Sonstiges, Englisch, Band Volumes 690-693, 3870 Seiten, Format (B × H): 125 mm x 142 mm, Gewicht: 200 g
Reihe: Advanced Materials Research
Sonstiges, Englisch, Band Volumes 690-693, 3870 Seiten, Format (B × H): 125 mm x 142 mm, Gewicht: 200 g
Reihe: Advanced Materials Research
ISBN: 978-3-03795-430-0
Verlag: Trans Tech Publications
Autoren/Hrsg.
Fachgebiete
Weitere Infos & Material
Effects of Annealing on Microstructure and Phase Transformation Temperature of NiTiNb Shape Memory Alloy after Equal Channel Angular PressingResearch on Dynamic Recrystallization Behavior of near-a Titanium Alloy during near-? CompressionStructure and Physical Properties of Liquid Ni2Sb98 Eutectic AlloyThe Microstructure Evolution and Twinning Characterization of AZ31 Mg Alloy Sheet in Low-Temperature Bending ProcessAn Experimental Study of High-Velocity Impact on Aluminum Foam Composite Shield StructureExtraction of Tantalum from Ta2O5 Using SOM ProcessReaction Mechanism on Preperation of Ta with SOM ProcessSintering Characters Analysis of the Al2O3-86 Homogenized BauxiteStep Reactive Sintering of Ti2AlNb Based Alloy with Element PowdersStudy on Microstructures and Mechanical Properties of Die Casting Mg-xGd-3Y-0.5Zr AlloysStudy on Sintering Properties of Al2O3-70 Natural Mullite by New ProcessesStudy on the ZK60A and AZ31B Magnesium-Alloy in the Application on High-Speed Train SeatsThe Effect of Heat Treatment on Microstructure and Performance of Die Forging CopperYield of Alloying Elements Fed by Cored Wire into A Copper MeltEffect of Cooling Mode on Properties of a Cast Zinc AlloyEffects of Cr Substitution of Mo on the Formation and Mechanical Properties of FeCoMoCrZr Amorphous AlloysStudy of Thermal Stability of Magnesium AlloysDirect Electrolytic Reduction of Solid Cr2O3 to Cr Using SOM ProcessElectrochemical Behaviors of Die-Cast Mg-4Al-0.4Mn-Xpr (x=0, 1, 4) Alloys in NaCl SolutionAlloy Design and Application for Avoiding Carbide Network of CrWMn Steel by Phase Equilibrium Thermodynamic MethodAtmospheric Corrosion Behavior of Salvaged Marine Cast Iron ArtifactsCharacterization of Passive Film Formed on X80 Pipeline Steel in Sodium Bicarbonate SolutionDevelopment of Hot Rolled Ship Plate with High Strength and High ToughnessEffect of Rare Earth on Microstructure and Mechanical Property of Ferrite Stainless SteelEffect of Slag Composition on Total Oxygen of High Speed Wheel SteelFailure Analysis on Fracture of 16Mn SteelGreen Manufacturing Operation Mode for Iron & Steel EnterpriseImprovement of Radiation-and Thermal Stress-Induced Springback Degradations in Invar Alloy Using Repeated Radiation Plus Hot-Then-Cold TreatmentsIntergranular Corrosion Behavior of 00Cr12 Ferritic Stainless Steels Containing CeriumMicrostructure Evolution and Grain Boundary Characteristics of Oriented Silicon Steel during Primary Recrystallization in a Pulsed Magnetic FieldMicrostructure Refinement of Hypereutectic High Chromium Cast Iron with Electric Current PulseRecrystallization Thermal Simulation Experiment for a Micro-Alloy SteelResearch on a New Secondary Creep Model and Creep Damage Evolution for P92 SteelResearch on Fatigue Behavior of Beam with Corrugated Steel WebsResearch on Molten Steel Flow with Electromagnetic StirringResearch on Powder Metallurgy High Nitrogen Stainless SteelsThe Effect of Finish Rolling Temperature on Microstructure and Mechanical Properties of Vanadium Containing Ferritic Stainless SteelThe Effect of Microstructure on Properties of High Deformation Pipeline Steel X70The Investigation in the Influence of Hardness to Transition Point after Tempering for Boric Carbon SteelsThermodynamic Analysis and Observation of Inclusions in H13 Die Steel with Rare Earth20#,60Si2Mn,9Cr18MoV Steel Ferrite Area Dynamic Recovery and Recrystallization ResearchBeneficiation Study on an Oolitic HematiteCorrosion Property of a New Repair-Free Steel Developed for Bottom Plate of Cargo Oil TanksEffect of Loading Rate on Tensile Properties of Automotive Steel SheetEffect of Secondary Cooling on Non-Oriented Electrical Steel Strips Produced by Twin-Roll Casting ProcessEffect of Tempering Process on Residual Stress in Hot Rolled Low Carbon Martensite High-Strength Steel StripHot Ductility Behavior of 800MPa Ultra High Strength Niobium Containing SteelsNumerical Simulation on Collision and Aggregation Process of Al2O3 Inclusions with Different Morphology CharacteristicsResearch on Using Limestone for Slagging during BOF Steelmaking ProcessStudy on Desulfurization Kinetics Model of LF RefiningStudy on Initial Oxidation Film Formation Mechanism of T23 Steel at 600?CThe Implementation of Steelmaking MES for Pangang GroupThe Investigation on Wire Rod Materials of Low Carbon Steels and Extra Low Carbon SteelsInfluence of Heat Treatment on Microstructure and Properties of Ultrahigh Strength Fe-Ni-Co AlloyCorrosion-Resistant Alloys for Tubings and Casings and Alloy Material Selection in Oil and Gas WellsEffect of Water Vapor on Oxidation of Ferritic Stainless Steel 21Cr-0.6Mo-Nb-Ti in Simulated Reheating EnvironmentStudy of the Effect of W and Mo Binary Alloying on Fe-Ni36 Invar Alloy PropertiesEffect of Pre-Oxidation on the High Temperature Oxidation Behavior of Fe-Cr-Al Powder Porous MetalExperimental Research on Size Effect of Magnetic Hysteresis Loop for Q235 SteelAnalysis and Research on the Microstructure Fractal Characteristics of the Copper Matrix CompositesDynamic Analysis of the Rotating Composite Thin-Walled Cantilever Beams with Shear DeformationFinite Element Model and Bending for Marine Composite Flexible PipesHigh-Temperature Dry Sliding Friction and Wear Characteristics of As-Cast SiCP/A356 CompositeInfluence of Fiber?s Surface State on Mechanical Properties and Fiber-Matrix Interaction of CFRPMicrostructure and Properties of Deformation-Processed Cu?Cr In Situ CompositesPreparation of the High Temperature Resisting Material with Al-CrO3 System by SHSStudy on High-Speed Milling Force of SiCp/Al Matrix CompositeSynthesis and Characterization of MgFe2O4 /MgO Composite Films from Layered Double Hydroxides PrecursorsSynthesis Method and its Influence Factors of Hydrotalcite-Like CompoundsThe Influence of AC Perturbations on EIS Measurement of Copper/LDPE Composite with High ResistanceThe Sorting Method of the same Pattern Compound Material Based on Basic Element Model of Surface MicrostructureVulcanization Kinetics of Starch Xanthate /Natural Rubber CompositeApplication of Diffraction and X-Ray Microanalysis in Study of MMC StructureInfluence of Temperature on Carbonation Pellet for Ferrous DustInnovative Utilization of a Borate Additive in Magnesium Production to Decrease Environmental Impact of Fluorides from Pidgeon ProcessMicrostructure and Formation Mechanism of Two-Liquid Bimetal Composite InterfaceMorphology and Property of Polypropylene Composites Filled with Modified AttapulgiteParameters Optimization of Steel Wire Reinforced Thermoplastics Composite PipePreparation and Characterization of Hydroxyapatite WhiskersPreparation SiC Ceramic Composite Filtration Membrane Materials by Dry Pressing and Synchronous Sintering MethodSilty Clay and Fibre InteractionStudy on Film-Forming Technique of Aluminum Composite Membrane Prepared by Inorganic Precursor Sol-Gel MethodThe Research Progress of Nitinol Vascular StentFabrication and Characterization of NiOx/Bi2WO6 with Enhanced Photocatalytic Activity under Visible Light IlluminationStudy of Microstructure and Properties of Corundum-Calcium Hexaluminate Composite AggregateAdsorption of Congo Red