Advanced Materials and Manufacturing Processes

International conference on Advanced Materials and Manufacturing Processes (ICAMMP 18)
Erscheinungsjahr 2018
ISBN: 978-3-0357-1363-3
Verlag: Trans Tech Publications

Buch, Englisch, 224 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 520 g

Articles, collected in this volume, present the results of research in the fields of modern structural materials and technologies of their machining. The collection was created by the results of the International Conference on Advanced Materials and Manufacturing Processes (ICAMMP 18).

Autoren/Hrsg.

Swami Naidu, Gurugubelli

Sivaprasad, K.

Fachgebiete

• Technische Wissenschaften Maschinenbau | Werkstoffkunde Produktionstechnik
• Technische Wissenschaften Maschinenbau | Werkstoffkunde Technische Mechanik | Werkstoffkunde

Inhaltsverzeichnis

Preface
Chapter 1: Advanced Composites
Mechanical and Morphological Properties of Epoxy Based Hybrid Composites Reinforced with Banana-Pineapple Fiber
Experimentation and Analysis on Reinforced Basalt and Carbon Fibres Composite Laminate
Evaluation of Mechanical Properties of GFRP Composites Reinforced with Single Wall Carbon Nano-Tubes by Immersion in Normal and Sea Water under Hydro-Static Pressure
Effect of Blast Furnace Slag and Red Mud Reinforcements on the Mechanical Properties of AA2024 Hybrid Composites
A Review on Mechanical and Acoustic Emission Behavior of Basalt Fiber Reinforced Composites
A Review on Acoustic Emission Characterization of Failure Modes of Carbon Fiber Reinforced Composites
Dynamic Mechanical Analysis and Thermo-Gravimetric Analysis on Chopped Strand Mat Reinforced with Polyester Resin and Graphite Powder
A Review of Recent Developments in Natural Fiber Composites and their Mechanical, Thermal & Machinabilty Properties
Chapter 2: Properties and Machining Technologies of Structural Steels and Alloys
TEM Analysis of Precipitates in a Low Alloy Wear Resistant Steel and Correlating with its Corrosion Behaviour
Equal Channel Angular Extrusion of AA 5083
A Combination of H3BO3 (nm) and TiO2 (µm) Nano/Microparticle as an Additive to the MQL Enhances the Performance of Cutting
Utilization of Ring Compression Test to Investigate the Mushroom Effect and Adhesive Nature of AA2014 Billets
Low Cost Vibration Measurement and Optimization during Turning Process
Evaluation of Process Parameters in Machining of AA6063 Alloy
Experimental Investigation on the Performance of Vortex Tube
Effect of Heat Treatment of AZ91 Magnesium Alloy on the Electroless Ni-P Deposition
Evaluation of Coefficient of Thermal Expansion of Zirconium by Using Dilatometer & Ansys
Influences of Varying Current by Tungsten Inert Gas Welding and its Process Parameters on Weld Quality of AA 6061 Aluminium Alloy
Simulation Studies and Evolution of Mechanical Properties of AA6061 Subjected to RCS
Direct Active Soldering of PEO Coated and Uncoated AA6061 Aluminium Alloy
Effect of Electrolyte on Micro Arc Oxidation Coating of Al-2014 Alloy
Studies on Dissimilar Friction Stir Welded Al–4Cu–TiB2 In Situ Composites with Base Alloy
Experimental Investigation on Friction Stir Butt Welded Aluminium 6061-T6 Alloy Using Taguchi L9 Experimental Approach
Magnetic Non-Destructive Evaluation of Softening of Cold Rolled Low Carbon IF Steel
An Experimental Study on Mechanical Behaviour of Pulsed Current Welding on Aluminum Alloy Joints
A Feasibility Report on the Comparsion of the Characteristics of Manufacturing a Bearing Cover by the Processes of Sand Casting and Shell Moulding

Über Autor(innen)

Eds. Swami Naidu Gurugubelli and K Siva Prasad