Buch, Englisch, 428 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 700 g
Collection of selected, peer reviewed papers from the 2nd International Conference on Non-Ferrous Metals ICNFM'15 (June 22-24, 2014, Cracow, Poland) which cover a wide spectrum of modern decisions in area of production and use of non-ferrous metals and alloys.
Buch, Englisch, 428 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 700 g
ISBN: 978-3-03835-733-9
Verlag: Trans Tech Publications
Autoren/Hrsg.
Fachgebiete
- Technische Wissenschaften Verfahrenstechnik | Chemieingenieurwesen | Biotechnologie Metallurgie
- Technische Wissenschaften Maschinenbau | Werkstoffkunde Technische Mechanik | Werkstoffkunde Materialwissenschaft: Metallische Werkstoffe
- Technische Wissenschaften Maschinenbau | Werkstoffkunde Produktionstechnik Fertigungstechnik
Weitere Infos & Material
Preface, Organizing Committee, Scientific Committee
Chapter 1: Materials Science: Structure and Properties
Characteristic Structure of Cu-0.8Cr Alloy Using SPD Deformation by Rolling with Cyclic Movement of Rolls Method
Investigation of Homogenization Process of the 5019 Alloy Extrusion Billets
Experimental Analysis of Residual Stress in Friction Stir Processed Cast AlSi9Mg Aluminium Alloy
Influence of the Ageing Temperature on the Microstructure and Selected Mechanical Properties of Ti13Nb13Zr Alloy
Friction Stir Welding of Dissimilar Aluminum Alloys
Study of the Structural Properties and Segregation of Alloying Elements in Strips from the TRC Line
Analysis of the Antimicrobial Copper Alloys Registered by the Environmental Protection Agency
Effects of Thermal Heat Treatment Parameters on the Properties of WE43 Magnesium Alloy
New Aluminum Base Materials for Use on Electrical Purposes
Influence of Sr Addition on the Microstructure and Properties of HPDC EN AC-Al Si9Cu3(Fe) Alloy
The Range of the Occurrence of a Phase in near ß Titanium Alloys
The Porosity Description in Hypoeutectic Al-Si Alloys
Research on the Selection of Heat Treatment Parameters of Casting Aluminum Alloy AlSi5Mg Type
Influence of the Shaping Microstructure Technology and Properties of AlMgSi Alloys on Microcracks Formation under an Influence of Static Compression Loads
Numerical Models of Vacancy Diffusion Based on Crystal Structure
The Effect of Deformation on Microstructure of Cu-Ni-Sn Aging Alloys
Microstructure and Tribological Properties of a Material with Cementite Eutectic Applied for Metallurgical Rolls
Structure Analysis of Magnesium Alloy (AZ31) Wires at Different Stages of a Multistage Cold Drawing Process
Researches on the Production of Conductive Aluminium-Graphene Composites
Research of Chemical Composition Influence on the Mechanical and Electrical Properties of Al-Mg-Si Wires
Computer-Assisted Methods of the Design of New Materials in the Domain of Copper Alloy Manufacturing
Metallographic Studies of Selected Eneolithic and Bronze Age Artifacts from Poland
New Type of Lightweight Railway Overhead Line Carrying Equipment
Chapter 2: Coatings
Protective Coatings on Steel Dies for Wax Injection Process
Selection of Protective Coatings Obtained by Plasma Spraying Method for Foundry Industry
Effect of the Addition of Glassy Carbon on the Structure and Properties of ZrO2-Y2O2 Coatings
Electrochemical Deposition of Selenium on Copper
Chapter 3: Casting and Solidification
Structure and Properties Studies of Rapidly Solidified Al-Mn Alloys
Influence of Continuous Casting Conditions on Segregation of Additions in EN AW 1350 Aluminum Alloy
Investigation of Solidification Process of As-Cast ADC12 in Sand Molds with Different Pouring Conditions by Temperature Field
Study on Rheo-Continuous Casting of Al-Si A356 (EN AC4200) Alloys
Influence of Al and Fe Additions on Structure and Properties of Cu-Sn Alloys
Chapter 4: Powder Metallurgy
Powder Metallurgy and Precious Metals: State of the Art and Future Developments
The Structure and Mechanical Properties of Plastically Consolidated Al-Ni Alloy
The Influence of Process Parameters on Microstructure and Mechanical Properties of PM Al+4 wt. %Cu Alloy
Structure Evolution in Annealed and Hot Deformed AlMg-CeO2 Composite
Influence of Molybdenum and Boron Addition on Fracture of P/M Parts
Copper Metal Matrix Composites Reinforced by Titanium Nitride Particles
Bulk Nanomaterials and Powders Consolidation Produced by Cyclic Extrusion Compression
Recycling without Melting: An Alternative Approach to Aluminum Scrap Recovery
Chapter 5: Metallurgy and Recycling
Hydrometallurgical Treatment of Smelted Low-Grade WEEE in Ammoniacal Solutions
Metallurgy at KGHM Polish Copper SA
Recycling of Nd-Fe-B Magnets from Scrap Hard Disc Drives
Effect of Processing Parameters on Aeration of Reduced Hatinh Ilmenite
Application of CVCC Technique for Measuring Electrical Conductivity of Metallurgical Slags and Molten Salts
Chapter 6: Production Technologies of Non-Ferrous Metals
Functional Model of Monitoring System of Laboratory Tests for Individual Production Supervised in the ERP
Relationship between Copper Price and Selected Metals Prices
World Class Manufacturing Methodology as an Example of Problems Solution in Quality Management System
Evaluation of Local Material Flow during Complex Deformation Conditions on the Basis of Multi Scale Analysis
Application of Torsion Test for Determination of Rheological Properties of 5019 Aluminium Alloy
Plastometric Testing of Rheological Properties of 5083 and 5754 Aluminium Alloy
Research of the Laboratory Wire Drawing Process of Zinc
Microstructure and Creep Properties of Selected Gravity Casting Magnesium Alloys
The Effect of Homogenization and Interrupted Rolling on Microstructure and Properties of Zn-Cu-Ti Rolled Sheets
Changes in Structure and Hardness of CuFe2 Alloy during Rolling with Cyclic Movement of Rolls
Rheological Resistance of CuAg15 Alloy Wires
Analysis of Extrusion Welding Conditions for AlMg Alloys with High Mg Content
