Buch, Englisch, 724 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 1180 g
Buch, Englisch, 724 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 1180 g
ISBN: 978-3-03835-097-2
Verlag: Trans Tech Publications
Autoren/Hrsg.
Fachgebiete
Weitere Infos & Material
Preface and Conference Organizers
I. Material Science and Processing
A Structure and Morphology of Nanocomposites Composed of Carbon Nanotubes with a Varying Fraction of Platinum Nanoparticles
Analysis of Influence of Aluminum Content on Inclusion Characteristic and Fatigue Life of Bearing Steel Using Statistics of Extreme Values
Deformation Behavior of Adhesive Layer in Stretch-Bending/Unbending for Adhesively Bonded Sheet Metals
Deformation Behaviour of TRIP Steel Monitored by In Situ Neutron Diffraction
Deformation Evolution of a Zr-Based Bulk Metallic Glass under Three-Point Bending Tests
Effect of Interference-Fit on Fatigue Life for Composite Lap Joints
Effect of Temperature on Cyclic Behavior of AZ31 Mg Alloy Sheet
Effects of Scoring Depth, Tracking Angle, Rubbering on Bending-Moment Relaxation of Creased Paperboard
Harmonic Structure Design of Co-Cr-Mo Alloy with Outstanding Mechanical Properties
New Design of Aluminium Based Composites through Combined Method of Powder Metallurgy and Thixoforming
Research of Large-Area Electrical Discharge Machining for Insulating Si3N4 Ceramics with the Assisting Electrode Method
Role of Halloysite Nanoparticles and Milling Time on the Synthesis of AA 6061 Aluminium Matrix Composites
Tensile Properties and Microstructure of Joined Vacuum Die Cast Aluminum Alloy A356 (T6) and Wrought Alloy 6061
Processing of Epoxy-Nickel Matrix Composites Reinforced with Aluminum and Waste Elastomers
Wear Resistance of Elastomeric Based Composites by Continuous Multi-Cycle Indentation Used in Manufacturing Engineering
New Design of Composite Materials Based on Scrap Rubber Matrix Reinforced with Epoxy and SiC
YSZ-Reinforced Mg-Based Amorphous Composites: Processing, Characterisation & Corrosion
Search for Rapid Quality Control of Ni-Cr-Mo Low Alloy Steels Using Multifaceted Approaches for Fracture Toughness Estimation
Shaping Porous, Low Density Al Composites by AWJ Cutting Process
Tensile Property of Electrochemically Polished Titanium Alloy
The Effect of Particle Deformation on Densification of 316L Stainless Steel under Micro-FAST
II. Advanced Machining
Application of Electrochemical Discharge Machining to Micro-Machining of Quartz
Application of Idling Stop Technology for Servo Motors in Machine Tool Operations to Reduce Electric Power Consumption
Applications of Optical Path Length Compensation Technology for High Power CO2 Laser Cutting Process
Bonding PDMS Microfluidic Devices to PMMA and Glass Substrate Using Pulsed UV Laser Technology
Finite Element Modeling of the Effect of Tool Rake Angle on Cutting Force and Tool Temperature during High Speed Machining of AISI 1045 Steel
Investigation of Chatter Vibration in End-Milling Process by Considering Coupled System Model
Micro Cutting of Biliary Stent with Nanosecond Fiber Laser System
Temperature Distribution of Micro Milling Process due to Uncut Chip Thickness
The Use of Supports to Fast Fabrication of Plastic Parts
Effect of Optical Properties Characteristic Polymethylmethacrylate Using UV Laser Direct-Structuring
III. Geometry Analysis and Forming
Effect of Punch Surface Topography on Friction in Micro Combined Forward and Backward Extrusion of Brass
An Analytical Model for Deformation Path Design in Multistage Incremental Sheet Forming Process
Effect of Edge Shape of Tool in Finish Blanking
Forming Limits of Several High-Strength Steel Sheets under Proportional/Non-Proportional Deformation Paths
Stiffness Improvement of Stamping Die by Means of Topology Optimization
Study on Step Depth for Part Accuracy Improvement in Incremental Sheet Forming Process
IV. Forming Processes
Bulging Investigation of Cylinder Compression Forming Using Upper Bound Analysis
A Study of Hole Flanging-Upsetting Process
Comparison of Cast and Extruded Stock for the Forging of AA6082 Alloy Suspension Parts
Effect of Counter Punch Pressure on Springback of High Strength Steel Sheet
Experimental Study and Efficient Prediction on Forming Forces in Incremental Sheet Forming
Incremental Sheet Forming (ISF) of AISI 316 Stainless Steel Sheet Using CNC Milling Machine
