis of the Effects of Cutting Speed on Thermomechanical Responses of AISI 4142 Steel in High Speed CuttingA Mathematical Model for Predicting Residual Stresses in Pre-Stretched Aluminum Alloy PlateExact Optimization of Time, Cost and Quality in ManufacturingResearch on the Connecting Performances of 1/10 Taper Spindle / Tool-Holder for High-Speed NC MachineUsing Efficiency Function in Analyzing the Ability of Flatness Control for a Cold MillModeling of Mircrostructure Evolution in Directional Solidification of Ni-Based Superalloy Turbine BladeThermal Error Robust Modeling and Real Time Compensation Based on the GA-BPN Theory on a Vertical Machine CentreStability Margin Sensitivity Analysis of a Multi-Rotor System Geared by Spiral Bevel Gear PairsStructural Optimization of Non-Contact Vortex Negative Pressure CarrierA Hybrid Approach of ANN and HMM for Cutting Chatter MonitoringState Monitoring for Centrifugal Pump of PWR Based on HMM and SVMThe Influence of Interfacial Thermal Contact Conductance on Resistance Spot Weld Nugget FormationA Particle Swarm Algorithm for Assembly Sequence PlanningA Study of the Microstructure and Grain Size at the Welding Heat Affected Zone of an Industrial Pure AluminumInvestigation of Fixture Design Exploring Pre-Tensioning ForcesA New Miniaturized CNC Machine ToolA 3D Nonlinear Finite Element Study on Biomechanical Behavior of Dental ImplantsPerformance Assessment on Base-Isolated Smart Material-Structure System by Using Magnetorheological FluidsThe Effect of Bending Rigidity on Measuring the Adhesion Work of MembraneThe Novel Compound Evolutionary Optimization Algorithm with Hybrid Discrete Variables and its Application to Mechanical OptimizationDesign Optimization for Cold Forging by an Integrated Methodology of CAD/FEM/ANNResearch on the Simulation Method for I.C.E Structural Acoustic RadiationDeformation of Seat Support during Free-Cooling after EjectionAn Optimization Analysis of Prestressed Space Grid Structures Based on System ReliabilityKnowledge-Based Computer Aided Process Innovation MethodStrength Analysis of Planetary Trains? Carrier of EPB Shield MachineStudy on Boosting Curve for Electric Power Steering System Based on ADAMSCombining AST and Lock Techniques to Maintain Consistency of Multiple Objects in Replicated CAD EnvironmentsStudy on Injection Mold Rapid Design System Based on Parametric TechnologyFinite Element Static and Dynamic Analysis for a Piston4Ps Framework of Tooling Development and ManagementExperiment Study and Finite Element Analysis of the Failure for 75000 m3 Wet GasholderKBCADFW: A Knowledge-Based Collaborative Computer-Aided Design FrameworkA Multi Autonomic Objects Flexible Workflow and its Knowledge Acquisition Supporting Engineering Design ProcessThermodynamic Performance Simulation of Diesel EGR Cooler with Finned TubeDesign of a Horizontal Moving Mechanism for High-Speed & High-Acceleration StackersHybrid Optimization Approach for Gas-Assisted Injection Molding Based on Metamodeling and Particle Swarm AlgorithmResearch on Numerical Investigation and Test Verification of Brake Performance in a Hydrodynamic Tractor-Retarder AssemblyMechanics Design of Connecting Frame in Aircraft Composite CabinThree-Dimensional Thermal Analysis of Spherical Plain Bearings with Self-Lubricating Fabric LinerPartial Matching Algorithm of 3D CAD Models Based on the Constraints of Transition FeaturesVirtual Prototype Simulation of Vertical Clamp Kinematics and Dynamics for Operating SafetyA Multi-Agent Based Tool Path Planning Method for STEP-NC Compliant MillingVirtual Prototyping and Validation of an Automatic Washing MachineModal Analysis of Flexible Assembling Fixture for Aircraft Panel Component Research on the Rapid Slicing Algorithm Based on STL Topology ConstructionResearch and Realization of Digital Design System Wheel Loader