from Aqueous Solution onto Chitosan/Rectorite CompositeA Molecule Computing Model for Maximum Independent Set Problem Based on DNA/AuNP ConjugationPreparation and Photocatalytic Activity of Gadolinium?Doped ZnO Nanocrystalline PowdersPreparation of Nanosized Barium Titanate Powder by a Direct Reactive Precipitation MethodThe Development of Nanocrystalline Materials Prepared by ElectrodepositionThe Effect of PEG on the Preparation of HydroxyapatiteThe Effects of Surfactants on the Topography of HAThe Research of Influence on Fe-N Alloy Magnetism from Experiment ParametersA Novel Hybrid System for the Fabrication of Electrospun Mat with MicrospheresEnhanced Field Emission from Carbon Nanotubes Coated by Nanoparticles of Turbostratic Stacked GraphenesPreparation of Aluminum Nanoparticles and Oxidation Mechanism of Nano- and Micro-ParticlesThe Preparation and Properties of Porous Scaffold Made of Nano-Hydroxyapatite/Polyamide66Studies on Crystallizations and Mechanical Properties of Polypropylene/Nano-TiO2 CompositesThin Film Microcircuit Preparation in a Diamond Anvil CellMicro-Structure of a Special Sericite-Jade: A Preliminary Study Using XRD and SEM AnalysisPreparation of Expanded Graphite with Fe3O4 NanoparticlesStudy on Catalytic Efficiency of Ag/N Co?Doped TiO2 Nanotube Arrays under Visible Light IrradiationA Novel 5-Fluorouracil-Loaded Polyelectrolyte Nanoparticle FormulationAligned Nanofiber Arrays and Twisted Nanofiber Ropes via Electrospinning with Two Frames CollectorEffect of Type and Amount of Wetting Agent on the Formability and Bending Strength of Vitrified Bond Diamond AbrasivesSynthesis of Al2O3 Ceramics Matrix Composites by Thermal Explosion under Pressure and Hot PressingFabrication of ZrB2-Based Ceramics Doped with ZrSi2Study of Domains and Size Effect of Curie Temperature in BaTiO3 NanoceramicsStudy on Grindability Evaluation of Ceramic Materials Based on Interval Gray Principal Component AnalysisThe Progress of Amorphous Si-B-C-N Composite CeramicsEmission Color Variation of Sr3SiO5:Ce3+, Li+ Phosphor for Near-UV Light-Emitting Diodes by Co-Doping with Mg2+ and Ba2+First-Principles Investigations of Structural Stability of LuNInaln/GaN HEMT Small-Signal Parameter ExtractionInfluence of Deposition Temperature of ZnTe Films on Silicon by Thermal EvaporationPreparation and Characterization of a Novel Gadolinium Triple-Decker Sandwich-Type Complex with Tetrabenzoporphyrin LigandAn Integrated Evaluation Model for New Product Development in Light-Emitting Diode Plant Lighting IndustryCasted Strip Character of Twin-Roll Casted High Strength Non-Oriented Electrical SteelDFT Studies on the Electronic Spectrum and the Second-Order Nonlinear Optical Properties of Donor-Acceptor HelicenesFerromagnetic Material of the Nearly Half-Metallic Alloy Co2TiGaLuminescence Properties of ZnO:Eu3+ Red Emitting Phosphor Prepared by Precipitation MethodMagnetic Material Based on Full-Heusler Alloy Co2CrGaStructural Stability, Electronic and Optical Properties of Ni-Doped Boron Carbide by First Principles CalculationStudy the I-V and C-V Characterization of n-ZnO/p-Si HeterojunctionStudy of Optical Characteristics of H2S Molecule Adsorption on Agn (n=3,5) ClustersPreparation of Stilbene-Eighteen Alkyl Quaternary Ammonium Salts as Fluorescent Brightening Materials and SurfactantsSynthesis and Properties of Novel Hole-Transporting Materials Containing Triphenylamine and Bipyridine UnitsElectronic Properties of Zno Doped by Rare-Earth Elements from First-PrinciplesThe Influence of B2O3 on the Luminescence Behavior of ZnGa2O4 Phosphor at Different Sinter TemperaturesCarbon Cloth Diffusion Layer for Fuel Cell ElectrodeThe Influences of Zirconia on the Properties of Magnesia Alumina Spinel BricksTi2AlC/TiC Functionally Graded Material Fabricated by Reaction SinteringThe Microstructure and Thermochromic Properties of La1-XSrXMnO3 Smart MaterialsInvestigation on the Creep property of Theoretical Composition Magnesia Alumina Spinel BricksInfluence of Fe2O3 on the Hydration Resistance of MgO-Al-C BricksEffects of Sodium Salt on Hot Mechanical Properties and Microstructure of MgO-Al-C BricksUse of Waste Tire Rubber Particles as a Part of an Aggregate Added to Thermal Insulting MortarBuilding Energy-Saving Technology and its Application Based on Low Carbon ConceptBuilt-In Spiral Ripe Thin-Walled Square Steel Tube Concrete Column of Nonlinear Finite Element AnalysisEffects of Clay on Flow Properties of Polycarboxylate Superplasticizer and its Control MeasureEffects of Ferrocement in Strengthening the Serviceability Properties of Reinforced Concrete StructuresElementary Discussion on the Treatment of Old Road Problems in Upgrading and Reconstructing for the RoadFinite Element Analysis for Concrete Filled Double-Skin Steel Tubular Stub ColumnsPreparative Techniques and its Performance of Chemically Foamed Cement PasteResearch on Building Low-Carbon Hotels from the Perspective of Circular EconomyResearch on Mass Concrete Construction Techonogy of Raft Foundation of Hongyun BuildingShort- and Long-Term Deflection of Concrete StructuresStability Bearing Capacity of Concrete Filled Thin-Walled Circular Steel Tubular Column under Axial CompressionStudy on Clinker Production Using Magnesium Slag on a 4500tpd LineStudy on Crack Spacing and Width of Expansive Soil due to EvaporationStudy on Medium Density Radial Bamboo Curtain Composite PlybambooStudy on Particle Characteristics of Cement by Vertical Roller Mill Finish GrindingStudy on the Axial Ultimate Bearing Capacity of Concrete-Filled Square Steel Tubular Stub ColumnsTest of Dynamic Strength Characteristics of PaleosolTest Research on Stiffness of Loaded Concrete Beams Strengthened with Prestressed CFRP SheetsThe Affecting Factors of Slope Stability Based on Orthogonal DesignThe Effects of Steel Content for the Mechanics Performance of Fiber Modified Polymer Resin ConcreteThe Guidance Pattern of Countryside Sustainable Development of Three Gorges Reservoir in ChongqingThe Influence on the Concrete Durability in Bleed Air Performance Caused by Concrete AdmixtureThe Inhibition Studying of Many-Doped Mineral Admixture for Concrete Alkali Silicate ReactionThe Inhibition Studying of Single-Doped Mineral Admixture for Concrete Alkali Silicate ReactionThe Inspiration from the Slow-Traffic and Lingering Characteristics of the Inhabited BridgeThe Studying of Reinforcement Mechanism of Fully Grouting Rock Bolt in Brittle Wall Rock MassTowards a Competitive City: Shanghai's Urban DevelopmentUnified Solution of the Ultimate Bearing Capacity for Stiffened and Thin-Walled Square CFST Short Columns under Axial CompressionA Review of Detection, Evaluation and Repair Technology for Hydraulic Concrete StructuresActive Countermeasure Mechanism to Waste Dump Based on Spatial EffectAnalysis on Characteristics of Ancient Kiln Village in MengjiajingAnalysis On Morphology Of Settlement and Residence In Wangyu VillageAnalysis on Seismic Behavior of Structures Supported by Foundations with Different LocationsConcrete Slab Value Stream Mapping of Brazilian Residential Buildings - a Lean Construction Study CaseEffect of Pore Structure on the Chloride Permeability of Concrete with Mineral AdmixtureEnergy Conservation Technology in BedZED and the Enlightenment for ChinaEvolution and Significance of the Residential Area of Landscape DesignFrom the National Historical and Cultural City of Shanxi DaiXian see Ancient Frontier Town History Culture and the Characteristics of the Development of CityFrom the View of Qujia Courtyard