5-vols. Set.
Buch, Englisch, 4720 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 10000 g
ISBN: 978-0-87849-280-0
Verlag: Trans Tech Publications
Autoren/Hrsg.
Fachgebiete
Weitere Infos & Material
Committees
Preface
CHAPTER 1: Semiconductor Materials Manufacturing
Blade Diamond Disk for Conditioning CMP Polishing Pad
Three-Point Bending Test Behaviour of a QFN Semiconductor Package
Structural and Optical Properties of Dy Doped ZnO Film Grown by RF Magnetic Sputter
The Progress of Fixed Abrasive Wire Saws in the Last Decade
Photocatalytic Analysis and Characterization of Zn2SnO4 Nanoparticles Synthesized via Hydrothermal Method with Na2CO3 Mineralizer
An Optimization of Two-Steps Curing Profile to Eliminate Voids Formation in Underfill Epoxy for Hi-CTE Flip Chip Packaging
The Crystal Structural Properties of Sputtered ZnO Films Containing Internal Stress
The Comparison Research of Two Working Electrodes in Electrochemical Reduction of Silicon Tetrachloride
Effect of Ca Content on Mechanical Properties of 4N Gold Wire for Quad Flat Nolead (QFN) Stacked Die Package
Characterization of 0.5 µm BiCMOS Gate Oxide Using Time Dependent Dielectric Breakdown Test
Dynamic Analysis of Optical Brittle Crystal Slicing by Using Wiresaw
CHAPTER 2: Precision Molding Processes
On the Warpage in the Lower Case of Lead-Acid Batteries
Effect of Forming Parameters on the Mechanical Properties of Thixomolding AZ91D Magnesium Alloy
Analysis on Transmission Characteristics of New Axis-Fixed Cycloid Gear
Research on the Key Technologies for New Large Dual-Platen High-Precision Clamping System
CHAPTER 3: Materials Forming
Analysis of Tension and Deformation Curvature in Strip Tension Levelling
The Modulus Mensuration of Yada Model and the Microstructure Simulation of Casting AZ31 Magnesium Alloy
Strip Shape Analysis of Asymmetrical Cold Rolling of Thin Strip
Experimental Research on Coaxial Extrusion of GF/Pb Complex Wire
Numerical Simulation of Push-Bending Process of Aluminum Section Profile
The Effect of Entrance Temperature on Texture and Microstructure Development in Cold Mill Rolled 85/15 a-Brass
Numerical Simulation and Process Test for Cold Extrusion of Wheel Hub Bearing Rings
Effect of Bonding Pressure on Transient Liquid Phase Bonding Joint Microstructure and Properties of T91/12Cr2MoWVTiB
Finite Element Simulation of Backward Ball Spinning of Thin-Walled Tube with Longitudinal Inner Ribs
On Spontaneous Austenite Recrystallization of Low Pressure Rotor Steel 26Cr2Ni4MoV
Research on Intelligent Deep Drawing Technology of Sheet Metal
New Methodologies for the Determination of Precise Forming Limit Curve in Single Point Incremental Forming Process
A New Springback Compensation Method for Sheet Metal Bending Based on Curvature Correction
Thermo-Mechanical Numerical Simulation on P91 Closed Upsetting Process
Influence of Hot Working Conditions on Mechanical Properties and Microstructures at Weld Zone of the Ti3Al /TC4 Dual Alloy
Study on Work Hardening Performance of Pure Shearing Fine-Blanking with Negative Clearance for ASTM-Gr.D and ASTM-1022 Steel
Study on the Impact of Fine-Blanking with Negative Clearance on the Materials Microstructure and Hardness
Influence of Isothermal Forging Temperature on Microstructure and Tensile Properties of Ti-5.8Al-4.0Sn-4.0Zr-0.7Nb-0.4Si-1.5Ta Near-a Titanium Alloy
Numerical Simulation on the Effect of Process Parameters for Incremental Sheet Forming
Determination of Winding Tension in Manufacturing Strip Wound Die
Study on Deformation Mechanism of Tube Hydropiercing
An Investigation of Fineblanked Surface of Cold-Rolled 45 Steel