Main Reducer Effects of Interference Fit and Preload on the Performance of Low-Speed Angular Contact Ball BearingThe Coding System for Automatic Injection Mold Integrated CAD/CAPPResearch on Collision Method for Irregular Mechanism Kinematics SimulationA New Type Adjustable Shock Absorber and its Characteristic ModelToolpath Algorithm for Complex Pocket on the Network OptimizationAccuracy Synthesis of a 3-PRS Parallel Manipulator Based on Genetic AlgorithmsA Kind of CAD/CAE Integrated Modeling Technology Based on FEATUREResearch on Structure Rationalization Method of Product Family and its ApplicationApplication of Kinematics Simulation Technology in Agricultural Machinery DesignComplicated Model Establishment and Second Development for Enterprises by MoldWizardA 3D Modeling System for Construction Work Simulation Based on Rendering and Dynamic Engines Parameterized Finite Element Analysis for Quick-Opening Supercritical Fluid Extraction KettlePerformance Prediction and Design Method for Centrifugal Pump Based on Computational Fluid DynamicsExtraction of Tiny Crack for Magnetic Ring Based on Wavelet Transform and Morphology Design and Analysis of MEMS-Based ActuatorResearch on Virtual Design and Simulation System for Manipulators of Multi-Degree of Freedom Research on Comfort Evaluation Method of Tool HandlesParticle Swarm Optimization with Adaptive Inertia Weight and its Application in Optimization DesignDynamic Analysis of a Rotatable Mobile Robot Based on Turning Pose Matching Technology of Point Cloud Models Based on Combination FeaturesResearch on Parameters Optimization of Virtual NC Milling Based on Parallelism Selection Genetic AlgorithmDynamic Load Sharing Characteristic of Planetary Gear System with Load Balancing MechanismOptimum Design of Roll RingOptimal Layout of the Irregular Parts with Neural Networks Hybrid AlgorithmResearch on the Three-Dimensional Elliptical Motion of Rotary Traveling Wave Ultrasonic MotorMulti-Attribute Evaluation and Optimal Selection Using Information AxiomDistributed Monitoring System of Multi-Machine Tools Based on Wireless Sensor NetworkTopology Design Optimization of Rib Layout in Box StructureDeformation of Flexspline under Transmission Force in Harmonic Drive Design of Precise and Efficient Synchronized Multi-Axis Control Servo SystemNumerical Study of Dynamic Response of Steel Deck Pavement under Traveling Random Vehicle LoadInvestigation on the Contour Curve of Straighter Roll by Conjugate Revolving Quadric TheoryDevelopment of the Dressing Software for Form Grinding Wheel Used for Grinding Involute Helical GearsStructure Design and Multi-Domain Modeling for a Picking Banana ManipulatorResearch and Analysis on the Mechanical Characteristics of Brush Shape Cleaning Element in Spiral InstallationSTEP-Compliant Knowledgebase in Support of Customized Product Development for SMEsNumerical Simulation of the Cooling Effect by Air Conditioner and Spraying in High-Temperature Working FaceKey Technology Research on Mould Heating System of Injecting MachineThe Effects of Normal Gap Distribution on Cathode Design of Aero-Engine Blades in Electrochemical MachiningSupplier Evaluation Based on Mobile Agent and Information CredibilityDecomposition-Based Modularity Method for Product Collaborative DesignMulti-Objective Optimization Design of Mold Platens on Large Precision Injection Molding MachinesThe HSM Cutters Management System Based on B/SA Structural Topological Optimization Method Based on Varying Displacement Limits and Design Space AdjustmentsReport Management in Performance Simulation for Complex Mechanical Product Arrangement Optimization of Instruments Based on Genetic AlgorithmDesign and Analysis of Horizontal Transfer System for Dual-Mode TrailerScatter Point Cloud Denoising Based on Self-Adaptive Optimal NeighborhoodExperimental Modal Analysis