House of Shan Xi Dwellings Traditional Cultural ValueMethod and Trend of Residential Landscape DesignPaying Attention to the Application of Ecological Strategy to Construction DesignProduction of Concrete Blocks with Residues for Civil ConstructionProtection and Sustainable Development of Jiexiu Ancient CityResearch and Application of Corundum Based Self-Flowing Castable RefractoriesResearch on Axial Behavior of Thin-Walled T-Shaped Steel Stub Columns Filled with Recycled Demolished Concrete LumpResearch on Spacial Displacement Regulations in Soft Surrounding Rock TunnelSoil Erosion Assessment in the Watershed of Dehua District of Fujian ProvinceStudies on RC Beams Strength with Steel Wires Using Nolinear Finite Element MethodStudy on Influencing Factors of CFST Arch Bridge StabilityStudy on Recognized Mode of the Revolutionary Site Protected Object in Traditional VillageThe Cause of Cracks in the Cement Concrete Pavement of County-Highway and Precautionary MeasuresThe Finite Element Analysis of Thin-Wall Ribbed Square Steel Tube Recycled Concrete Bias Column Mechanical PropertiesThermal Conductivity of Fired Clay Bricks Incorporated with Cigarette ButtsStudy on the Natural Vibration Characteristics of Jointed SlopeThe Evaluation System of Urban Low-Carbon LevelAnalysis of the Effect of Natural Slope Stability due to Tunnel Excavation in Mountainous AreasEffect of Argon Gas Flow on the Thermal Field in a Directional Solidification System for Multi-Crystalline SiliconEffect of Sodium-Based Slag Treatment on the Distribution of Impurities in Metallurgical Grade SiliconMaximized On-Demand Hydrogen Generator DesignPurification of Silicon by Solvent Refining with Si-Sn AlloyStudies on the Electrochemical Behavior of Sio/C Anode Materials by AC Impedance MethodSummarize the Studies on Improving the Electrochemical Performance of Spinel LiMn2O4Temperature Distribution of Multi-Crystalline Silicon Ingots in the Directional Solidification ProcessCathode Material Li [Li0.2 Mn0.44Ni0.18Co0.18]O2 Synthesized by Molten Salt MethodFabrication of Micro DMFC Stack Using MEMS TechnologyMathematical Modeling of a DMFC Cathode with a Double Catalyst Layered Structure Membrane Electrode AssembliesA Technological Method to Improve the Filtration Efficiency of Fiber MaterialsEffects of Laccase on the Properties of Hemp FabricExperimental Study on Cr6+ Adsorption in Water about the Daily Waste Peanut ShellPreparation and Mechanical Properties of the Environmentally Friendly Wood-Plastic CompositesPreparation of Calcium Sulfate Anhydrate Whisker and a Primary Investigation of its Arsenic Removal PerformanceRemoval of Natural Organic Matter of Artificial Lake by Modified Fly AshStudy on the Environmental Friendliness of Biomass Dishware Based on Life Cycle AssessmentSurface Morphology and the Adsorptive Behavior of Coconut Active CarbonAdsorption Characteristic of Steel Slag Haydite for Phosphorus Removal from WastewaterAdsorption of Cr(VI) from Aqueous Solution by two Kinds of Pillared BentonitesColumn Experiment on Cr (VI) Reduction with SiO2-Coated Fe NanocompositesEarly Strength Characteristics of Palm Oil Fuel Ash and Metakaolin Blended Geopolymer MortarInfluence of Organic Alkali on the Preparation of Lignin-Based Anionic Adsorbents and their Performance in the Removal of NitrateStrength and Durability Characteristics of Polymer Modified Concrete Incorporating Vinyl Acetate EffluentStudy on Production Technology of Paper Wooden Compound PalletsSynthesis of Epoxidized Soybean Oil via Phase Transfer CatalysisTertiary Treatment of Paper Industries Effluent with Advanced Electrochemical Oxidation Process in the Presence of Modified Bentonite Powdery ElectrodesAnalysis on Distribution Law of Damaged Filters for Bag Dedusters in Coal-Fired Power PlantsFactors Influencing the Removal of As(V) from Groundwater by NF/ROEffect of Preparation Method on Photocatalytic Activity of Titanium-Bearing Blast Furnace SlagThe Influence Factors of Compressive Strength and Production of Mineral Polymer of Aluminum Rocks in Xiuwen County, Guizhou Province, ChinaCharacterization of some Key Industrial Waste Products for Sustainable Concrete ProductionA Study on Wellsite Wastewater Reinjection Stratigraphic Control in Changqing OilfieldEffects of Latency Removal on the Fiber Properties of Poplar APMPGreen and Efficient Coal Slurry Drying ProcessStudy on Factors and Operation of Granulation Method for Strontium RemovalThe Influence of Ph Value on the Treatment of Direct Sun-Proof Dyes Wastewater by Iron TrichloridePreliminary Study of Utilizing Ozone in Treatment of Operationally Exhausted Metalworking FluidsPurification Effect of Self-Aeration Constructed Wetlands on CODResearch on Removing Radioactivity Minerals Form Titanium Rough Concentration of HaibingSelection of Substrate Diameter and Filling Thickness for Artificial WetlandStudy on Cyclone Dust Removal Equipment after Dense Phase Semi-Dry Flue Gas Desulfurization SystemEffect of Wet Storage on High Yield Pulping with H2O2-CoSO4Dynamic Response of the Compound Structure of Foam Aluminum Core Composite Sandwich Material to the Shock Wave of Gas ExplosionSeismic Hazard Estimation in East China Offshore AreasAeolic and Seismic Structural Vibrations Mitigation on Long-Span Cable-Supported BridgesOn the Generation of Seaquake Velocity Fields for Submerged Floating Tunnel StructuresActivation Energy of Pure and Impregnated Lignocellulosic Materials Obtained by Isothermal MethodAdsorption of Acid Red by Porous Chitosan FilmAsymmetric Synthesis of Ethyl (R)-4-Chloro-3-Hydroxybutanoate with a Two Recombinant Escherichia coli SystemComparison of the Roles of Tea Polysaccharides and Polyphenols in Growth Inhibition of Hepatoma H22 Cells in MiceEffects of the Protein in Wheat Straw on Enzymatic HydrolysisEnzymolysis Optimization of Walnut Residue Protein Using TrypsaseImmunomodulatory Activity in Vivo of Porcine Cartilage Polysaccharide Nanoparticles on Murine H22 Hepatocarcinoma CellsInfluence of Cortical Layer Thickness of Alveolar Bone on Stress Distribution over Implant Supported RegionKinetics Study of Vitamin A Precursor Synthesis by Immobilized Lipase-Catalyzed Regioselective Monoacetylation in n-HexaneMechanism of Peptide Changes during Drying Fermented Soybean MealNumerical Simulation of Cell Growth Pattern and Determination of Fractal Dimension of Cell ClusterOptimization of Multi-Strain Solid State Fermentation to Improve the Content of Soybean Meal Protein by Response Surface AnalysisOptimization of Solid State Fermentation to Improve the Degree of Hydrolysis Soybean Meal ProteinPreparation and Characteristics of Chitin-Gelatin Composite Film
