Selected, peer reviewed papers from the 9th International Conference on Local Mechanical Properties (LMP 2012), November 7-9, 2012, Levoca, Slovak Republic
Buch, Englisch, 286 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 650 g
ISBN: 978-3-03785-876-9
Verlag: Trans Tech Publications
Autoren/Hrsg.
Fachgebiete
Weitere Infos & Material
Preface, Committees and Sponsors
Invited Lecture
Characterization of Polypropylene Staple Yarns by Acoustic Dynamic Modulus
I. Oral Presentation
Development of Plastic Zones during the Thermal Cycle of Welding
Reduction of Elastic Modulus of Titanium Alloy Ti-6Al-4V by Quenching
Measurement of Local Initiation, Early Growth and Retardation of Physically Short Fatigue Cracks Using Amended DCPD Method
Nanohardness of Individual Phases in WC – Co Cemented Carbides
Influence of Loading Conditions on the Deformation Behavior of Human Enamel Studied by Instrumented Indentation
Effect of Crystallographic Orientation on Hardness and Indentation Modulus in Austenitic Stainless Steel
Nanohardness vs. Friction Behavior in Magnetron Sputtered and PECVD W-C Coatings
Estimation of Local Plastic Deformation of Polycrystalline Materials
Determination of the Elastic-Plastic Properties of 15Kh2MFA Steel with Austenitic Cladding
Limitations of Similarity Principle in Indentation Testing of Small Samples
Indentation Size Effects in Ductile and Brittle Materials
Nanoindentation Applied to Materials with an Inner Structure
Mechanical Properties of Aluminum Alloys by Instrumented Indentation: Case Study on Almigo Hard
Experimental Analysis of Local Stress State and Deformation in the Critical Area of Combustion Engine Cylinder
Failure Initiation in Dual-Phase Steel
Design and Verification of Sandwich Structures for High Speed Trains
II. Poster Presentation
Effect of Beta Irradiation on the Strength of Bonded Joints of HDPE
Mechanical Properties of Metal Matrix Nanocomposites Synthesized by Selective Laser Melting Measured by Depth Sensing Indentation Technique
Local Mechanical Properties of Au Thin Films on Polyethylene
Change in Mechanical Properties of Weld Claddings after Cyclic Thermal Loading
Digital Image Correlation Based Method of Crack Growth Rate and Fracture Toughness Measurements on Mini-Samples
Microstructure and Local Mechanical Properties of Cu-Co Alloys after Severe Plastic Deformation
Fatigue Cracking Processes of a Thick-Walled Component of a Chemical Pipeline
Fracture Stress of Ultrahigh Strength Ribbons Determined by Microhardness
Nanoindentation-Induced Phase Transformation in Silicon Thin Films
Local Tribological Characteristics of Steel Sheets for Microforming
Micro-Mechanical Testing of Metal Foam Cell Walls Using Miniature Three-Point Bending
Comparison of the Natural Ageing Behaviour of EN AW 6082 and Lead Free EN AW 6023 Aluminium Alloys
Strain Measurement in Local Volume by Non-Contact Videoextensometric Technique on Ultra High Strength Steels
The Variation of Mechanical Properties of WC-Based HVOF Sprayed Coatings with Respect to the Co Content
Microstructural and Vickers Microhardness Evolution of Heat Treated Secondary Aluminium Cast Alloy
Stability of Superalloys Doped with Rare Earth Elements
A Description of Local Material Properties Close to a Butt Weld
Evaluation of Local Mechanical Properties of Thin Coatings Prepared by PVD Evaporation
Influence of the Filler Root Surface Treatment on Bending Fatigue Test Results of the Hardened Gears
Creep Modified Structural Relaxation of Fe-Based Amorphous Alloy
Effect of Welding Parameters on the Quality of Spot Welds Combining AHSS Steel and HSLA Steel
Mechanical Properties of Porous Si3N4 Ceramics
Local Mechanical Properties of Borides in Fe-B Steels
Determination of Mechanical Properties of Active Solder Alloys Using the Measuring Method “Small Punch Test”
Mechanical Properties of Interface of Heterogeneous Diffusion Welds of Titanium and Austenitic Steel
The Resistance Tests of Glass-Cement Plates in High Temperatures
Material Testing of Natural Stones Used in Historical Buildings Based on Scanning Electron Microscopy and Nanoindentation
On the Indentation Modulus of Sintered Materials
Influence of Interphase Imperfection on Micro-Crack Behavior in Polymer Composites Filled by Rigid Particles
Ionizing Radiation Effect on PMMA Measured by Microhardness
Analysis of Composite Shrinkage Stresses on 3D Premolar Models with Different Cavity Design Using Finite Element Method
Temperature Influence on Microindentation Data of a Viscoelastic Material
Local Deformation of Microsized Amorphous Powder at Low Temperatures
Local Strain and Stress Analysis of Globe Valve Housing Subjected to External Axial Loading
Effect of Beta Irradiation on Microhardness of Polyamide 6
Efect of Cyclic Heat Treatment on Cast Structure of TiAl Alloy
Investigation of Changes in Microstructure of Remelted Air Plasma Sprayed NiCrAlY Coating after Short Thermal Exposure in Air with the Assistance of Microhardness Measurements
The Effect of the Polyamide Reinforcement on Mechanical Properties of Fluorocarbon Rubbers Exposed in Aggressive Environment
Effect of Sterilization Processes on the Fiber/Matrix Interphase Properties of CF/PDMS Composite to be Used in Orthopaedics
Using the Multi-Parameter Fracture Mechanics for more Accurate Description of Stress/Displacement Crack Tip Fields
Local Mechanical Properties of Cast and Sintered High Cr-Alloyed Steel
Experimental and Numerical Analysis of Local Mechanical Properties of Drawn Part
Local Changes of Microhardness in Dissimilar Weld Joints after High Temperature Exposure
Characterization of the Interphase in Carbon Fiber Reinforced Polymeric Composite by a Modulus Mapping Test
Evaluation of Local Plastic Flow in the Vicinity of Indentation by the Means of DIC Applied on SEM Micrographs
Mechanical Properties of Single and Double-Layered PVA Nanofibers
Verification of Numerical Model for Trabecular Tissue Using Compression Test and Time-Lapse X-Ray Radiography Based on Material Model Determined from Three-Point Bending Test of Single Trabecula
