Buch, Englisch, Format (B × H): 170 mm x 240 mm, Gewicht: 2800 g
Buch, Englisch, Format (B × H): 170 mm x 240 mm, Gewicht: 2800 g
ISBN: 978-3-03785-501-0
Verlag: Trans Tech Publications
Autoren/Hrsg.
Weitere Infos & Material
Preface and Conference Organization
Chapter 1: Machine Design and Analysis
Research on Modeling and Simulation of Electric Power Steering System for Electric Power Bus
Kinematic Characteristics and Optimization Analysis of Oval Geared Hoeken Mechanism
Modeling and Analysis of Joint Motion of the Rope and Trolley in Crane System
Design and Performance Analysis of Yielding Anchor Bolt with Large Deformation
Design of a Hybrid Magnetic Bearing Based on Equivalent Magnetic Circuit Method
Study on the 4-PTT Variable Topology Parallel Chinese Massage Manipulator
Study on Oblique Cam Type Mechanical Torsional Vibrator
The Improved Research of the Defrosting of an Automobile Windshield
Study on Magnetic Suspension-Type Needle Driving Model for a New Knitting Device
Optimizing Design System of Four Linkage Mechanism in Hydraulic Support Based on VC + +
Optimum Design for Improvement of Roller Bearing Load Distribution in a Medium Scale Mill
Design Optimization of the Flexspline in Harmonic Drive
Design of Three-Dimensional Parallel Vibration Casting Machine
Structure Analysis to the Rotary Wheel of a Tire Testing Machine
The Research for the Piezoelectricity Rain-Removing System of Rearview Mirror
Finite Element Analysis and Optimizing Design of the Bus Body
Assembly Planning Method Based on Design Structure Matrix
Optimal Design of the Rubber Chain Attached Board Used in Steel Wire Knitting Machine Based on ANSYS Workbench
Reliability Analysis of Over-Center Locking of Mechanism
Application of Orthogonal Experiments in Simulation and Optimization of Jaw Crusher on Traveling Characteristic Value of Moving Jaw
Optimization Design and Simulation of Negative-Pressure Removing-Chip Mechanism of Deep Hole
The Design of Slope Mower
Optimization Design of Rolling Bearing Based on Reliability Assessment
Structural Design of Banana-Stem Shattering and Returning Machine
Low Cost CPM Machine for Knee Joint
Optimization Design of Trusses Based on Covariance Matrix Adaptation Evolution Strategy Algorithm
A General Method for Synthesizing Straight-Line Linkage with Ball and Burmester Points
Study on Field Seedling Raising Vacuum-Vibration Tray Precision Seeder’s Horizontal Adjustment Mechanism
Comparison Research on Two Luffing Mechanisms of Lemniscate Type Crane
Design and Realization of the Optimization System for ZLZ/ZLY Reducer
Instance Analysis on Designing Method of the Transmission Multi-Cones Synchronizer
Simulation Analysis of the Working Process of the Corn Seed Metering Device with Combination Inner-Cell
Finite Element Analysis of Portable Exoskeleton Based on Ergonomics Parameters Model
Optimization Analysis Based on the Articulated Structure of Cement Floor All-Terrain Vehicle
Minimizing Surplus Parts in Selective Assembly Using GA
Simulation Analysis and Optimization Study on Automotive Air Suspension
Structural Parameters Optimization of Parallel Stable Platform Based on Physical Programming
Design Parameters Optimization of Cutting Head of Cantilever Roadheader Based on Genetic Algorithm
Research on the Design Method of Component-Based Modular Fixture
Analysis on Load Distribution of Needle Bearing Considering Misalignment
A Novel Radial Telescopic Tire Building Drum and its Kinematics Design
New Approach for Spatial Mechanism Synthesis with the C-S Binary Crank by Adaptive Saddle-Fitting
Structural Design of the Vermicelli Strapping Machine
A Study on the Automatic Feeding Device for Optical Fibre Adapter Base
A Conceptual Design of the Knee Rehabilitation Device
Propellant Filling Equipment Simulation for Virtual Assembly
The Design and Preparation Process of Aluminum Silicate Fiber Paperboard Machine
Design Optimization for Double-T Root and Rim of Turbine Blade with Three-Dimensional Finite Element Method
Research on Verfiable Design Model for Design Defect of Mechanical Assembly
Numerical Investigation to the Impact of the Shape of the Front Part on the External Flow Field for a Heavy Duty Vehicle in Crosswind
