Selected, peer reviewed papers from the 2012 International Conference on Materials and Manufacturing Research (ICMMR 2012), December 1-2, 2012, Manila, Philippines
Buch, Englisch, 700 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 200 g
ISBN: 978-3-03785-619-2
Verlag: Trans Tech Publications
Autoren/Hrsg.
Fachgebiete
Weitere Infos & Material
Preface and Organizing Committee
Chapter 1: Materials Science Engineering and Materials Processing Technology in Manufacturing
Effect of Different Concentrations of Nitric Acid on the Conductivity of Single-Walled Carbon Nanotube Transparent Films
Graft Polymerization of L-Lactide onto Cellulose in Ionic Liquid via Twin Screw Extruder
Synthesis and Characterization of Nanoscale Fe/Ni Alloy Particles by Hydrothermal Method
Effect of Carboxymethylcellulose on Plasticized Polylactide
Performance of Dye-Sensitized Solar Cells Using ZnO-Natural Dyes from Sappan Wood, Noni Leaves, Safflower and Black Rice
The Anti-Inflammatory Effects of Tetrandrine-Loading Poly(L-Lactic Acid) Film In Vitro
Flexural Toughness of Sprayable Strain-Hardening Cement Composite (SHCC) for Seismic Retrofit of Non-Ductile Reinforced Concrete Frames
Shear Reinforcing Influence of GFRP Shear Connectors in the Concrete Sandwich Wall Panel (CSWP) for Exterior Envelopes of Buildings
Effect of Cement Matrix’s Type on the Shear Performance of Lightly Reinforced Squat Shear Walls Subjected to Cyclic Loading
Effect of GFRP Shear Ties on Shear Behavior of Interfaces between Precast Concrete Panel and Extruded Polystyrene Special Insulation
Nanosilica and its Future Prospects in Concrete
Study on Cross-Linking Degree of Polyethylene
Cytocompatibility Comparative Study of Hydroxyapatite Coating on Titanium Alloy Treated with Two Chemical Routes
Microstructures and Mechanical Characteristics of Enamel and Dentin of Primary and Permanent Teeth
Study on Corrosion Resistance and Cytotoxicity of the Fluoropolymer Thin Films on Titanium Alloy Surface
Effect of Different Graft Polymerization Systems on Surface Modification of Aramid Fibers with G-Ray Radiation
Physical Properties and Mechanical Behavior of Cement Mortars Containing Waste Tire Rubber Particles
Application of Adaptive Wavelet Thresholding to Ultrasonic Signal Compression of Aluminum Alloy Forgings
Fabrication of Multi-Level Photoresist Patterns in One-Step Lithography by Using Cr/Ni Multi-Film Thickness Mask
Effect of NiO Nanoparticles on Magnetic Polymer Electrolyte for Dye-Sensitized Solar Cells
Aging Behavior of Semi-Solid Mg-10Al-0.3Mn Alloy by the Hot Extrusion
Effect of Al2O3 Capping Layer in ZnO TFT Fabricated by Atomic Layer Deposition
RF Characteristics of SiO2/HfO2/SiO2 MIM Capacitor
Dielectric Relaxation and Reliability of Al2O3-HfO2-Al2O3 Sandwiched Metal-Insulator-Metal (MIM) Capacitor
Polycrystalline Silocon-Oxide-Nitride-Oxide-Silicon Flash Memory on SiO2 and Si3N4 Buffer Layer for System on Panels Application
Estimation of Tension Force in Short Hangers Using Added Mass Method
A Novel Patternable Electrophoretic Polymer Coating for Sidewall Packaging in Microelectronic Devices
Investigates of Fabric Coating Approaches: Process and Observation
Investigates of Fabric Coating Approaches: Parameters for Fabric Performance
Chemical Recycling of Epoxide-Anhydride Hardened Networks Using Near-Critical Water
Structure and Performance of Fe-Al Alloy Layer for Twin Wire Surfacing on the Steel Substrate
Morphology of PANI on Paper
The Thermal Hysteresis of the Type I Antifreeze Protein ‘HPLC-6’: The Effect of Small System
Performance of Granular Media from Blast Furnace Slag on Beer Wastewater Treatment
Optimization on Parameters of Resistance Spot Welding Process for Galvanized Steel Plate
