Buch, Englisch, 284 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 640 g
Buch, Englisch, 284 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 640 g
ISBN: 978-3-03785-945-2
Verlag: Trans Tech Publications
Autoren/Hrsg.
Fachgebiete
Weitere Infos & Material
Preface
I. Microstructural Characterisation
Effect of Carbon Addition on the Microstructure and Properties of Unalloyed Titanium
Structure of Aluminium Matrix Composite with Ceramic Preform Obtained by Centrifugal Infiltration Process
Plasticity and Microstructure of Magnesium - Lithium Alloys
TEM and X-Ray Examinations of Intermetallic Phases and Carbides Precipitation in an Fe-Ni Superalloy during Prolonged Ageing
Effect of Solution Treatment on the Microstructure of Ti-C Alloys
Scanning Transmission Electron Microscopy Studies of the Microstructure of High Chromium Steel after Long Time Exposure
Effect of Boron Addition on the Microstructure of Ti-47Al-2W-0.5Si Alloy
II. Advanced Thermal, Mechanical and Chemical Processing
Influence of Heat Treatment on the Hardness of ZnAl22Cu3 Alloy
Dissolution of Carbide Isolates in Acids Using Microwave Technique
The Correlation between the Surface Geometry of Tested Materials and the Shape of Lubricant Drop
Influence of Forming on the Properties of Alloy Based on the Matrix of FeAl Intermetallic Phase
Production Methods of Thin, Narrow and Profiled Steel Strips
Physical and Mechanical Properties of Composites with Aluminum Alloy Matrix Designed for Metal Forming
Influence of Deformation Parameters on the Structure in Selected Intermetallic from Al-Fe Diagram
Estimation of Flow Stress of Zinc-Titanium Strip during Reverse Rolling
Characteristics of the Structure of Welded Joints in Sanicro 25 Steel
Influence of Copper Addition on Structure and Hardness of the ZnAl40Cu3 Alloy after Heat Treatment
The Repair Welding Technology of Casts Magnesium Alloy QE22
High Manganese TWIP Steel - Technological Plasticity and Selected Properties
The Potential and Application Areas of Forging Aided by Shear Stress
Welding of Steel with High Manganese and Aluminum Content
III. Surface Engineering and Corrosion Resistance
The Structure of Coatings Obtained in the Zn-31Al-3Mg Bath on High-Silicon Steel
Liquid Metal Embrittlement of Steel with a Coating Obtained by Batch Hot Dip Method in a Zn + 2% Sn Bath
Influence of the Ion Nitriding Process on the Electrochemical Properties of X39Cr13 Steel Used for Surgical Instruments
Synergistic Influence of the Addition of Al, Ni and Pb to a Zinc Bath upon Growth Kinetics and Structure of Coatings
Investigation of the Initial Stage of Hot Dip Zinc Coatings on Iron Alloys with Various Silicon Contents
Kinetics of Growth and Structure of Coatings Obtained on Sandelin Steels in the High-Temperature Galvanizing Process
Influence of Si and REE on the Corrosion Resistance of ZnAl40Cu3 Alloy
Kinetics of Corrosion Processes of Alloy on the Intermetallic Phase Matrix FeAl in High Temperature in Air Atmosphere
Influence of the Type of Medical Sterilisation on Electrochemical Properties of Passive Layer Created on X10CrNi 18-8 Steel
The Structure and Growth Kinetics of Zinc Coatings on Link Chains Produced of the 23MnNiCrMo5-2 Steel
Influence of Corrosion in "Acid Rain" on the Structure of Surface Layer of the ZnAl22Cu3 Alloy
Gas Corrosion of Chromium-Manganese Steel in Atmospheres with Low Oxygen Partial Pressure
Resistance to Electrochemical Corrosion under Conditions of Sterilisation of Guide Wires Used in Endourological Treatment
Corrosion Resistance of Zn-31AlMg Coatings Obtained by Batch Hot Dip Method
IV. Materials and Environment
Classification and Assessment of Environmental Aspects of Converter and Electric Steel Plants
Evaluation of Refractory Lining of the Blast Furnace Hearth and Bottom in Five Years of its Operation on the Basis of the Isotherms Shapes
Effects of Raw Material Contaminants on the Ferrosilicon Melting Process in the Submerged Arc Furnace
Technological Effects of Metallurgical Industry Restructuring in Poland
Influence of the Steel Scrap Classes on the Liquid Steel Output Melt in Electric Arc Furnace
Utilization of Metallurgical Waste in Non-Metallurgical Industry
Evaluation of the Applicability of Sanicro 25 Steel in Supercritical Boilers
The Influence of Slenderness Ratios of Multi-Hole Ceramic Filters from SF - 1.67 to SF - 8.36 of Filter Surface on Efficiency of Liquid Steel Refining from Non-Metallic Phase
V. Advanced Materials for Transport Industry
Non-Metallic Inclusions in Castings Made of Nickel-Base Superalloys
Metallurgical Quality of Feed Ingots and Castings Made from Nickel and Cobalt Superalloys
Effect of Cooling Rate and Modification on the Structure of Cast AlSi17 Alloy
X-Ray Analysis of the Precipitation Process in an Fe-Ni Superalloy
The Effect of Heat Treatment on Creep Resistance of Castings from the Modified Superalloy MAR-247
Nucleation and Growth of Primary Silicon Crystals in AlSi Alloy after Modification with CuP and Overheating to a Temperature of 920°C
Application of Incremental Metal Forming for Production of Aircraft Integral Panels
Analysis of Cracking Process in Conditions of High-Temperature Creep of Castings Form the Modified Superalloy IN-713C
Porosity in Turbine Blades Cast into New Shell Moulds Made of SiC Based Ceramics
Research on Mechanical Properties of Thin Sheets Blanks Made of Creep-Resisting Nickel Superalloys
Analysis of the Cracking Processes of Jointing Components Used in Turbine Valve Chest