Analysis and Optimization Design of Raking Coal Manipulator Based on ANSYS
The Kinematics Analysis of Double Crank-Slider Mechanism Based on Simulink
Study on Design of Ratchet-Pawl Clutch in Winder
Similarity Assessment for Assembly Model Based on Component Attributed Relational Graph Matching
Optimization Design and Numerical Simulation for Aerodynamics Shape of an Aircraft
The Innovation Design of the Molding Method and Machine about Non Spherical Sweet Dumpling
Type Synthesis of Torsional Mass Dampers as Anti-Galloping Devices by Using Planar Four-Bar Mechanisms
Aerodynamic Optimization of Variable Pitch Wind Turbine Blade Based on Adaptive Genetic Algorithm
A Novel Two Degrees of Freedom Rotational Decoupled Parallel Mechanism
Design of the Lower Extremity Rehabilitation Robot Communication System
Study on Interference Fit of Composite Flywheel Rotor
A Multiply Function Device for Self Protection (Especially for Females)
Parametric and Optimum Design of Cylinder Mechanism Based on Statics and Modal Analysis
The Data Analysis and Decision of Designation and Optimization on Incline Car Brake Equipment
High Efficient Viscoelastic Damper for Heavy Trucks
A New Method of Gear-Position Decision for Automatic Manual Transmission of Parallel Hybrid Electric Bus
Simulation Study of Kinematic Characteristic for Torsion-Beam Rear Suspension of Automobile
Study on the Vibration Lamella Thickener and its Application in Mineral Processing Plant
Principle and Approach for Determining the Reasonable Cross-Section of the Solid-Web Double-Beam Component
Chapter 2: Product Design and Development
‘Practical Utility’: A Design Concept of Immaterial Society
The Study on the Smart Reference of Movie Arts Applied in Dress Design
Method of Genetic Algorithm Optimization Design of Permanent Magnet Retarder
A New Technology of Producing Color Gradient Products
A Design Method Based on Extraction of Key Points of the Contours of Agricultural Machinery’s Internal Structure: A Case Study on the Design of a Small Self-Propelled Square Baler
Application of Ergonomics Principles in the Packaging Machinery Design
An Optimal Design Procedure for Golf Clubhead Considering Impedance Matching
Design and Parameterized Virtual Simulation Test of a Kind of Seat Bench for Ergonomic Test
Optimum Design of Planar Four-Bar Linkage for Scheduled Tracks
Cab Conceptual Design for the Equipment System Used for Passenger Car Ergonomic Design and Evaluation
A New Algorithm for Determining the Optimal Parameters of the Spring of a Slider Cell-Phone
Aircraft Product Data Traceability Technology Based Workflow
Uneven Granular Module Clustering and Intelligent Optimization for Customizable Products
Optimization Design on Vibration and Noise Reduction of Damping Sandwich Circular Saw
An Aero-Thermo-Elasticity Method Applied on the Supersonic Aircraft Model
Research on Sprayer Innovative Design Based on Ergonomics and Rapid Prototyping
Optimized Design and Experiment of the Jatropha-Nut Huller
The Effects of Background upon Engineering Design Expertise – A Sino Occidental Comparison
Study on Development & Design of Product Service System
The Application of the Expansion Lever Method
Gravity Torque Balancing Device’s Optimization Design of Prosthesis’s Shoulder Based on Nonlinear Programming Genetic Algorithm
Users’ Requirements and Preferences in the Success of a New Product: A Case Study of Automotive Design
Product Evaluation in Stages Based on Robust Design
Conception of Innovation of the Electric Vehicles
Finite Element Analysis of Bicycle Saddle Based on Ergonomics
On Auto Brand Mark Design
Mechanical Products Conceptual Innovation Design by Application of Enhanced Genetic Algorism
Optimizing Study of Top Beam Structure of Electrostatic Precipitator Casing
Application Research on TRIZ Technical Contradiction Solving Principles in Tank’s Protective Armor
The Modeling Design of Health Bedding
Maintenance for the Mirror Systems of LAMOST Telescope
Analysis of Cold Protective Clothing’s Design and Market - Functional & Structural Design
The Study of the Furniture Design Based on Product Morphological Semantics