Prokaryotic Expression and Purification of Tomato Cnr ProteinProtein Extraction of the Long-Term Room Temperature Storage Wheat StrawResearch on Oxidation of Phenanthrene to Phenanthrenequinone with TBHPSelectivity of the Cycloaddition of Tert-amyl Alcohol and a-methylstyreneStudies on Charcoal Block Production from Three Charcoal Types of Biomass Employing Screw Press UnitStudy of Physicochemical Properties of Chinese Small Cabbage(Brassica chinensis L.) Stored at Four TemperaturesStudy on Hydrophobic Microorganism as Coal Bio-Desulfurizing AgentStudy on the Isolation of Polysaccharide from Purple Sweet Potato by DEAE-Cellulose 52Synthesis and the Study of Oil Displacement Performance of Stearate-2-Hydroxy-3-Propane Sulfonic Acid Sodium SaltThe Assessment of Sweet Sorghum Straw Bio-Feed Fermentated by the Compound Microbial Agent in Bags and Cellar PitsThe Classification and Characteristic of Proteins in WheatThe Effects of Rhodiola Tibetica on Lung Tissue of Rats with High Altitude Pulmonary EdemaThe Wool Shrink-Proof Technology of Sericin Bonding WoolConstruction of Expression Vector with Fruit-Specific Promoter and Genetic Transformation of StrawberryDetermination and Identification of Chondroitin Sulfate from Tilapia ByproductsEffect of Xylanase Treatment on Papermaking Properties of Poplar High Yield PulpEmulsifying and Foaming Properties of Wheat Gluten Influenced by High Pressure MicrofluidizationFlame Retardation of WoodHigh-Purity Isolation of Trans-Resveratrol from Rhizma Polygoni Cuspidati by High-Speed Counter-Current ChromatographyInvestigation of Airflow Influence on Self-Heating Process of Linseed Oil Using Safety Calorimeter SEDEXIsolation of Saccharomyces Cerevisiae GJ03 from the Spontanous Fermentation Orange Wine and Application in the Course of Orange Wine BrewingMechanisms and Defiberation Point of Dendrocalamus Giganteus Munro Kraft PulpingOptimization of The-Hydrolysis Parameters of Dissolving Pulp of Fast-Growing Poplar ProducingPreparing Gambiered Guangdong Silk with Ultraviolet Radiation and Normal Mud/Fe2+Purification and Preliminary Characterization of a Thermostable Lactase from Bacillus coagulans T242Research on the Antioxidation of Torreya Grandis Alcohol Extracts in Cholesterol-Fed RatsSimulating Glycolytic Metabolism of Escherichia coli by Using Optimal Control ModelsStudies on the Preliminary Characterization of a Novel Exopolysaccharide Produced by Streptococcus thermophilus Strain from Tibetan Kefir GrainStudy on Deproteinization of Polysaccharide from Corn Silk with Cetyl Trimethyl Ammonium BromideStudy on Furfural Production from HemicellulosesStudy on Plant Growth Regulation Activity of the Low Polar Fractions from Mikania micrantha H.B.K. on Phaseolus radiausStudy on the Emulsifying Properties of Tilapia Skin GelatinStudy on Extraction of Wasabi Plant Material Bio-Activity Substances and Anti-Cancer ActivitiesStudy on Extraction Technology of Polysaccharide from Pleurotus ostreatusThe Ameliorative Effect of CPCC and Role of CRT in Hepatic Injury by Alloxan-TreatmentThe Influence on the Milk Yield and Milk Composition of the Cows after Feeding with the Sweet Sorghum Straw Fermented by the Compound Microbial Agent in BagsThe Spectrum Properties of Type ? Collagen Self-Assembly FilmTheoretical Investigation on Tautomerization Mechanism of 6-ThioguanineUgonin K Induces Cell Cycle Arrest and Apoptosis through Reactive Oxygen Species/Apoptosis Signal Pathway in Human Skin Cancer CellsClean Method for Stickies Control with StickAway Enzyme in ONP PulpsInfluence of Surface Zeta Potential on Adhesion of Chlorella sp. to Substratum SurfacesStudy on Amphiphilic Macromolecules Adsorbent of Cellulose Mixes Ether Based on Cotton StalkProduction and Utilisation of Non-Conventional CokeHigh-Consistency Electrochemical Delignification of Poplar Kraft PulpGold Immunochromatography Assay - A Newly Rapid Detection Technique for Aquatic ProductsUsing of Magnesium Hydroxide and Sodium Hydroxide in DP Beaching of NaOH-AQ Wheat Straw PulpPreparation and Characterization of Regenerated Wool Protein PAN Blended FibersBiocompatibility Research of the Biphasic Calcium Phosphate Composite Ceramic Film Obtained through Micro-Arc Oxidation on the Medical Titanium SurfacesDetermination of Ignition Temperature of Organic Dust LayersPreparation and Characterization of Alkylethoxyethanesulfonate in Superbasic System KOH-DMSOPreparation and Properties of Modified Lignin Used as Additive of Brown Coal CWSPreparation of Aromatic Silanes as High Thermal Stability Coupling AgentsRemoval Efficiency and Distribution Characteristics of PAHs in Coking Plant Contaminated Soils by In Situ Chemical Oxidation RemediationCascaded Columns of Total Reflux Batch Distillation with Periodic Liquid ExchangeEffects of Microwave Power on Performance of Pt/CeO2MWCNTs Catalysts Prepared by Microwave-Assisted Polyol Process for Methanol ElectrooxidationExperimental Study of Optimal Coagulation Effect on Three Kinds of Direct Sun-Proof Dyes by FeCl3The Evaluation of Factors Affecting the Performance of Heavy Oil EmulsionKinetic of C.I. Reactive Black 5 by Fenton-Like OxidationResearch on Tubing and Casing Corrosion in Sour Gas Reservoirs and Corrosion-Resistant Material SelectionMaterial Selection of Water-Ring Vacuum Pump in Yellow Phosphorus Tail Gas IndustryPreparation of Strontium-Barium Hydroxyapatite by CoprecipitationModified Cuo/ZnO/Al2O3 Catalysts for Methanol Synthesis from Co and CO2 Co-HydrogenationStudy on the Reaction Kinetics and Catalytic Stability of Pillared Bentonite in Heterogeneous UV-Fenton ProcessDistribution and Bioavailability of Nitrogen Species in Street Dust from Small Towns in Yongchuan, ChongqingThe Characteristics of Trace Metal Elements Accumulation and Distribution in Elsholtzia HarchowensisDyeing of Cotton Fabric Modified by 2, 3-Epoxpropyl Triethyl Ammonium Chloride with Reactive DyesAdhesion Loss in Antistripping Agent Treated Asphalt Binders due to MoistureExperimental Research on the Solubility of Cellulose in Different Ionic LiquidsInfluence Analysis of the Parameters on Sound Absorbing Performance for Polymer WoolPreparation and Properties of Silane-Terminated Poly(urethane-Imide)Preparation of High Heat-Resistant Profile Based on PVC/a-MSAN/ABS Ternary BlendsStudy on Properties of Enzymatic Hydrolysis Lignin (EHL) and Chloride Polyethylene (CPE) CompositesStudy on Relationship between BPA Migration and Thermal-Oxidative Aging Degree of PolycarbonateSynthesis of a New Water-Soluble Conjugated Polymers Containing Thiazoline Moiety for Antibacterial Activity BioassaySynthesis of Quaternary Ammonium Cationic Polymer PEASynthesis of UV-Writing Fluorinated Polymer for Organic Optical WaveguideThe Studies on Crystallization of Polypropylene (PP)/Nano-TiO2 Composites under Microwave IrradiationThe Swelling Kinetics Study of Hydrogels Prepared by the Different Finesses Degrees of Eupatorium AdenophorumEmulsifier-Free Core-Shell Hybrid Latexes from Castor Oil-Based Waterborne Polyurethane and Polyacrylate Containing Fluorine and SiliconResearch on the Relationship between the Productivity of Antarctic Krill Chitin and its Fineness of GrindSynthesis and Properties of a Castor Oil-Based UV-Oligomer Comprising of Side-Chain BenzophenoneThe Best Dosage of Polymer Dispersant in WDG by Zata Potential MethodThe Surface Modification and Characteristics of Useful Expanded PTFE Composites by Photo-Radiation MethodsStudy on Pretreatment Agent for Anti-Clogging in Polymer Flooding WellsSynthesis of Poly(acrylic Acid Dodecyl Ester-Styrene-Maleic Anhydride) Terpolymer and Surface Modification of Glass FiberStudy on the Preparation of 2-Phenyl Imidazole Microcapsule and its Effect on Curing Epoxy ResinAluminum-Induced Crystalization of Amorphous Silicon Films Deposited by Megnetron SputteringElectrodeposition and Properties of CuInS2 Thin FilmsOn the Mechanism of Copper Oxide Reduction by Dielectric Barrier Discharge Plasma Using H2 and Ar Mixture GasesPreparation and Properties of Cu2ZnSnS4 Nanoparticles by Solvothermal MethodProperties of Ohmic Contact of Au Electrode on Polycrystalline Mercuric IodideCharacterization of TiO2 Composite Film on Steel Obtained in Aluminate Electrolyte by PEO and the Photocatalytic ActivitiesEffects of Preparing Conditions on NO2-Sensing Properties of Sputtered WO3 Nano-FilmsElectrochromic Property of Sputtered Amorphous NiO FilmsHydrogen