Buch, Englisch, 260 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 580 g
Buch, Englisch, 260 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 580 g
ISBN: 978-3-0357-1530-9
Verlag: Trans Tech Publications
Autoren/Hrsg.
Fachgebiete
Weitere Infos & Material
Preface
Chapter 1: Analysis Properties of Building Materials
Influence of Bottom Ashes from Biomass on Compressive Strength of Concretes
An Experiment Investigation on Physical and Mechanical Properties of High Strength Concrete with Suitable Admixture
Improve Light Weight Concrete Characteristics by Adding Paraffin Wax as Moisture Proof
Effect of Elevated Temperature on Bond Strength of Concrete
Bond Behavior of Low-Activated High Aluminate Concrete with Reinforcement under Cyclic Load
Matera Building Stones: Comparison between Bioclastic and Lithoclastic Calcarenites
Moisture-Density Relationship of Bottom Ash, Lime Stabilized Bangkok Clay as a Potential Pavement Material in Thailand
An Experimental Study on Effect of Lime and Geogrid in Pavement Thickness
Influence of Coating on Mechanical Performance of Lap-Spliced Carbon Fiber-Textile Reinforced Mortar (TRM)
The Influence of Chemical Additives on Strength of Wood-Cement Composite
Influence of Thickness of Air Gap on Concrete Curing in Formwork with Transparent Cover
Heat Treatment of Self-Compacting High-Strength Concrete in Cast In Situ Construction Using Infrared Rays
Chapter 2: Mechanical Properties and Behaviour of Structural Elements
Numerical Analysis of Punching Shear Failure of Self-Compacting Fiber Reinforced Concrete (SCFRC) Ribbed Slabs
Structural Effect of Using Steel Fiber Reinforcement on the Punching Shear of Self-Compacting Fiber Reinforced Concrete (SCFRC) Ribbed Slabs
Influence of the Bauschinger Effect on the Distribution of Residual Stresses in a Thin Hollow Hyperbolic Disc under External Pressure
Design of Timber Single-Span Beam with Steel Reinforcement
Compressive Behaviour of Laminated Neoprene Bridge Bearing Pads under Thermal Aging Condition
A Deployable Brace Model with Joint Clearance and Strut Eccentricity in Seismic Design
Evaluation for RC Column Confined Partially with Externally FRP Wrapping Sheet Using Nonlinear FE Analysis
Strength and Deformability of Reinforced Concrete Beams with Indirect Reinforcement in the Form of Welded Meshes in Compressed Zone
Conical Round Tubes - Preliminary Tests for Use on Lighting Columns
Mechanical Behaviour of Composite Material Based on Mortar/Natural Fibers (Fique "Furcraea andina") Meshes as External Reinforcement of Concrete Beams
Chapter 3: Polymers and Composites
Study on Dispersion Stability Characteristics of TiO2 Nanoparticles in PCM for Use in Cold Storage Air-Conditioning
A Study on the Effect of Argon-Oxygen Plasma Treatment on Ultra-Thin Expanded PTFE Membrane
Morphology, Mechanical and Thermal Properties of Poly(Lactic Acid)/Propylene-Ethylene Copolymer/Cellulose Composites
Improvement of Poly(Lactic Acid) Properties by Using Acrylonitrile-Butadiene Rubber and Polyethylene-g-Maleic Anhydride
Anti-Counterfeiting Layer of 2D Colloidal Crystal Based Photonic Material
Preparation and Photocatalytic Properties of Graphene/SrTiO3 Thin Film Catalyst
Chapter 4: Materials Processing Technologies
Comparison of Different FEM Software in Terms of Hot Ultrasonic Assisted Machining Technique
Research on Technology of Welding Aluminum Foil in Pressure Vessel Based on Ultrasonic Rolling Welding
Investigation of Arc Bubble Affecting the Arc Stability and Improvement of Weld Appearances Using Bubble Constraint Device in Underwater Wet Welding
Parametric Study of Underwater Laser Welding on 304 Austenite Stainless Steel
Surface Modification of Steel by Anodic Plasma Electrolytic Boronitriding and Polishing
Deterioration Characteristics of Overlapping Layers between Al-5Mg Thermal Spray Coating and Heavy-Duty Paint Coating
Preparation and Drilling Performance of Orderly Arranged Diamond Bit
