Sonstiges, Englisch, Band Volume 619, 412 Seiten, Format (B × H): 125 mm x 142 mm, Gewicht: 200 g
Sonstiges, Englisch, Band Volume 619, 412 Seiten, Format (B × H): 125 mm x 142 mm, Gewicht: 200 g
Reihe: Applied Mechanics and Materials
ISBN: 978-3-03795-901-5
Verlag: Trans Tech Publications
The 71 papers are grouped as follows:
Chapter 1: Thermal and Mechanical Research, General Mechanical Engineering,
Chapter 2: Tools and Electrical Engineering,
Chapter 3: Mechatronics and Robotics,
Chapter 4: Control and Automation,
Chapter 5: Information Technologies, Data and Signal Processing,
Chapter 6: Industrial Engineering
Autoren/Hrsg.
Fachgebiete
- Technische Wissenschaften Technik Allgemein Mess- und Automatisierungstechnik
- Technische Wissenschaften Sonstige Technologien | Angewandte Technik Signalverarbeitung, Bildverarbeitung, Scanning
- Technische Wissenschaften Maschinenbau | Werkstoffkunde Maschinenbau
- Technische Wissenschaften Energietechnik | Elektrotechnik Energietechnik & Elektrotechnik
- Mathematik | Informatik EDV | Informatik Angewandte Informatik Computeranwendungen in Wissenschaft & Technologie
- Technische Wissenschaften Maschinenbau | Werkstoffkunde Technische Mechanik | Werkstoffkunde
- Technische Wissenschaften Technik Allgemein Computeranwendungen in der Technik
Weitere Infos & Material
Prediction the Springback in Air-Bending Process Using Neural Network MetamodelDynamic Equilibrium Configurations of Multibody SystemsWear Behaviour of Stellite 6 Coatings Produced on an Austenitic Stainless Steel Substrate by Laser Cladding Using Two Different Heat InputsInfluence of Pipe Diameters on Shapes of Air Taylor Bubbles in Small Pipes Containing Stagnant WaterOn the Use of Composite-Steel Joint for Semi-Monocoque Frame DesignInfluence of Blast Wave on Behavior of Steel PlateThe New Rolling Mill Gearbox Concept DesignNumerical Analysis for Resistance Calculations of NPL as a Floating Hull for Wave GliderDesign of a Simple Underactuated Mechanical GripperEvaluation of the Performance of Micro-Drills in Drilling a Machinable Ceramic MaterialParametric Optimization in Turning of CFRP (Epoxy) Composites: A Case Experimental Research with Exploration of HS AlgorithmNET3D Calculation on the Depth of Penetration by a Long-Rod Penetrator with Varying ObliquitySimulation on the Life Expectancy of Fine Blanking Punch for Recreation Vehicle Seat Recliner Sector ToothUtilization of Tooth Contact Pattern in a Gear Meshing Model for Estimation of Sliding Loss in a Parallel-Axis Gear PairField Investigation on Thermal Performance of the Tile VentilatorComputer Aided Design of the Die-Set for Sheet Metal Punching and Blanking DiesA Hybrid Approach for Process Optimization in Taper Cutting Operation Using Wire Electrical Discharge MachiningOptimization of the EDM Parameters on Machining Ti-6Al-4V Alloy with Multiple Quality CharacteristicsTransient Radiation Coupled With Conduction Heat Transfer in a One Dimensional SlabThermodynamic Analysis of Hydrogen Production from Methanol Reforming in Supercritical WaterA CAPP/CAD for Sheet Metal Deep DrawingThe Effect of Rise Angle of V-Hull Non Ballast Ship on Resistance PerformanceSynthesis of Rigid-Body Guidance Mechanism with Path and Pose Generation IndependentlyThe Effects of Injection Timing on BDF in an IDI Diesel EngineHeat Transfer Enhancement due to V-Shaped Perforated Blocks in a Solar Air Heater DuctThe Performance of the Interlocking Block Solar CollectorSOx Reduction by Feedwater in an Industrial BoilerDevelopment