Induced Modifications of Optical and Electric Properties in Mg Thin FilmsStructure Characterization of W-Doped Vanadium Oxide Thin Films Prepared by Reactive Magnetron SputteringStudy on Wurtzite-ScxAI1-XN Thin Film: A ReviewThe Structure and Magnetic Properties of NiZn-Ferrite Films Deposited by Magnetron Sputtering at Room TemperatureZnSe Quantum Dot Films Deposition from Modified Chemical Solution with Sodium CitrateBending Ratcheting Behavior of Zircaloy-4 Alloy at Room TemperatureExperimental Study on Fatigue Behavior of 35CrMo Steel after Torsional PrestrainFirst-Principles Study of the Elastic Properties of Hexagonal Phase ScAx (A=H, He)Improved Extend Finite Element Method for SIF CalculationMechanical Behavior Research of a Novel Bridge Tower Structure Based on Model TestNumerical Simulation of the Effect of Temperature on the Failure Strength of RockReliability Study on Crack Growth Rate of ADB610 SteelStatistical Analysis of Fatigue Crack Growth Rate of Q345E SteelSuper Long Life Fatigue Properties of Rail Steel U71Mn and U75VAnalysis on Creep Behaviors at High Temperature and Fracture Morphology of P92 SteelsComparison of the Simulation and Experimental Fatigue Endurance Behaviors in T6-Treated Nanosized SiC Reinforced Al Alloy CompositeExperimental Study on Out-Plane Crack Extension in Rimmed SteelFracture Analysis on Drainage Pipe Socket of BoilerHigh Cycle Fatigue Behavior of Eco7075-T73 Aluminum AlloyPrediction of Fatigue Crack Growth of 2024-T351 by Grey GM(1,1) Model with Rolling CheckResearch on the Effect of Pre-Stress on Bending Stiffness of the Ball Screw Based on ANSYSStudy on Kinetic Competitions of Crystal GrowthTensile Characteristics of Polygonaceae Weed Roots in Slope Collapse WatershedThe Fracture Failure Analysis of Shaft for Light Hydrocarbon PumpApplications of a New Element Model of Solid Bodies in PlasticityAnalysis of Fatigue Life and Influence Factors of Tubing with Initial CrackCheck on Structural Strength of Carbon Fiber Composite Field Kitchen UnitsInvestigation and Analysis on Transverse Crack Spacing Distribution in Continuously Reinforced Concrete Pavement in ChinaNumerical Solution of Constant-Q Fractional Order Integral ModelingResearch of Baseball?s Best Batting Position Changes with the Selection of Material of BaseballDevelopment of Hard Rock Cutting Tool with Advanced Diamond CompositesResearch on Properties of Materials Based on Extension Evaluation MethodInfluence of Rear Earth Yb on the Specific Heat of Liquid Fe-Co-Yb AlloyLateral Non-Uniformity Charges Influence on Interface Trap Density (Dit) by Terman Method in the nMOS FabricationAblation/Erosion Test Technology on C/C Composite Material Based on PlasmaEvaluation of CO2 Absorbent/De-Absorbent by AAO/CaO MembraneApplication and Evaluation of New Cold Insulation Material in Cold Insulation Structure of Oil and Gas Processing DeviceOn-Road Gaseous Emission Characteristics of China IV CNG Bus in ShanghaiA New Experimental Technique for Dynamic Material PropertiesOn the Experimental Investigation of Rock Abrasiveness in Petroleum EngineeringAnalysis on Sealing and Deformation of Exhaust Valve Housing of Marine Diesel EngineAnalyzing Bearing Capacity Influence due to Location of Bearing Push-Extend Reamed of the Push-Extend Multi-under-Reamed PileCharacteristics of Thin Metal Plate Being Strengthened by Laser IrradiationDesign of Variable Airship Mechanism Based on Finite Element MethodFinite Element Analysis of the Strength of Ladder Type Structure of the Deep-Water AUVThe Coupled Thermal and Mechanical Load Analysis in the 6S50MC-C Type Marine Diesel' PistonThe Finite Element Analysis of Ultimate Bearing Capacity of Initial Bending on the T-Axis Compression ComponentTheoretical and Numerical Solution of Deflection of the Circular Ring under a Concentrated ForceEffect of Track Measuring Beam on the Bogie Frame Strength and Vibration Mode of Inspection CarEnhancement Design on Composite Blade Structure of Small Wind Turbines Using Finite Element AnalysisFEM Based Statics Analysis of the Main Steel Structure of Bucket Wheel Stacker-ReclaimerFinite Element Analysis for the Collapse Accident of One 110kV Transmission TowerMechanical Strength Analysis and Structure Improvement of Diaphragm Chamber Based on Finite Element MethodNumerical Simulation on Structural Strength of Cam Mechanism for Automobile Panel DieResearch on Screw Pump Rotor Eccentricitys Influence on Sucker Rod Partial Abrasion through Contact AnalysisThe Application of AAR Load Spectrums in the Fatige Assessment for G70 Tank CarbodyThe Mechanical Property Comparison of Two Kinds of Counterweight Booms of Stacker ReclaimerAcoustic Emission Signals Characteristics of Q345R at Tensile Progress in the Normal and Low TemperaturesExperimental Study of Dynamic Characteristics of Dry Friction Damping of Turbine Blade SteelFever Analysis and Engineering Applications of the Heavy Machine Tool's Main BearingKey Aspects in Addressing Friction in Coaxial Hydraulic Sealing SystemsProgress on Facilities and Methodology to Evaluate Abradable Seal CoatingsStudy on Tribological Performances for Textured Bearing of ICEThe Analysis of the Influencing Factors about Friction and Wear Characteristics of the Piston Ring in Stirling EngineThe Effect of Friction Coefficient on Fretting Fatigue CracksStudy Film Temperature Including Cavitation Effect of Sliding Bearing by CFD MethodResearch on the Reinforcement Mechanism of Stretched Rock Bolt and Analyzing of the Impact ParametersApplication of CBN Cutting Tools in Hard Turning and Tool WearExperimental Investigation on Ultrasonic Vibration Assisted Turning of Stainless Steels with PCD ToolStudy of the Effect of Tool Wear on Cutting Ti6Al4V ProcessArc-Spraying Composite Coatings on Mild Steel for Long-Term High-Temperature Oxidation ProtectionCracking Behavior of Two Kinds of Plasma Cladding Layers by Precursor Carbonization-Composition ProcessEffect of Pt Content on TGO Growth in EB-PVD TBC Systems with Niptal BondcoatsEvaluation Hard Layers in Steel AISI 8620Formation of Hard Layers in Tool SteelsIn-Flight Particle Behavior Measured by DPV-2000 System under Low Pressure ConditionProcess Characteristics and Experiment on Micro Arc Oxidation of Light MetalsStudy on Water-Based Paint Stripper for TinplateSurface Activity Research of Cationic Gemini SurfactantsSynthesis and Properties of Hydroxyapatite-Containing Porous Titania Coating on Titanium by Ultrasonic Shot Peening and Micro-Arc OxidationThe Irradiation Effects of Metal Gold Surface by Intense Pulsed Ion BeamThe Study of Aromatization Performance of HZSM-5 Catalyst Deposited Silicon on the SurfaceAnalysis of Selective Absorber Coatings on Thermal Performance of the Solar Flat-Plate CollectorCharacteristics Evaluation of Coating Film by Thermal Spray in Seawater SolutionComparison Research on Mechanical Properties of Stainless Steel after Laser Peened and Ultrasonically PeenedEffect of Electro-Spark Deposition Process Parameter on WC Coating Thickness of H13 Steel SurfaceEffects of Carrier Gases on the Microstructures and Properties of Ti Coating Layers Manufactured through the Cold SprayingInfluences of Surface Nanocrystallization Induced by High-Energy Spot Peening on Microstructure and Properties of Magnesium AlloyInvestigations of Wetting Properties of Stainless Steel by Molten Multi-Component OxidesPolymer Mixtures as Colon Targeted Drug Delivery SystemsStructrure of Al2O3 Ceramic Coating on Super Alloy Prepared by Cathodic Plasma Electrolytic OxidationStudy on the Surface