of CNC High Precision Surface Grinder with Horizontal Spindle and Rotary Table MGK7350Effective Treatment of the Simulation Analysis under some Complicated ConditionsStructural Dynamic Topology Optimization and Sensitivity Analysis Based on RKPMApplication of an Improved Shell Element in Springback AnalysisDevelopment of CAD/CAM Software System for Large Non-Regular Steel ConstructionsFire Protection Design for Steel Staggered-Truss Framing System Based on Mechanical Performance CalculationA New Computer Aided Design System of Belt ConveyorDynamic Characteristic Analysis of the Horizontal Machine CenterStudy on Rapid Variable-Type Design Method of Gantry Crane Based on TemplatesModeling and Control Method for Multi-Layer Distributed Flow Based on WFCP-NetVision-Based Two-Handed Interaction for Augmented RealityNumerical Simulation on the Airflow of Electric Cutting Tool Pattern Recognition for Control Charts Using AR Spectrum and Fuzzy ARTMAP Neural NetworkResearch on Multi-Process Route Decision-Making of Warm Forming for Projectile BodiesMultidisciplinary Collaborative Product Modeling in Distributed Network EnvironmentA Novel Discovery Technique on Attribute Weight of Engine CBR Design SystemA Design of Large-Scale Speed Modulation in Hydraulic Cylinder and its ApplicationApplying Fuzzy Neural Networks and Gray Theory to Construct a Modular Product Customization SystemDesign and Finite Element Analysis of Corrugated Plate Boarding BridgeThe Study of Mechanical Product Concept Design Method Based on Reverse EngineeringEffect Study on Deformation of Links to Error of Parallel ManipulatorStructural Analysis of Composite Shield Cutter-Head and Cutters Arrangement Optimization Based on Finite ElementFactors Effect on Vortex Torque of Aerostatic BearingsThe Effects of Different Defects on Buckling Behavior of Single-Walled Carbon NanotubesThe Study on Advancing Velocity of Hydraulic SupportCollaborative Commodity Design System Based on DARFADResearch on Machining Face Gears Using a CNC Hobbing MachineA New Architecture of LCD Driver of Rail-to-Rail Buffer with High Gain Wide RangePhase-Field Simulation of Three-Dimensional Dendritic GrowthEvaluation and Analysis of the Onlay Patellar Component in Total Knee ArthroplastyA Coupled Finite Element and Meshless Local Petrov-Galerkin Method for Large Deformation ProblemsVisual Computation of Thermohydrodynamic Lubrication of Dynamically Loaded Journal BearingsComputer-Aided Form Generation for Product DesignNumerical Simulation of Flow Field of Metro Train HeadReconstruction of Human Skeleton Model Using Reverse Engineering TechnologyResearch on Characteristic Microstructure and Properties of Fe20Ni3Mn Alloy Induced by Laser Shock ProcessingFormation of Periodical Sub-Micron Sized Structures on Silicon by Interfered Nanosecond Laser PulsesPicosecond Pulsed Laser Induced Melting of Monocrystalline Copper: A Hybrid SimulationInfluence of Laser Parameters on Precision in Hybrid Plasma Laser Deposition ManufacturingNumerical Simulation on 3D Residual Stress Field of Both-Side Laser Shot Peened Specimen with Center-HoleA Powder Shrinkage Model for Describing Real Layer Thickness during Selective Laser Melting ProcessEffect of Scanning Velocity on Surface Hardening for Ti Substrate by CO2 LaserStudy on the Factors Influencing the Layer Precision in Hybrid Plasma-Laser Deposition ManufacturingThe Investigation of Partial Penetration Lap Laser Welding Applied on Stainless Steel Railway VehiclesOptical Properties Characterization of Thermoplastics Used in Laser Transmission Welding: Scattering and AbsorbanceSpectrum Changes of Partially Coherent Polychromatic Beams in Laser ResonatorsResearch on Cladding Nickel on Copper Crystallizer Using Laser Metal Deposition TechniqueAnalysis of 7050 Aluminum Alloy Crack Growth by Laser Shock ProcessingSimulative