Resource Configuration for the Collaborative Development of Product
The Suit Pattern Optimal Design Based on the Features of Middle-Aged Women’s Body Shape
Research of Product Form Design Based on Comprehensive Product Processes
Carbon Reduction Technique Used in Panel Furniture Design & Manufacturing
Diagnostic Strategy Optimization Based on Particle Swarm Algorithm
The Conceptual Design of Exercise Washing Machine Based on Trimming
The Research and Application of Innovative Approaches Based on Cognitive Processes
The Analysis Technology of Parameters Change Impact Based on the Product Interface Coupling Network Model
Modulus Packaging Design of the Cylindrical Ceramic Furnishings
Evaluation Model for Product Green Design Based on Active Remanufacturing
Study on Evaluation System Based on the Reconfigurable and Modular Design
Study on Mix-Variable Collaborative Design Optimization
Pedigree Based Product Conceptual Design
Prototyping in the Product Interface Design
Finite Element Analysis and Optimization of Wave-Frame Based on ANSYS
Product Pedigree Based Conceptual Structure Evolutionary Design
Research on Product Cooperation Design for Knowledge Management
Research on Multi-Objective Decision-Making of Materials Selection for Green Manufacturing
An Analysis of Apparel Products Development Process Model: From the Prospective of Integrated Design
Chapter 3: Reverse Engineering
Sorting of Section Contour Data Based on Linear Quadtree
An Integrated Reverse Modeling Approach Based on Reconstruction of Features and Constraints
The Reconstruction of Model and Analysis for Vortex Disk of Scroll Compressor Base on Reverse Engineering
Rapid Prototyping Design of 3D Models by Reverse Engineering
Study on Surface Refactoring Based on Reverse Engineering Software - Imageware
Surface Reconstruction Based on the 3D Laser Scanner
A Novel Mesh Segmentation Method for Conventional Engineering Parts in Reverse Engineering
Modeling and Numerical Control Machining of the Mould of a Rearview Mirror of a Motorcycle Based on the Reverse Engineering Technology
Multi-Degree Reduction of DP Curves with Constraints of Endpoints Continuity
An Image Fusion Assessment Metric Based on Multi-Scale Structure Similarity
Chapter 4: Structural Strength and Robustness
Pre-Reinforcement Technology in Broken Roof Side Condition
Simple Nonlinear Static Analysis Using Truss Models for Modeling Snap-through of Thin Shallow Arches
Modal and Structural FEM Analysis of a 50 ft Pleasure Yacht
Fatigue Analysis and Simulation on Engine Case
The Optimal Method of Structural Reliability and Implementation of MATLAB
Structure Analysis of the Subframe in ZJZ3250 Self-Dumping Truck Base on Finite Element Method
Vibration Analysis of Main Shaft of Paper Advance Mechanism Based on Laser Doppler Vibrometer
Finite Element Analysis of Drive Axle Housing with ANSYS Workbench
The Co-Simulation and Experimental Study of Truck Crane Telescopic System
The Kinematic Analysis and Simulation of the Large-Scale Linear Vibration Screen
Vibration Analysis of Needle-Punching Machine Slider-Crank Mechanism
Multi-Objective Optimization of a Large-Span Wing Analog Beam with Variable Cross-Sections
Experiments on the Vibration Control of Flexible Rotor Using Shear Mode MR Elastomer Damper
One Dimensional Finite Element Method for Continuous Curved Box Girder Including the Shear Lag Effect
Fatigue Reliability Analysis of Turbine of Turbocharger Based on the Endurance Test Profile of Engine
Simulation-Based Reliability Analysis for Kinematic Accuracy of Retracting Mechanism of Landing Gear
The Finite Element Analysis of Derrick of Coal-Bed Methane Rigs
K Value Calculation of Central Crack Plane Using FRANC2D
Development of Central Minute Cavity in the Workpiece of Cross Wedge Rolling
A Type of Bomb Falling Analysis and Reliability Verification
Design and Analysis of Anchor Pegs in Cemented Acetabular Cup
Theoretical Research on Deformation of Porous Material in Air Bearing
Design of a Dynamic Stall Test Rig
The Ultimate Bearing Capacity of Partial Concrete Encased Steel Strengthened Column
Modal and Local Modal Analysis of High Speed Train Car-Body