Plasma Hardening Treatment and Anti-Penetration Mechanism of Armor SteelThe Study on Preparation and Apply of Ni-Co-P Alloy CoatingElectroless Nickel-Phosphorus Plating on TiB2 PowderPhase Evolution and Mechanical Properties of Cr-C Coatings Deposited by Reactive Unbalanced Magnetron Sputtering ProcessFirst-Principles Study on Elastic Properties and Electronic Structure of Ti1-xAlxNPreparation and Cutting Performance of YT15 Cemented Carbide Tools with Ti (C, N)/Al2O3 Composite CoatingEffect of Abrasives on the Lapping Performance of 6H-SiC Single Crystal WaferFabrication and Characterization of Magnetic Polymer ICF Target by the Electroless PlatingA Study of the Microstructure and Mechanical Properties of C-Si-Mn Hot Rolled Dual Phase SteelAnalysis and Research on the Failure Mode of Large Automobile Stamping and CountermeasureAnalysis on Structure of Radial-Axial Ring Rolling Experimental Equipment by FEMContinuous Cooling Transformation Behavior of X70 Pipeline SteelDesign and Analysis of the Low-Speed Hydraulic Control System of 3.15MN Forging PressDesign of a New Type Flexible Stretch-Forming MachineEffect of Lubrications on Quick Plastic Forming Behavior of AZ31 Magnesium Alloy SheetEffects of Strip Thickness Difference on Deviation in Aluminum Hot RollingEffects of Surface Roughness Microtopography on Formability in Cold Rolled Steel SheetForecast of Shrinkage Porosity of Aluminum Wheel Liquid Die Forging in Solidification Process and Process OptimizationHot Stamping and Blank Designing for a Vehicle Bumper Using Ultra High Strength Steel (UHSS)Investigation on over-Spray Powder of Spray Formed Al-22Si-5Fe-4Mn-3Cu-1Mg AlloyStudy on Design Parameters of Strip Wound Prestressed Die Based on Fatigue TheoryStudy on Texture of AZ80 Magnesium Alloy Induced by Multi-Axial ForgingStudy on the Flow Stress of the High-Mn Austenitic Steel during Hot DeformationStudy on the Parameters of Piercing Die with Finite Element MethodThe Effect of Pre-Strain and Strain Aging on Properties of X100 Line PipeA Review of Liquid Forging ProcessDevelopment of Intelligent Control of Optimum Parameters in Deep Drawing of Sheet Metal Using Genetic Algorithm and Finite Element MethodsDevelopment of Secondary Controlled Hydraulic Pressure Forming of Sheet Metal for Energy Saving and Re-Utilization:Effect of Initial Position of the Counterpunch on T-Shape HydroformingEffects of Mandrel Structure on Ring Rolling Process for Large-Scale T-Sectioned Ring with Numerical SimulationEffects of Process Parameters on Wall Thinning Ratio during One Pass Hot Power Backward Spinning for 7075 Cast Aluminium Alloy TubeFEM-Based Analysis on the Process of Tube StampingFinite Element Analysis for 40 MN Die Forging PressFinite Element Analysis of Main Stand of ?140 Pipe Rolling Mill and Split CastingFlow Stress Models Analysis for Metal Powder Forming SimulationInvestigation of Effective Parameters of Spring-Back in CK67 Steel Sheet Metal Using Finite Element MethodParameter Optimization of the Injection Molding Process for a LED Lighting Lens Using Soft ComputingPlastic Instability Criterion of Radial Ring RollingPulse Current Auxiliary Tensile and Bulging of Light Metal AlloyRolling Force Prediction System of Cold Rolling Process Based on BP Neural NetworkUse of Acoustic Energy in Sand Casting of Aluminium AlloysStudy on Conventional Domed Bursting Disc Material and Burst Pressure TestNumerical Simulation of Stress-Strain of AZ31 Mg Alloy Profile during Warm Tension-Rotation Bending ProcessSmall Module Involute Spline Processing with Position RequirementsResearch on Key Processing Technology of Nuclear Power Tapered Cylinder ForgingA Theoretical Model of Grinding Force and its SimulationAn Experimental Study of Cutting Forces in Ball-End Milling of AISI H13Analysis on Milling Stability Performed under the Conditions of Positive and Negative Process StiffnessChip Formation Simulation in FE Modeling for Machining FRP CompositeCutting Force Modeling and Prediction in End Milling Including Flank WearEffect of Microstructure on Cutting Force and Chip Formation during Machining of Ti-6Al-4V AlloyExperiment on Surface Roughness and Acoustic Emission Signal in Infeed Period of Cylindrical Plunge GrindingExperimental Study on Hardness of Titanium Alloy Ti-1023 by MillingGrinding Parameters Optimization of Stainless Steel Surface Based on Grey Relational AnalysisMachining Simulation of Equal Base Circle Bevel Gear Using Disc CutterMath Modules Establish for BUR Edge Chamfer and its Grinding ProcessModeling and Analysis of Machining Force in Elliptical Vibration CuttingModeling of Force on Axial Power Ultrasonic HoningResearch of Bearing Crown Roller-Raceway by Non-Uniform Interelectrode Gap Electrochemical Mechanical MachiningResearch on the Relation between Cutting Parameters and Axial Cutting Force in Helical Milling ProcessResearch on the Rock Breaking by Double Disc Cutter Test-BedSimulation on Material Removal during Reciprocating Traveling WEDM of Insulating CeramicsStatic and Modal Characteristic Analysis of a Horizontal Machining CenterStudy on Machinability of Pre-Hardened Plastic Mould SteelThe Analysis of Static and Dynamic Characteristic in Grinding Head of Roller MachineThe Influence of Variable-Speed Waveforms on Vibration Suppression in Time-Varying Speed CuttingDrilling Simulation of Carbon Fiber Reinforced Plastic Composites Based on Finite Element MethodExperimental Investigation of Effect of Gear Milling Parameters of Al-B4C Composite Gears on Surface RoughnessInvestigation on Delamination Factor in Drilling Medium Density Fiberboards with Variable Feed Pressure Using Multi-Spindle DrillParameter Recognition and Optimization of Residual Stress Prediction Model Based on Genetic AlgorithmPrediction of Surface Roughness on CNC Turning Based on Monitoring of Cutting Force and Cutting TemperatureStudy on the Ultrasonic Characteristics in the Contact Interface under Ultrasonic CuttingThe Effect of Tool Geometrical Parameters on Cutting Temperature Based on Deform-3DThe Nano-Cutting Mechanism Research of Polysilicon Based on Molecular DynamicsAn Investigation on Vacuum Brazing of Dissimilar Nonferrous Metals of Cu and AlEffect of Magnetic Field Current on Microstructure and Properties of AZ91 Magnesium Alloy Welded JointEffects of Welding Heat Input on 22MnB5 Steel with Hot-Dipping Al CoatingInfluence of Reflow Soldering Process Parameters on the Lead-Free Reflow ProfileLife-Cycle Energy Analysis as a Method for Welding Joint DesignModeling and Simulation on Temperature Control System for Hot Pressure WeldingWeld Seam Deviation Detection Base on Laser Welding Pool?s CentroidAnalysis of Organizations of Brazed Seam 5052 Al Alloy Contact Reactive BrazingBayesian Probabilistic Approach to FE Model Updating of Vehicle Typical Spot Weld StructureExperimental Study of Effect of Adhesives on Strength of Composites Adhesive JointsFracture Behavior of High-Frequency Welded Joints of GH4169 AlloyMechanism Research on Residual Stress's Elimination of Aluminum Alloy Welding by UltrasonicModeling and Analysis of Underwater Wet Weld Process Based on Regression MethodNumerical Simulation Research of Tailor-Welded BlanksOrthogonal Experiment of Resistance Microwelding of Insulated Copper Wire and Phosphor Bronze SheetProgressive Failure Analysis of Adhesively Bonded Laminates Joints with Spew FilletsProperties Effect of 16MnR Steel Weld Joint by Different Welding MethodsResearch on Welded Pipe and Tube Pass Design Virtual MethodsThe Friction Welding Characteristic