Buch, Englisch, 428 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 800 g
Buch, Englisch, 428 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 800 g
ISBN: 978-3-03835-241-9
Verlag: Trans Tech Publications
Chapter 1: Flowing Parts Hydromechanics, New Designs, Energy and Resource Saving of Pumps and Compressors,
Chapter 2: Bearings and Seals,
Chapter 3: Strength, Mechanical Vibrations and Reliability, Materials and Technology
Autoren/Hrsg.
Weitere Infos & Material
Preface
Chapter 1: Flowing Parts Hydromechanics, New Designs, Energy and Resource Saving of Pumps and Compressors
Study of Flow Pattern in Components of Intermediate Stage Vanes Diffuser of Centrifugal Pump
Determination of Static and Dynamic Component of Axial Force in Double Suction Centrifugal Pump
Modeling of Centrifugal Pumps Operating Modes
Investigation of Energy Losses in the Flow Section of the Small-Sized Axial-Flow Pump
Interaction between Impeller and Axial Diffuser of Mixed Flow Pump
Numerical Approach for Simulation of Fluid Flow in Torque Flow Pumps
The Application of CFD Methods to Analyse the Flow Structures in the Radial Labyrinth Pump
Jet Thermal Compression of the Ammonia-Water Mixture for Heat Pumps and Refrigerating Systems
Jet-Reactive Turbine: Experimental Researches and Calculations by Means of Softwares
Cavitation its Use and Mathematical Modelling
Methods Development for Determining the Aerodynamic Characteristics of Vertical Exist of Wind Turbine
Evaluation of Oil Viscosity Influence on Hydraulic Shock in Long Pipe
Existing Perspectives of Rotodynamic Pumps Rotation Speed Increase
Mining Submersible Pump - Design, Characteristics and Protections
Investigation of Liquid-Steam Stream Compressor
Modeling and Design of Inertial – Filtering Gas Separators-Condensers for Compressor Units of Oil and Gas Industry
Development of Mathematical Model of Working Process of Multi-Functional Heat-Generating Aggregate-Hydromill
Selection of Pumping Equipment for Oil Pipeline Transport
Creating a Standard Size Range as One of the Factors Reducing Production Time of Modern Pumping Equipment
Replaceable Hydraulic Parts in Spiral Volute Pumps
Influence of Operation Mode on Efficiency and Life Cycle Cost of Double Suction Pump
The Design Features of BB4 and BB5 API 610 Pumps for Water Injection Systems
Monitoring of Pumping Unit Operation in Indicators of Energy Efficiency of its Work
Chapter 2: Bearings and Seals
Axial Flow Seal/Bearing Efficient Pressure Formulation for a Reynolds Equation Solution
A Review on Active Bearings and Perspectives of Using Them in Rotating Machinery
Reliability Improvement of Rotor Supports by Combining Rolling-Element Bearings and Fluid-Film Bearings
Effect of Lubrication of Fluid Friction Bearings with Media of Complex Rheology
Solutions for Increasing the Bearing Capacity of Thrust Bearings
Studying the Interaction of Liquid and Solid in the Flow of Liquid in Annulus by CFD Analysis
Simulation of the Working Fluid Stream in the Pumps and Turbines Flow Path Seals
Flow Simulation in a Labyrinth Seal
Analysis of a Nonlinear Elastic Force in a Relatively Long Annular Seal and its Impact on the Dynamics of the Rotor
Static and Dynamic Analysis of the Closing Rotor Balancing Device of the Multistage Centrifugal Pump
The Lubrication Regimes of Mechanical Face Seals
The Calculation of Static Characteristics of Impulse Gas Seal
Proposal to Improve the Design of the Impulse Face Seal
Sealing of Pipelines Flange Connections in Conditions of Fasteners Tightening Torque Reducing
Indirect Method of Leakage Flow Rate Measurement in Compressed Air Pipelines
Oil Lip Seal and Shaft as a Specific Friction Couple
Laser Texturing of Sliding Surfaces of Bearings and Pump Seals
Chapter 3: Strength, Mechanical Vibrations and Reliability, Materials and Technology
Computer Design of Compressor Impellers of Increased Fatigue Strength
Elastic Bellows Prepared by Selective Laser Sintering
Thermal Stress State of Impeller Seal Made from Composite Material
Assessment of the Mechanical Properties of a Diesel Engine Injector
Analysis of the Radial-Axial Oscillations of the Rotor of a High-Speed Pump
Determination of Reliability of Rotor-Annular Seals System by Theory of Runs of Random Functions
Influence of Changing the End Floating Seal Dynamic Characteristics on the Centrifugal Compressor Vibration State
Dynamics of the Interaction between Human Circulatory System and Centrifugal Pump as a Left Ventricle Assist Device
Damping of Self-Excited Pressure Pulsations in Petrodiesel Pipeline
Considerations Regarding the Pumps Vibration Monitoring Using Proactive and Predictive Maintenance Programs
New Method of Friction Assemblies Reliability and Endurance Improvement
Upgrading of Pump and Compressor Rotor Shafts Using Combined Technology of Electroerosive Alloying