Reliability-Based Robust Design for Mechanical Components under Small-Sample Information
Fuzzy Reliability Analysis on the Kinematic Precision of Mechanism
Study on Fault Diagnosis of Gear Transmission which is Based on ADAMS
Research on Modeling Method for Equipment Maintenance Strategy Based on Reliability and Residual Life
The Fatigue Reliability Evaluation & Improvement of the Single-Arm Subway Current Collector
Experimental Investigation of Mechanical Press Dynamic Behaviors by Ram Displacement Waveform Curves
The Finite Element Analysis on Can Coiler of Gilling Machine
The Analysis and Research on the Influence of Machining Center Stiffness because of the Bolt-Connection
Finite Element Analysis of the Nut-Supports Subassembly Based on ANSYS
Vibration Response Analysis and Experiment on 2.0 MW Wind Turbine Gearbox
Research on Roll Bending Forming Dynamic Linked List Model and Intelligence Deformation Analysis
Finite Element Analysis on Structure of a New Torsional Vibration Damper
Study on Reliability-Based Optimal Design of Multi-Stage Planetary Gear Train in Wind Power Yaw Reducer
The Mechanical Stress Analysis of the Converter Trunnion Ring Based on the Pro/E and ANSYS
The Structure Design of Special-Shaped PDC Reinforced-Cutter and its Finite Element Method Analysis
Research on the Influence of Hole Arrangement on Ring Die Strength
Reliability Estimations for Liquid Rocket Engine under Asymmetric Loss Function
Analysis on Mechanical Properties of Instrumented Indentation Tester Frame
Chapter 5: Dynamics of Mechanical System
Simulation of Dynamic Properties of ER Damper
Stability Problems of Frequency-Converting Rotation Dynamics on Concrete Mixer
Dynamic Characteristic Research of Planar Four-Bar Mechanism with Joint Clearance
Coupled Dynamic and Vibration Analysis of Beveloid Geared System
Modeling and Optimization Research of a Planar Six Bar Mechanism
Study on Dynamic Performance of Linear Direct Drive Based on Pole Placement
Redesign of Dynamic Balance of Impact Rammer and Study on New Type
An Analysis of the Lateral Dynamic Response of an Axially Moving Cantilever Beam under a Moving Mass
Finite Element Analysis of Motion Gesture for Four-Legged Walking Robot MiniQuad-1
Study on Dynamic Simulation Input Form of Locomotive Wheel Flat
A Harmonic Response Analysis of Food Refrigeration Compressor Based on Abaqus
Dynamics Simulation Study on 3-TPS/TP Parallel Robot
Feasibility Research of Crank-Group Driving Mechanism
Study on the Tractive Ability of Lunar Rover Wheel by Discrete Element Method
Kinematic Matrix Method of Portal Crane Boom System
Dynamic Simulation Analysis of Asymmetric Involute Gear Drive System
Estimating of Aerodynamic and Analysis of Aeroelasticity for Hypersonic Projectile
Dynamic Simulative Study of Hoisting System of Mine
Dynamic Balance Analysis of Automobile Drive Shaft Based on Solidworks
Numerical Study on Aerodynamic Performances of CRH3 under Crosswind
Parametric Analysis of the Dynamic Response of Hot-Rolled H-Shaped Steel Beam under Lateral Impact Load
Simulation Study on Planetary Bevel Gear CVT System Based on Virtual Prototyping Technology
Finite Element Simulation in the Dynamics Calculation of Bolted-Joint Interface
The Transmission System Dynamic Analysis Considering the Gear Installation Error of the Planet Gears for Ravigneaux Automatic Gearbox
Virtual Design of a New Type of Entertainment Machine and Dynamics Simulation of the Conveyor Track
Research on Dynamics of Double-Mesh Helical Gear Set
Stress Solutions of some Axisymmetric and Non-Axisymmetric Cases with the Principles of Elasticity: A Review
Design and Aerodynamic Assessment of Diffuser with Longitudinal Separators for Underbody of Sedan
Analysis of the Damping Properties of High-Transmission-Ratio Cycloidal Drives
Study on Ride Comfort of Non-Linear Vehicle Vibration System
Chapter 6: Transmission Machinery
Parameter Design of Less-Teeth Gear Transmission
The Synchronizer Performance Test of a Manual Transmission
Efficiency Sensitivity of Two-Stage Planetary Gear Transmission System Based on Graph Theory
Parametric Modeling for Spiral Bevel Gear Based on PRO/E