Analysis of the Al 7075-T6 According to the Spindle Speed and Upset PressureThe Temperature and Residual Stress Distributions of Butt Weld Pass on Nickel Alloy 690 PlateThe Welding Track Planning and Motion Control of T-Type Tube Autowelding MachineThree-Dimensional Numerical Simulation of Temperature Field and Force Field of T-Type Turbe during WeldingVacuum Brazing of Copper Tubes Using Ag-Cu FillerInfluence of Fluctuation Frequency on Stress Corrosion Cracking of X70 Pipeline Steel Welding JointThe Characteristics of Weld Metal Zone Welded with Various Filler MetalsA Method Based on the Morphology of Lead-Free Solder Powder Adhesive Particle SegmentationResearch for Viscoplastic Behaviors of SAC405 Pb-Free SolderA New Method for Minimizing Cogging Torque in Permanent Magnet Machines Using Genetic AlgorithmAb Initio Molecular Dynamics Simulations of Cu under Vacuum and 473~1573KApplication of Interactive Orthogonal Design on the Aerodynamic Drag Optimization of Hatchback CarApplication of Reverse Engineering for Redesigning and Manufacturing of a Printer Spare PartComputerized Numerical Control (CNC) Machining Engraving Processing of Surface Based on Master CAMDesign and Analysis of the Spiral Staircase in Large Steel StructureDesign of Upswept Aft-Body of Civil Transport Based on CFDDiscrete Element Method Simulation of Mesomechanics of Railway Ballast during Tamping ProcessExperimental and Numerical Study of Railway Ballast Compactness during Tamping ProcessFinite Element Analysis of Light Cargo Van FrameFinite Element Analysis of Sealing Structures for SF6 Gas Insulated SwitchgearHand Sketching in 3D Computer Animation Model Rendering and EditingMohr Strength Theory in Simulation Stress AnalysisNumerical Simulation and Optimization of Steel Pipe Cathodic Protection under the Condition of 3.5% BrinePoint-Based CAD/CAM Geometric Model DesignSimulation Calculation of the Braking Performance of Portal Cranes Based on ADAMSSurface Extension in Smoothing of Class a Surfaces for Auto-BodyThe Optimal Design of Injection Mold Gate Based on CAEA New Method to Handle Temporal Planning in Flexible Graphplan FrameworkA Universal Feature Definition Frame for 3-D CAD Model ConversionCombination Regression and Neural Network for Short Term Load ForecastingFour - Wheel Steering Vehicle Modeling and Simulation Based on ADAMSMulti-Dimensional Analysis of NOx and Soot Formation in a Diesel-Fueled Hydraulic Free Piston EngineNew Downhole Intelligent Throttling System Based on the Poppet ValveNumerical Analysis of Flat Circular Parachutes Inflation ProcessPoint Cloud Data Preprocessing Based on the GeomagicResearch on Three-Dimensional Topology Optimization for the Bed of NC Gear ShaperThe Development and Simulation of the 3D FEM Software ---- Alpha SystemThe Reliability Evaluation of Threaded Connections in Challenging Drilling by Three-Dimensional Finite Element AnalysisThe Research of Deformation Compensation of the Unloading Mechanism of the Beam for XK-2535 Large-Scale CNC Gantry Milling Machine and Engineering ApplicationDevelopment of CAD Module for Gating System of Iron Castings Based on SinovationConstruction Method of Tool Path Based on Arc-CellA Parting Surface Design of Multi-Cavity Mold Based on Pro/E Surface TechniqueAir Flow Field and Fiber Motion in a Swirl Die Melt-Blowing ProcessAn Identification Method for Joint Parameters Based on Finite ElementAnalysis on micro-/poly-Crystalline SiGe Alloy Solar CellsDynamics Influences Discussion of Robot MiniQuad-II for Construction Member Structure Change Based on ADAMSEffects of Structural Parameters on Nanofiber from a Multihole Electrospinning SetupNumerical Simulation Analysis on Repairing Hole of UAV WingOptimal Production LineLayout Model Based on Integer ProgrammingResearch and Application of the Structural Optimization Design Technique for the Large and Efficient Band Sawing MachineResearch of Modeling and Simulation of Aviation Ignition EquipmentSimulation of the Nozzle Electro-Hydraulic Servo Valve with ITI-SimulationXSimulation on the Hydraulic System of a Constant Tension Waves Compensation WinchStudy on the Formability Rules with Precise Die Face for the Inner Clutch Shell of AutomobileStudy on the Pressure Distribution on Solid-Plug Conveying of Centrifugal ExtruderThe FEA and Optimal Design of the Loader Based on Virtual PrototypingThe Micro-Variation Principle of Mating Constraints and its Application to Simulation of Cumulative Deviations for Mechanical AssembliesThe Spent Fuel Pool Analysis of Chinshan Nuclear Power Plant by Using TRACE/FRAPCON-3.4The Study of Mechanism Analysis and Dynamical Simulation Based on Ultrasound Enhanced Supercritical and Subcritical CO2 DissolutionDesign and Simulation of Rinsing Equipment of Cable Rolling Wire RopeDesign of Compressed Air Dehumidifying Equipment for Wire Rope and Simulation of Air Knife Flow FieldEffect of High Frequency Electromagnetic Fields on Liquid Steel in Soft-Contact MoldEffect of Insulators on the Power Consumption and the Oxygen Content of Si Ingots in Czochralski GrowthFeasibility Analysis and Simulation of Minitype Combination BalanceFEM Based Numerical Simulation of Delta Parallel MechanismFinite Element Analysis and Experimental Study of an Electromagnetic Shell Part with Flow Control FormingFinite Element Analysis of Frame on ZXZ90 Towing Machine for CableOptimization Design for the Longitudinal Structure of LED Light Guide Plate Using Soft ComputingPartial Least Squares Regression Analysis of Thermal Distortion Behavior for Linear Motor Drive Feed SystemSingle-Machine Scheduling to Minimize Makespan with Deterioration Jobs and Multi-Maintenance ActivitiesSolute Distribution Ahead of Interface during Heteroepitaxial GrowthThe Effect of Damping Block Design on Stability of Ploymer Coextrusion ProcessThe Modal Analysis for the Third Type of Internal Gear MotorThe Simulation Study of the Influence of Surface Error on Optical Properties for Optical PartTheoretical Analysis on Manufacturing Hypoid Left-Hand Gears by Generating-Line MethodCo-Simulation of Composite ABS Control for In-Wheel Motor Drive Electric Vehicle Based on Threshold Control AlgorithmDesign and Analysis of a CFRP Drive ShaftResearch on Vibration and Sound Radiation from Submarine Functionally Graded Material Nonpressure Cylindrical ShellNumerical Investigation for Fracture Saturation in Multilayer Sedimentary Rock in Unsymmetrical CaseNumerical Simulation for Rock Fracturing Process under Action of Disc CutterThe Preventing Coal and Gas Outburst Technology of Middle Distance and Low Permeability and Upper Protective LayerThe Roof Broken Mechanism of Fully Mechanized Coal Face with Super Thick and Loose LayerResearch and Prediction of Yellow Soil Moisture Content in Guizhou Province Based on ARIMA ModelEnergy Analysis and Optimization of Methyl Chlorosilane SeparationThe Optimization of CO2 Huff and Puff Well Location in Ultra-Low Permeability ReservoirPrediction of the Flow, Reaction and Heat Transfer for Glass Furnace Firing Petroleum CokeA Coke Quality Prediction Model Based on Support Vector MachineResearch on Materials Corrosion Failure Model of Liquefied Natural Gas (LNG) Cylinder for VehicleSimulation Studies on the Influence of Impact Velocity on the PELE Penetrated and Broken Reinforced ConcreteThe Failure Finite Element Analysis of Pump Collision with Valve in the Oil Well PumpThe Main Structure Design and Motion Simulation of Spreaders Based on Virtual Prototype TechnologyThe Modal Analysis of the Main Steel Structure of