and Experimental Study on Laser Compound Forming of PlateLaser Cladding of an In Situ Synthesized TiB and TiC Reinforced Titanium Matrix Composite Coating on Ti6Al4VOrthotropic Experiment Research on Bending Angel of Laser Shock FormingHigher Precision Forming by Laser Peening under Pre-Bending DieStudy on Chemical Mechanism of Laser and Fluid Corrosion Combining ProcessingAnalysis on Microstructure of Laser Brazing Diamond Grits with a Ni-Based Filler AlloyPitting Corrosion Behavior in Laser Weld Metals of 2205 DSS with Continuous Heat TreatmentInterfacial Microstructure and Phase Constitution of the Cu/Al Dissimilar Metals Joint Made by Contact Reactive BrazingLinear Friction and Electron Beam Welded Joints of Ti2AlNb/TC11Optimizing the RSW Process Quality of Auto-Body via the Taguchi Method and a Neural-Genetic ApproachEmbedment of HA into Superplastic Ti-6Al-4V: Effects of Implantation TemperatureMechanical Properties of Single-Walled Carbon Nanotubes under Large Axial DeformationStudy on Joint Residual Stress Induced by Laser Beam Welding of High Strength Automobile Thin SheetBond Thickness Effects upon Dynamic Behaviour in Adhesive JointsParametric Analysis Mechanical Properties of Bolted JointsMicroscopic Study on the Mechanism of Ultrasonic NanoweldingMechanical Behaviors of Self-Piercing Riveting Joining Dissimilar SheetsStudy on the Microstructure of Micro Laser Welded Joint of TiNi Shape Memory Alloy SheetDouble Metal Trimming Die Manufactured by Using Hardfacing MethodTheoretical Study on Stress State in Adhesive Layer of Single Lap Joint under Eccentric Tensile LoadThe Arc Sound Characteristic on MIG Weld PenetrationStudy on Fuzzy Controller of Welding Arc LengthMicrostructures and Mechanical Properties on Laser Welded Joints of Automotive High Strength Complex Phase SteelNumerical Simulation for the Thermal Fatigue of Flip Chip Solder JointsResearch on Laser Full-Penetration Welding In Situ TiB2 Particulate Reinforced ZL101 CompositesCharacteristics of Underwater Swirling Plasma Arc Cut QualityWeld Pool Shape Variations and Electrode Protection in Double Shielded TIG WeldingInvestigation of UV Light Intensity Distribution of Integral Micro-Stereolithography SystemResearch on Solidification Characteristics of Resin in High-Resolution Stereolithography SystemEffect of Corrosion Pillowing on Mechanical Properties of Lap JointDevelopment of a Novel Laser-Sintering Machine for Fabrication of Artificial BoneDevelopment of High Speed Scanning System for the Fabrication of 3D Metal Parts Using Electron Beam Selective Melting TechnologyPrediction and Research of Single Point Incremental Forming LimitDesign and Theoretical Analysis of Mini-Plunger Sprayer Used in SW2502 Fused Deposition Modeling SystemRapid Fabrication of Micro-Gear via Vacuum Casting Technique of Silicone Rubber MouldStudy on Fiber Laser Single Melting Track During Selective Laser FormingMicrostructure and Performance Characteristics of Parts Produced via GMAW Surfacing Rapid FormingExperimental Research of Process Parameters in Metal Droplet Deposition ManufacturingShaping Movement Analysis and Simulation of Ballscrew Manufactured by Cold RollingResearch on Patternless Casting CNC Manufacturing Technology and Development of the EquipmentProcess Research on the Laser Rapid Manufacturing TechnologyResearch and Application on Reverse Design of Complicated Petroleum AiguilleDual-Phase Materials Extrusion Process for Rapid Fabrication of Ceramic Dental CrownModeling and Analysis of NC Compliant Abrade Polishing for Surface of RevolutionCAD/CAE System for Shaping Process of Three Dimensional Complicated Surfaces in Electrochemical MachiningFuzzy Optimization Design on Stranded Wire Helical Spring of High-Frequency Vibration SieveGrinding Finishing Merging Electropolishing on Hole-Wall Surfaces Study on Optimization