Selected, peer reviewed papers from the 1st International Materials, Industrial and Manufacturing Engineering Conference (MIMEC 2013), December 4-6, 2013, Johor Bahru, Malaysia
Buch, Englisch, 276 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 630 g
ISBN: 978-3-03835-183-2
Verlag: Trans Tech Publications
Autoren/Hrsg.
Fachgebiete
Weitere Infos & Material
Electrochemical Self-Assembly of ZnO Nanosheetlike StructuresLubricity of Palm Fatty Acid Distillates at Various Rotational SpeedsInSe Nanothin Film with Ar-Gas Low Vacuum PressureThermoluminescence Properties of Optical Fibers Doped with RE+3 (RE=Sm, Nd) Ions Subjected to X-Ray IrradiationEffect of Fiber Loading on Tensile Properties of Cocoa Pod Husk Fibers Reinforced Thermoplastic Polyurethane CompositesNatural Clinoptilolite and Chabazite as Carrier for Antibacterial Agents of Cetylpyridinium Chloride (CPC) and SilverEffect of Melt Temperature on the Interfacial Thermal Resistance and Solidification Behaviour of Al/SiCp CompositesPreparation and Tribological Performance of Silica/Ethylene-Octene Copolymer NanocompositesAntibacterial Properties of Guided Bone Regeneration Membrane for Periodontal ApplicationsSelective ZnO Nanorods Hydrothermal Growth through Resist Patterning MethodEffect of Heat Treatment on Tensile Strength and Microstructure of AZ61A Magnesium AlloyA Simple and Cost-Effective Method for Fabricating Chitosan-Filled Filter Media from Lignocellulosic BiomassBiofilm Green Packaging: Characterization and Biodegradation StudiesPyrolysis of Solid Palm Waste Biomass with Microwave Absorber under Microwave IrradiationPreferred Growth Orientation of Cementite Carbide by Phase-Field SimulationA Review of the Low-Temperature Degradation of Dental ZirconiaMechanical Properties of Polylactic Acid/Treated Fermented Chitin Nanowhiskers BiocompositesPhase Evaluation of Pure Mg, Mg-1Ca and Mg-1Ca-3Zn ?Alloys by Thermal Analysis Used in ?Medical ApplicationsPhoto Catalytic Reduction of Pb(II) Using Titanium Oxide PVA-Alginate Beads under SunlightAluminum-Copper Bilayers Thin Films Deposited at Room Temperature by RF Magnetron SputteringParameter Study of Tool-Laminate Interface through Simulation for Composite Manufacturing Using Autoclave ProcessDesign and Verification of the Parameters of Hot Forging of Ti10V2Fe3Al Alloy CompactsSimulation of Automotive Galvanized Steel Stamped Parts: Experimental and Numerical ApproachResponse Prediction of Static Modal Testing on Milling Machine ToolTop Spray Fluidized Bed Granulated Paddy Urea FertilizerReduction of Rejection Rate for High Gloss Plastics Product Using Six Sigma MethodExperimental Investigation on the Use of Bispectral Analysis in Detecting Nonlinear Faults in Hydraulic MachinesExperimental Investigation on Dynamic Characteristics of Polypropylene Honeycomb Sandwich Structures under the Influences of Different TemperaturesR-Curve Modelling of Mode I Delamination in Multidirectional Carbon/Epoxy Composite LaminatesFracture Characteristics of Shear Adhesive Dissimilar JointSpringback-Free Sheet Metal Structural Part Design by Topography OptimizationOptimization of Spot-Welds on Patchwork Blank for Hot Forming ProcessCrush Characteristics and Energy Absorption of Thin-Walled Tubes with Through-Hole Crush InitiatorsInvestigation of Annular Gap Size for Optimizing the Dynamic Range of MR Damper Using Comsol Multiphysics SoftwareOptimization of Surface Roughness in Electro Chemical MachiningEvaluating the Effect of Main Factors in Manufacturing Production Line Based on Simulation ExperimentMorphological Investigation of Alumina Asymmetric Membrane by Manipulating the Sintering Temperature ProfileHydraulic Stability of Interlocking Concrete Unit-V (ICU-V)Cyclic Cohesive Zone Model for Simulation of Fatigue Failure Process in Adhesive JointsMicrowave Thermal Conversion of Oil Palm and Related Biomass for Biofuels and BiocharsEffect of Pitting Corrosion on Strength of AISI 410 Stainless Steel Compressor BladesDevelopment of Road Safety Sustainability Model for Malaysian RoadDesign of Supplier Selection Procedure in Garment CompanyImprovement of Work System with Ergonomic Approach of Domestic Shoe Industry in Cibaduyut BandungAn Analysis of Key Factors for Quality Practices in the UAE?s IndustryImproving Productivity in a Bank System by Using Computer SimulationApplication of Statistical Taguchi Method to Optimize Main Elements in the Residential Buildings in Malaysia Based Energy ConsumptionSupplier Selection Problem: A Multi-Objective Model Considering both All-Unit and Incremental Discounts with Multiple-ItemKnowledge-Based Genetic Algorithm for Multidimensional Data ClusteringInterdependency of Cleaner Production and Cleaner Application: Towards an Integrated Assessment on Appropriate TechnologyDevelopment of Supply Chain Management Practices and Competitive Advantages in Manufacturing Industries: A ReviewApplications of Cubic Motion Curve