of an Oscillating Drum Granulator Prototype for Cassava PearlOptimization of the Thrust Ripple of a Tubular Flux-Switching Permanent Magnet Linear MotorDesign, Fabrication and Evaluation of a Novel Electro Thermal Micro-Gripper for Handling of Head Gimbal Assembly2x2 Rectangular-Slot Microstrip Array Antenna for WLAN ApplicationsAn Effective Implementation of the Nonlinear Homotopy Method for MOS Transistor CircuitsParallel-Connected High Voltage Multiplier with Symmetrical StructureElectrical Energy Conservation in Engineering Industry: A Case StudySpace Frame Analysis, Design, and Testing for Electric Vehicle FormulaEffect of Grain Size on Effective Permittivity of Ferroelectric Films Based on Effective Medium TheoryMechanism Design and Manipulating Algorithm for Orientation Changing Module with Three Flexible LinksAn Innovative Motion Planning for 4-DOF PKMAn Altitude Estimation Technique for Autonomous Landing of a Quad-Rotor Using a Vision SystemDexterity Measures for 4DOF Exoskeleton RobotWeld Bead Tracking Control of a Magnetic Wheel Wall Climbing Robot Using a Laser-Vision SystemImplementing Expandable Path for an Resizable CobotA ?P-?C-FPGA Synergy Controller for a Linear Delta RobotThe Performance of a Delta TelerobotDesign Morphological Changing All-Terrain-Rover and Optimizing with Genetic Algorithm for Enhancing MobilityA Low-Cost Stereo Vision System for Real-Time Pose Estimation and its Application for Robot TrackingA Study on Mobile Gait Rehabilitation Training RobotsA Weighting Slope MPPT Method Based on Sun Tracking Applied in PV SystemExperiment of the State Variable Feedback for a QuadrotorVibration Rejection and Stabilization Control for an Inertial Stabilization SystemStudy on Dynamic Characteristics of DC Valve in Electro-Hydraulic System Using CFD SimulationGain-Scheduled Control Approach by Logarithm Transformation for Electrical Vehicle Traction Force ControlEvaluation of Deadband Effect in Steer-by-Wire Force Feedback System by Using Driving SimulatorA New Stator Flux Estimation Method for Direct Torque Control of Electrical Excitation Flux-Switching GeneratorTracking Control for the Center-of-Gravity Constant Shift of Omnidirectional Rehabilitative Training WalkerProcess Control Virtual Laboratory: Temperature Control Based on LabVIEW for Convection Heat TransferImproved SPIHT Algorithm for Texture Image Compression10.3125Gbps High-Speed SFP+ Channel Signal Integrity EvaluationsA New Analytical Approach to Estimate Fading in Mobile Communication System DesignDriver Behavior Detection Based on Multi-GNSS Precise Point Positioning TechnologyComplex Network Based Modeling and Analysis of Resource Nodes for MGEvaluating the III-Posedness of Inverse Problem to Size Flaws from Eddy Current NDT Signals Obtained with an Absolute Type ProbeLow-Complexity Multiplication Using Complement and Signed-Digit Recoding MethodsComparative Study on Wear Particle Colour Classifications Using Various Machine Learning AlgorithmsDesign and Implementation of Linux-Based Supervisory and Control Configuration Software for Automatic Billet Cut-to-Length SystemModeling for Materials and Logistics Optimal System in JIT Flexible ManufacturingA Study of a Single-Period Model for the Parallel Fleet Replacement ProblemEco-Driving Rating Based on Average Trip Speed and EvaluationPalm Oil EFB: Green Energy Source in MalaysiaApplying Kalman Filter for Correlated Demand ForecastingFuzzy-TOPSIS for Appropriate Site Selection for Establishing a Thermal Power Plant