Influence of Pre-Generated Infinite Adhesive Defects on the Forming Behaviour of Adhesive Bonded Steel Sheets
Influence of Wire Reinforcement on the Forming Behaviour of Adhesive Bonded Steel Sheets
Influences of Process Conditions on Stretching Characteristics of Crystalline Polymer Film
Precision Glass Molding of High Filling Factor Micro Lens Arrays
Research on Formability of Aluminum Alloy Automotive Panels by Using Viscous Pressure Forming
Springback of Aluminum Alloy Sheet Metal and its Modeling
Theoretical and Experimental Studies on the Influence of Process Parameters on Strains and Forces of Single Point Incremental Forming
Verification of Numerical Roll Forming Loads with the Aid of Measurement Equipment
On Flow Layer Uniformity in the Co-Extrusion of Polymer Multilayer Film
V. Forming with Temperature Influence
Development of Looper Shape Meter and Verification Test Results in Hot Rolling
Direct Thermal Method of Aluminium 7075
Effect of Heating on Springback in Heat Assisted Microbending
Flow Stress and Pyroplastic Behaviour of Ultra-Low Carbon Steel in Warm Temperature Range
Influence of Cooling Conditions on Forming Performance of Hot Stamped and Press-Quenched Steel Sheet Part
Thermomechanical Forming of NiTi Shape Memory Alloy Wire
Design and Test of a Rapid Thermal Annealing Furnace for Improving Surface Properties of Silicon Brick in Multi-Wire Sawing Process
VI. Surface and Precision Engineering
A New Approach to Calibration of Printed Circuit Board Coordinates: 2D-Depth Sensor Applied to Robotic Screwdrivers Assembly Systems
Deformation Behavior and Wear Resistance of Hard TiCN and TiCN/Ti Coatings on Ti6Al4V Alloy
Design of Experiments to Study Slurry Erosive Wear Behavior of Inconel-718 Coatings on Copper
Ga-Doped ZnO Films Deposited by Atmospheric Pressure Plasma
A New Concept of the Sliding Compression Test to Independently Investigate the Contact Normal Stress and the Surface Enlargement
Development of a Self-Propelled Multi-Jet Polishing Tool for Ultra Precision Polishing
Surface Roughness Measurements of a Narrow Borehole — Development of Stylus with Cylindrical Mirror and Lensed Fiber
The Numerical Research of Drag Reduction over Bionic Fluctuation-Adaptive Non-Smooth Surface
Assessment of Using Secondary Concentrators for Nonferrous Material Removal Applications
VII. Computer Aided Engineering
A Study on the Structure Analysis of Skate for Transportation Using Composite Materials
A Study on the Warm Forging-Flaring Process of Brass Tube
Dynamic Simulation and Analysis of Large-Scale Gear Reducers
Flow and Film-Forming Characteristics Analysis of Non-Newtonian Fluid Slot Coating
Investigation of Drilling Conditions of Printed Circuit Board Based on Data Mining Method from Tool Catalog Data-Base
Investigation of Gear Meshing Noise of Planetary Gear Mechanism for Hybrid Vehicles
Prediction of Maximum Forging Load and Billet Volume Using FEM of a Near Net-Shaped Helical-Bevel Gear Forging
Study on Utilizing Rapid Prototyping Technology to Build Oral and Maxillofacial Models
The Development of a Cross-Flow Fan for Electronic Devices Cooling with a Focus on Laptop Computers
The Study on the Boltzmann Distribution of Ideal Gas under Gravitational Field by Computer Simulation
The Effect of Seat Tube Angle (STA) on Muscle Tension Leg Riders
Generalized Two-Point Method for Straightness Profile Measurement - Error Propagation and Experimental Results
VIII. Automation and Manufacturing Systems
Control of Service Robot by Integration of Multiple Intermittent Sensors
Development of an Advanced Semi-Active Damper Using Smart Fluid
Hybrid Genetic Algorithm for Solving Assembly Line Balancing Problem in Footwear Industry
Performance Analysis of an Open-Cathode PEM Fuel Cell Stack
A Survey of Sustainable Design-Centered Integration for Medical Additive Manufacturing
IX. Micro/Nano Technology
Development and Optimization of a Low Normal Force Contact
Mechanism of TiO2 Nanotubes Formation on the Surface of Pure Ti and Ti-6Al-4V Alloy
Nano-Scale Control Design and its’ Practical Implementation of Piezoelectric Materials
The Nanostructure Fabrication on Conductive Diamond-like Carbon Thin Film by Nano-Oxidation Technique
The Study of Aluminum Pattern on Phosphors Anode in Field Emission Device
The Study on the Ultrasound Assisted Atomic Force Microscopy Base Nanomachining