Simulation and Analysis on Microstructure Evolution of Large Generator Retaining Ring during Multi-Fire Forging
Preparation and Characterization of Well-Dispersed Nd1.6Eu0.4Zr2O7 Solid Solution and its Fluorescent Behavior
Ultra-Fine Grained Fe-32%Ni Alloy Processed by Multi-Axial Forging
Comparative Study of the Process Fracture between Fine-Blanking with Negative Clearance and Conventional Blanking
The Influence of Integrated Strength on Bulging Cracking of Tailor Welded Blanks
Advanced High Strength Steel Sheet Forming and Springback Simulation
Improving Plastic Thermoform Quality with Uniform Heating Technology
Numerical Investigation of Viscoelastic Flow and Swell Behaviors of Polymer Melts in the Hollow Profile Extrusion Process
The Design Method of Punches and Dies for Progressive Die of Motor Core Based on Association Design Technology
Solution of Singularity Points in Strip Rolling by Rigid Plasticity Finite Element Method
Effect of Ultrasonic Wave on Melt Foaming Process of Aluminum Foam
Study on the Differential Thickness Ratio Effect on Formability of TWB Based on Numeric Simulation
Research on Stamping of Aluminum Alloy Hemispherical Components Based on Numerical Simulation and Experiments
Extrusion Modeling of Solid Plug Flow of Co-Rotating Twin Screw Pulping Extruder
Optimum Design on Trapezoidal Thread Parameters of Co-Rotating Twin Screw Extruder
Research on Stamping Spring-Back Prediction for Car Body Panel Based on BP Neural Network
Investigation on Thermomechanical Treatment of PM FGH4096 Superalloy
Investigation on the Formability of Tailor-Welded Blanks
Springback Prediction of Axial Symmetry Sheet Part Drawing
Research of Geometric Parameters Related to TRB Uniaxial Tension
Development of CAD System and Forming CAE of Porthole Extrusion Moulds for Hollow Aluminum Profile
Study on the Dynamic Behaviors of X70 Pipeline Steel by Numerical Simulation
Numerical Analysis on Hot Stamping of B Pillar Reinforcement of Automobiles
Fatigue Life Prediction of Isothermal Forging Dies Based on Average Strain Method
Hot Deformation Behavior and Hot Processing Map of P92 Steel
Limit Pressure of Rupture Discs Found on Tensile Instability Condition
The Effect of Isothermal Forging Parameters on the Microstructure and Properties of Ti-5Al-5Mo-5V-1Cr-1Fe Titanium Alloy
Investigation of the Relationships between Billet Reheating and Semi-Solid Die-Casting
The Forming Scheme of a Silencer Cover in Progressive Die
Numerical Analysis and Optimization of Stamping Technology for Electrical Motor’s Cover
Plastic Deformation Characteristics Analysis in Rotary-Draw Bending Process of Thin-Walled Rectangular Tube
Microstructure and Mechanical Properties of Heavy Gauge Plate by Vacuum Cladding Rolling
Manufacture of a Seal Flange with E-Cross-Section
Temperature Effects of ECAP and Annealing after ECAP on Microstructure of TA15 Alloy
Study on Bending and Upsetting Forging 305 Marine Crankshaft
Improvement of Hole Flanging Product Forming Process Using Finite Element Simulation
An Analytical Solution to Metal Plane Problem in Terms of Orthotropic Anisotropy and Strain Hardening
Numerical Simulation and Experimental Study on the Weld-Line Movement of Tailor-Welded Blank
Spinnability of Semi-Continuous Casting 7A09 Aluminum Alloy
Electromagnetic Field Simulation and Experiment of Electromagnetic Forming of Magnesium Alloy Tube
Key Technology and Development on Side Pattern CAD/CAM on Mould for Auto Lamp
Hot Deformation and Processing Maps of a High Strength Alloy Steel
Effect of Process Parameters on Microstructures of 30Mn20Al3 Steel
Experimental Study on Csf/AZ91D Composite Using Extrusion Following Vacuum Infiltration Method