of Cathode?s Feeding Route in Flexible Feeding Electrochemical MachiningEvaluation of WEDM Surface QualityThe Research of Digital Soft Switching Arc-Welding InverterElectrochemical Machining of the Turbulated HoleInfluences of Polishing Tool?s Shape on Surface Roughness in Magneto-Rheological Finishing Fast Polishing of Single Crystal DiamondOptimum Geometrical Arrangement of Workpiece in the Ultrasonic Vibration Shoe Centerless Grinding Surface Roughness Characteristics of Fine ELID Cross Grinding for Silicon WafersChip-Ejection Mechanism and Experimental Study of Water Dispersant Dielectric Fluid on Small-Hole EDMFinishing Clearance Research on Magnetic Abrasive FinishingResearch of Uniformity and Effect on Crankshaft Barrel FinishingFinishing Effect and Uniformity on Gas-Particle Two-Phase Swirling Flows Finishing for Hole SurfaceSimulation and Experiment Research on the Swirling Airflow Compounded with Magnetic-Field FinishingStudy on Bio-Limited Forming Technology Based on Micro-Composite Sol-Gel Coating Study on the Conditions of Near-Field Acoustic LevitationThe Function of Magnetic Field in a Magnetic-Electrochemical Compound PolishingEffects of Polymer Particles Suspending in Dielectric Fluid on Surface Roughness of EDMSimulation of Particles Movement in Powder Mixed EDMStructural Analysis and Building an EDM Process ModelTemperature Field Model in Plasma Arc Forming of Laminated Clad Metal Sheets Containing DefectsHeat Absorbing Rate in Laser Drilling of YG8 AlloyGas-Liquid Combined Multiple Cut in High-Speed WEDMResearch on Hydroforming of Bimetallic Lined PipeNovel Jump Control for Debris Processes of Electrical Discharge Machining with Direct-Drive SpindleInfluence of Substrates and Annealing on the Al-Cu-Fe Nano FilmsElectrical Characteristics of Extended Gate FET Sensing Chip Constructed for Detection of DNAAnalytical Model of Unconstrained Nonlocal Higher-Order Nano-Plates for Bending Analysis
In Situ Nanoscale Deformation Studies on Micro Copper Wires Using Atomic Force MicroscopyA Multiscale Modeling Approach for Carbon Nanotubes Error Compensation in One-Point Inclined-Axis Nanogrinding Mode for Small Aspheric MouldSynthesis and Photoluminescence Properties of Novel SnO2 Zigzag Nanoribbons One-Point Nano-Grinding for Micro-Aspherical Glass Lens Mould Design and Research on a Novel NEMS Accelerated Sensor Based on GaAs PHEMT Fabrication and Structure Measurement of the Double-Barrier Nano Film Resonant Tunneling Gyroscope An Improved Thermal Type Microsensor with Thermal Isolation Microcracks An Improved Calibration Method for Optical 3D Measuring System Using Cross Target Based on Bundle Adjustment Algorithm Application of Pressure Test System in Dispenser for GasolineNew Method for Large-Scale Dimensional Metrology Using Laser Tracker System Study on the Technologies of Rapid Three-Dimension Optical Measurement for Welding Deformation of Sheet Materials Research on Mechanical Fault Identification Based on Improved SVMFabrication of Piezoelectric Thickness-Shear-Mode Acoustic Wave Sensing Device and its Application Evaluation of Measurement Uncertainty for High Precision Gear Involute Profile Measuring SystemInfluence of Specimen Sampling on Internal Residual Stress TestResearch on High-Precision Measurement Platform for Optical Aspheric Surface and Corresponding Error CompensationStudy on On-Machine Inspection Technology of Machining Center BasedExploration on Applying Non-Contact Photoelectric Detection Method for Double-Enveloping Hourglass WormOn Determination of Geometric Damage TensorHybrid Numerical-Optical Methods for Analysis of Mechanical StructuresIn Service Detection of 45 Steel?s Rotary Bending Fatigue Damage Based on Metal Magnetic Memory TechniqueTower Type Sensors for Monitoring Corrosion Risk in Cover-Zone ConcreteIntelligent Moisture Controlling