Bucket Wheel Stacker ReclaimerDistribution of Stray Current in the Buried Metallic Pipeline Based on Inducted Electric FieldDesign of Terraced Spinneret Based on Simulation of Electric Field Distribution in ElectrospinningMicro Injection Molding and Strength Check of Polymer Micro-NeedleSimulation Analysis on Height Change of 6010 Aluminum Plate Limit Drawing under Different Process ParametersOptimization and Improvement of Pile and Pull Coefficient Mathematical Model for Trapezoidal Stainless Steel Sieve BarVirtual Processing of Fish FilletsIntegrated Kinematics Optimization and Strength Analysis for a Wheel Loader Boom MechanismNumerical Simulation on Thermal Field in the Fluidized Bed with Internal Heating PlatesModeling and Analysis of the Scavenging System for a Two-Stroke Cycle Hydraulic Free Piston EngineThe Effect and Analysis of the Crankshaft Journal Fillet Rolling for RunoutThe Study of EDG GH3536 Surface Roughness Base on the Artificial Neural Network ModelingThe Damage Evolution of the Flange Repaired Reinforcement LaminatesThe Research on Dynamic Simulation of Rods and Cones Type Docking MechanismReservoir Modeling and Numerical Simulation Controlled by Flow UnitsA New Operational Pattern Optimization Method and Its Application in Nonferrous MetallurgySpectral Element Approximation for the Eigenvalue Problem of Hydrogen Atoms Electronic StructureA Template-Matching-Based Fast Algorithm for PCB Components DetectionAbrasive-Free Polishing of Hard Disk Substrate with H2O2-K2S2O8-NaHSO3 SlurryAspherical Surface Contact Detection Error AnalysisDeep-Hole Precision Honing of Difficult-to-Cut MaterialsEffect of K2S2O8 on Material Removal Rate in Abrasive-Free Polishing of Hard Disk SubstrateElectrochemical Deburring of Miniature HolesNumerical Analysis of the Ultrasonic Honing Chatter Based on the Stribeck ModelQuantitative Analysis of Lateral Setting Error in Two-Point MethodSimulation Analysis of Thermodynamics on the Belt Spindle of the Machining CenterThe Effect of Geometric Error on Machining Accuracy for Machining CenterVirtual Gear Measurement Center and its ApplicationA Novel Method for Kinematic Optimization of Camshaft Non-Circular GrindingComprehensive Test of Electric Spindle Based on Thermal StressEstimation of the Time Constant of Precision Plunge Grinding in Dwell Period Based on Acoustic Emission MeasurementExperimental Investigation on Thermal Characteristics of Hollow Ball Screw in Different Working ConditionsInflection Points Processing of Continuous Tiny Line Segments for CNC System High-Speed MachiningResearch on the Influence of Harmonics on High-Speed Permanent Magnet MotorStudy on Spindle Dynamic Errors of Domestic NC Machine ToolsStudy on Ultrasonic Cavitaion Field of Power Ultrasonic HoningResearch and Application of Dynamic Secondary Cooling Control Method for Slab Caster of CISDIThe Improvement of Laminar Cooling System for Hot Rolled Strip Base on Rolling ProcessExperimental Research on Acoustic Parameters and Saturation of Gas Hydrate-Bearing SedimentsStudy on Flaw Detection in Welding Zone of Diamond Saw BladeStudy on Reaming High-Precision Thin Hole in Hardened Steel by Ultrasonic Vibration ReamerDevelopment of an Automatic Inspection System for Manufacture of Plastic-Container Pump AssembliesFinite Element Analysis of Contact between Laying Head Pipe and High-Speed Wire RodResearch on the Normal Error of Large Aspheric Mirror Employed in Bonnet PolishingDry Sliding Wear Behavior of Laser Clad WC/NiCrBSi Metal Matrix Composite CoatingsNumerical Simulation of Feeding Powder Laser Cladding Temperature Field Based on ANSYSOptimizing BP Networks by Means of Genetic Algorithms in Quality of Laser MillingThe Influence of Mixing Enthalpy on the Geometric Properties of Laser Solid Formed Ti-6Al-4V3D Laser Remanufacturing of Damaged PartsOptimization on Selective Fiber Laser Sintering of Tri-Metallic Powders via Design of Experiments MethodCurrent Progresses of Laser Assisted Machining of Aerospace Materials for Enhancing Tool LifeAnalysis of New Features of Beer Packaging DesignInnovative Vacuum Cleaner Design Using TRIZ MethodResearch & Design of the Multifunctional Landscape Hedge TrimmerAssessment System of Remaining Life for Bridge Crane Based on the Internet of ThingsCharacteristics of Marks on Concave Key Duplicated by MachineConceptual Approach for Design, Fabrication and Testing of Indoor Remotely Controlled AirshipDeficiency Analysis of Different Ship Types Based on Taiwan PSC DataDesign and Experiment of Sinonovacula constricta Purification Bacteria SystemImprovement of Packaging Structure and Materials about Daily Chemical Products Plastic Hose PackagingImprovement of Structure and Material about Plastic Emulsion Pump for Daily Cosmetic Products PackagingOptimization of a 17m Catamaran Based on the Resistance PerformanceResearch on High-Grade Anti-Counterfeiting Scratchcard Invoice Printing Technology and CraftResearch on the Influence Factors of the Wave Collar StyleSCA Based Exploratory Evaluation of Weapon Equipment Operational EffectivenessSlip-Resistance Assessment on Different Types of Emery Anti-Slip StripStudy on a New Type Massage DeviceThe Development of Santana 2000 Lighting Test RigThe Research on the Application of Kansei Engineering in the Product DesignThe Security and Function Improvement of Suitcase Based on Human Factors EngineeringVariation Analysis for a Manufacturing Stage Based on a Balanced One-Way ANOVA ModelWeave and Process Design of Monolayer Two-Sided Velvet FabricResearch on Material Selection and Sizes Optimization of Casing Material for Fracturing Wells under Existence of Brine CorrosionThe Application of Parstat 2273 Electrochemical Workstation in Corrosion ExperimentResearch on Improving the Pass Yield of the Manufacturing of 0645 Type of SharpenerAnalysis of Current Situation of Digital Sculpture DevelopmentAnalysis of Snow-Ice Characteristics and Clearing Performance on Urban RoadExperimental Study on Coal Entry with Water Trickling and Burst Cracked Roof Supported by Anchor NetGaseous Fluorides Formation Mechanism in the Roasting Process of the Fluorite-Bearing Iron ConcentrateMetallogenic Geological Characteristics and Metallogenic Model of Xiachen-Wangchangmu Fluorite Mine in Tiantai Basin, Zhejiang Province, ChinaMine Laneway Modeling and Realization Based on the MatlabSeparate the Anshan-Type Low-Grade Hematite Ore With Process of Low-High Intensity Magnetic Separation and Reverse Flotation MethodStudy on Comprehensive Utilizations of Certain Complex Paragenic Tin Polymetallic OreMechanochemical Activation and Characterization of Low-Medium Grade Phosphorite OreVarious Morphology of Hierarchical Pore-Structured Compound: MCM-41/Diatomite and its Adsorption Behavior for Methylene BluePreliminary Study on Leaching Mechanism of Manganese Using Ternary Compound ReductantGeostatistics Method for Identification of Minor Structure Seismic AttributeLate Accumulation of Kunbei Area in Qaidam BasinStudy on Leaching Manganese from Low-Grade Manganese Ores Using Different ReductantsExperimental Study on Gas Hydrates Dissociation in Sands by DepressurizationLeaching of Low-Grade Manganese Ores by Using Two Compound ReductantsThe Study of the Factors which Influences the Dissolution Rate of the HalitePaste Thickening of Iron Tailings with Vibrating Lamella ThickenerCorrosion Effect of Acid Rain on the Technical Properties of Mineral AggregatesThe Analysis and Correction of Sampling Bias of Discontinuity Orientation Caused by Linear Sampling Technique