Synthesis of Intermetallic Ni3Al Alloy: Properties and High Temperature Oxidation Behaviour
Key Technologies in the Design of a Vacuum Die Casting Mould for Aluminum Alloy Joints
Finite Volume Simulation and Multi Parameters Optimization on Extrusion of Complex Aluminum Profile
FVM Simulation of Large Deformational Aluminum Extrusion Process and Die Bearing Optimization
Numerical Simulation and Evaluation of Local Thickness Increment in Ironing by Finite Element Method
A New Manufacturing Method for a Screw-Threaded Fuel Filler Pipe
Experimental Study on the Deformation of Oxide Scale and Friction during Hot Rolling of Stainless Steel 304L
Mechanical Properties and Microstructures of Ferritic-Rolled High-Strength Interstitial-Free (IF) Steel Sheets
Establishment and Application of Forming Limit Diagram of Multi-Gauge Laser Tailor-Welded Blanks
CHAPTER 4: Materials Behaviour
Effect of La and La+Sr on Structure and Properties of ZL101A
Effects of Shot-Peening on Cr-Rare Earth-Boronizing at Low Temperature for Medium Carbon Steel
Bifurcation and Chaos of a 4-Side Simply Supported Rectangular Thin Electro-Magneto-Elastic Plate in Many Fields
Investigation on Low Cycle Fatigue Life of SC Notched Specimens
Effect of Reactive-Al2O3 Addition on the Pore Size Distribution and Thermal Conductivity of Carbon Blocks for Blast Furnace
The Research on Process of Deep Cryogenic Treatment for W4Mo3Cr4VSi HSS Drill
Effects of Nb Doping on Dielectric and Ferroelectric Properties of Bi4Ti3-xNbxO12+x/2 Ceramics
Statistical Analysis of the Effect of Na2CO3 as Additive on the Reduction of Vanadic-Titanomagnetite-Coal Mixed Pellets
Study on Crack Retardation with the Consideration of Crack Surface Roughness by FEM
Effects of Mg-Doping on Structure and Electric Properties of MgxZn1-xO:Al Ceramics
Frequency Equations of Magneto-Thermoviscoelastic Surface Wave
Probabilistic Crack Propagation Behavior of Railway B Grade Steel
Microstructure and Mechanical Properties of Cast Ti25Nb3Mo3Zr2Sn Alloy
Creep Behavior of an AZ91 Magnesium Alloy Reinforced with Aluminum Silicate Short Fibers
The Effect of Precipitates on Anisotropy of Al-Li Alloys 2090 and 2090+Ce
The Characteristics of the Magnetic Memory Signals under Different States for Q235 Defect Samples
Dielectric Tunable Properties of Ba0.6Sr0.4TiO3 Thin Films with and without LSCO Buffer Layer
Activated Carbon Fiber for Super-Capacitor Electrode
Analysis of Fracture Failure of Diaphragm of Non-Contact Electronic Horn
Surface Hardness Changes after Strengthening under Low-Amplitude Loads
Compressive Response of UHMWPE/Vinyl Ester 3D Orthogonal Woven Composites at High Strain Rates
Effect of Silica Sol on the Properties of Unfired Mullite Rollers
The Study on Oxidation Resistance Properties of Ductile Cast Irons for Exhaust Manifold at High Temperatures
A Plastic Zone Equation Based on Mean Yield Criterion
Studies on Corrosion Behavior of Q235 Steel by Iron Bacteria in Sedimentary Water from Storage Tank
Mutual Interaction of Two Rail Surface Cracks under Thermo-Mechanical Contact Loading
Effect of Metal Powder on Blast Power of the Low Collateral Damage Ammunition
Influence of Perlite Admixture on Pore Structure of Cement Paste
Research on the Mechanism of Aging of Dual Phase Steel Produced by Continuous Annealing
Strain-Induced Precipitation in Nb-Bearing Low Carbon Multi-Microalloyed Steel
Influence of Plastic Deformation Degree on Microstructure and Mechanical Properties of the Magnesium Alloy ZK60 after T5 Treatment
Simulation and Analysis during Conveyor Stop Process Based on AMESim
A Study on the Characteristic of th