The Gap Nonlinear Characteristics of Gear Transmission System under External Excitation
Research on Modeling and Ratio Control Based on Axial Displacement Feedback for CVT
Calculation Equation of Tooth Face of Shaping Gear for Logarithmic Spiral Bevel Gear
With the Backlash Dynamics Simulation of a Crank-Slider Mechanism of the Internal Combustion Engine
Development and Design on the Rubber Conversion Track Wheel
Design and Simulation on the Rubber Conversion Track Wheel of the Loader
The Mechanism Analysis of Horizontal Vibrated Conveyor with Inclination
Research on Knowledge Representation in Choosing Mechanical Transmission Type
Chapter 7: CAD/CAM/CAE
Research on the Connection Performance of Variable Pitch of Screw Threaded Casing Based on 3D Finite Element Simulation Model
Numerical Simulation on Induction Heating Process for Crankshaft Shrink Fitting
Application of ANSYS Program in Ductility Analysis of Reinforced Concrete Frame Structure with Specially-Shaped Columns
Numerical Simulation of Uprooting of Cassava Root
Numerical Simulation of Digging Shovel Operation of Cassava Root
Frequency Analysis and Optimization Design of Car Powertrain Mounting System Based on ADAMS
The Analysis on the Typical Parts in F1 Race Car
Parametric Modeling of Whole Tower Crane Based on ANSYS
SolidWorks Chain Drive Design and 3D Modeling Techniques
Calculation for 180 Ton Tilting Torque of Converter Based on SolidWorks
Numeral Simulation Study on Pipeline Corrosion Defects under Different Sizes and Pressures Based on FEM
Describing NC Smooth Path Based on the Adjustable Form of the Cubic Spline Interpolation Function
Exploration of Revolved Parts Modeling Based on MBD and Pro ENGINEER
Research on the Recognition Method of Exploded Dimension Based on 2D Engineering Drawings
Computer Aided and Reversed Design of Auto Fans
Fuzzy Finite Element Applications in the Waste Heat Boiler
Modeling and Simulation Technology of Complex Mechanical Systems
Numerical Simulation of Aluminum Alloy Wheel 13° Impact Test Based on Abaqus
Finite Element Analysis for Cycloid Gear and pin Teeth of FA Cycloid Drive Based on ANSYS
Further Exploring CFD-Based Gust Response of the Powered Parachute
A Multiresolution Fairing Approach for NURBS Curves
The Development Style for Overhead Crane CAD System
Modeling and Simulation of Aircraft Nose Landing Gear Emergency Lowering Using Co-Simulation Method
Modeling of 2D Layout Design System Based on Convex Hull Plus Rubber Band Analog
Design and Simulating Analysis of Compressed Garbage Transport Truck Lifting Mechanism Based on ADAMS
Study on Numerical Simulation of Bench Blasting and its Elevation Amplification Effect
A Connecting Method for Offset Contour of Planar Polygon
Design of Turning Area for LNG Terminal Base on Computer Simulation
The Design and Analysis of Closed-Coupled Exhaust Manifold
The Modeling of Rubber Sealing Ring of Fluid Dynamic Pressure and Finite Element Analysis about Stress Based on SolidWorks and ANSYS
Chapter 8: Complex Electro-Mechanical System Design
A Novel Real-Time Algorithm for Torsional Vibration Mode of Generator Sets Based on Rotation IIR Filter
The Synthetic Evaluation Method of the Dynamic Performance and Economic Performance of Battery Electric Vehicle Based on Principal Component Analysis
Research on Automatic Verification Device for Vehicle Sideslip Tester
Research on Complex Precision Mechanical System Assembly Parallel Control System
Research of Phase Compensation Technology in Electronic Instrument Transformer
Robust Suboptimal Control of an Electro-Hydraulic System with Variable Supply Pressure
Terramechanics Model and Motion Control Strategy Simulation for down-Slope Travel of a Lunar Rover
Effect of Mean Wind Speed Variations on Power Generation of Wind Farm
The Electric Field Characteristics Analysis of Converter Transformer Considering Anisotropic
Study on Case Library of Parameterized Aero-Engine Overall Structure
A Study on Parameter Design of Powertrain for Extended-Range Electric Vehicle
Experimental Study of Vertical Axis Wind Turbine with Wind Speed Self-Adapting
Research on Simulation of SRM Drive System Based on Simulink