System for Molding SandThe Technique of Online Measurement and Data Processing for Aspheric MachiningCalibration and Registration for Inspection Robot with Contact ProbeDevice and Method for Large Size Aspheric MeasurementExperimental Modal Analysis of Roller Gap Sensor Structure on Hot Rolling Mill Development of Novel High Precision Angular Displacement SensorPost-Weld Quality Inspection for CO2 Laser Tailored Blank Welding with Vision SensorThe compact Platform for In Situ Nanoindentation and Scratch TestVisual Integrated Measurement on Geometry Parameters of Circular Saw BladeResearch on Measuring Path and Surface Fitting Algorithm for Non-Axisymmetric AsphericResearch on Quality Evaluation System of Dynamic Alliance Based on Life-Cycle Study of Simulation Tester for Key Rubbing Pairs in Internal-Combustion Engine Detection of Unbonds in Honeycomb Sandwich Structure Using Lock-In ThermographyThe Design of VI-Based Synthesized Testing System for Belt ConveyorsFast Location of Thermal Target with Low Offset and Spatial Filter of Winner-Take-All CircuitCharacteristics Identification of Overlapping Vibration Signals on MallatStudy on the Disturbance of Rotor-Bearing System Caused by Circumferential Loading TorqueStudy on the Measuring System of the Planar Parallel Micro-Motion Worktable?s Location and OrientationSurface Roughness Pattern Measurement of Tensile Specimen by Using Digital HolographyThe Finite Element Analysis of the End Anchorage under Larger Prestressing Load in Rehabilitation EngineeringResearch on Decision-Making Model for Mechanical Motion SchemeThe Study on Optimal Matching of Power System of Hybrid Hydraulic TLTStudy on Edge Detection Technique in Material Bag ImageThe Design of New Type Muffler Used For Steam Turbine?s Exhaust Device Reliability Analysis of Prestressed Steel Structure in Regards to Temperature ActionThe Design of Mechanical System for Harbor Basin Wave MakerProduct Development Oriented Knowledge Management Exploiting Critical Path Method for Evaluation of Conceptual DesignEfficiency- Reinforcement Technology Study for Hydraulic Reciprocating Sealing Based on TRIZ S-Field AnalysisThe Principle Studies of Series Multistage Axial Ram Pumps and the Fluctuation Analyses Structure Buckling Non-Probabilistic Reliability Index Calculation of Ventilated Supercavitating VehiclesThe Analysis of Failure Induced by Manufacturing Defect in Cu-30Ni Alloy Condenser Tube to Improve the Finished ProductDetection of Small Damage of Beam Structures Based on the Slope of Proper Orthogonal ModeFuzzy Pattern Recognition of Steelmaking Process for ConverterStudy on Impinging Streams Reactor for Sewage PurificationAnalysis on Cutting Ability of Picks on Continuous MinerNew Type of Cantilever Crane for High-Speed Railway Track Plate ConstructionsStudy on a Capacitive Micro-Mechanic GyroscopeDevelopment of the Self-Adaptive Pipeline Cleaning RobotSelf-Adaptive Suppression of the Euler Beam Remnant Vibration Using the Interior Inlay Viscous Fluid Unit Method Research on Tempering Process of LZ20Mn2 Seamless Pipe for AxleStudy of a Novel Approach of Active On-Line Balancing Device for High-Speed Spindle SystemResearch on Fatigue Damage of Ferromagnetic Material by Metal Magnetic Memory MethodsAnalysis of the Hydrodynamic Effect in Laser-Textured Mechanical Seal FacesThe Realization of Monitoring System for Stacking Crane Using Plotting Finite State MachineSimulation and Experiment for Rigid and Flexible Wings of Flapping-Wings Microrobots A Passivity-Based Approach to the Rotor Resistance Estimation and Sliding Mode Control for Induction MotorsTri-Objective Optimization in Production Based on Stochastic PrincipleEffect of Grinding Wheel Diameter Change on Geometrical Parameters of Ball-Nose End Mill Dynamic Analysis on Noise and Vibration Study of Flexible Wiper Blade System