Study on Nonlinear Cutting Forces Phenomenon of Difficult-to-Machining Materials
Residual Stress Profile of Ultra High Strength Low Alloy Steel Induced by High Speed Milling Process
Research on Plasma Spray Particle Impact Matrix Process Simulation
A Study of the Effect of Mineral Particle Shapes on Breakage Rate in Ball Mill Using DEM
Tensile Strength of Cu Sheets Welded by Ultrasonic Metal Welding
Experiment on the Fabrication of the Ni-Fe Micro Structure
Experiment on Electroforming Ni-Fe Property for Micro Fabrication
Slow-Release Carbon Source Composite Materials’ Preparation and Used for Denitrification in Groundwater
Machining Conditions Effect to Machining Temperature and Forces in Orthogonal Machining of Bone
Numerical Analysis of Debonded Honeycomb Sandwich Structure under Compressive Load
In-Fiber Mach-Zehnder Interferometer Fabricated by Femtosecond Laser
Effect of Polyaniline Doping on Structural and Vapor Sensing Properties of Tungsten Organometallic Thin Film
Investigation of Honeycomb Sandwich Composite Structure with Pre-Damage under Uniaxial Compression
Twinning Stress in Fcc Metals from the Classical Nucleation Theory
Chapter 2: Design, Modelling, Simulation in Manufacturing and Mechanical Engineering Applications
Effects of Grinding Parameters on Creep Feed Grinding
Explorative Study and Prediction of Overtempering Region of Disc Heated by Induction Process Using 2D Axisymmetric Model and Experimental Tests
Simulation of Helical Gear Heated by Induction Process Using 3D Model
Apply of Industrial Engineering Techniques for Cost Reduction in Frozen Food Industry
Numerical Simulation of Flow and Heat Transfer during Filling Process Based on SPH Method
Simulation Study and Application on HPDC Process with Automobile Part
Error Modeling and Iterative Algorithm for Compensation Instructions of Five-Axes NC Machine Tools Based on the Multi-Body System Theory
Nonlinear Dynamic Modelling of Weld Penetration in Gas Tungsten Arc Welding Process
A Myoelectric Controlled Prosthetic Hand Modelling and its Transmission Mechanism Dynamic Load Based on a Two-Stage Planetary Gear Transmission
Coupling Analysis on Dynamics and Tribology for Cycloid Transmission Used in Robot Joint
Force Transfer Mechanism of the Hinge Joint of Multi-Adjacent Hollow Slab Precast Bridge
Interference Fit Design Assessment and Improvement for the Railway Wagon Wheelset with 30 Ton Axle Weigh
Design Reliability Assessment on the Railway Wagon Axle with 30 Ton Axle Weigh
The Statics and Dynamics Analysis of High-Dynamic Flight Simulator Based on Substructure Method
Strength Analysis of the Seat Structure for Large Passenger Vehicles by Using Finite Element Method
Strength Analysis of the Seat Anchorages for Large Passenger Vehicles Using Finite Element Method
The Weight Reduction Design of the Regenerator CA Nozzle in FCC Unit Using the FEA
Block Shear Behaviors of Angle Two-Bolted Connections with Austenitic Stainless Steel – Experiment and Finite Element Analysis
Comparison of Experimental and Numerical Failure Criterion for Formability Prediction of Automotive Part
Design on the Drag Reduction Surface of an Arc-Shaped Revolution Body with the Phyllotactic Pattern
Design and Fabrication of the Lubricating Dimple of the Headface Sliding Bearing with Phyllotactic Pattern
Heat Resistant Turbine Wheel Development of Automobile
Some Properties of the Pneumatic Artificial Muscle Expressed by the Nonlinear Differential Equation
Finite Element Analysis of Piston under Mechanical Load
The Visualization Manufacturing System Research Based on Three-Dimensional Process Model of Full Information
Research of Automotive Airbag Automatic Folding Device
Study on Watercraft Driving Simulator
Finite Element Analysis and Structure Optimum Design of Lifting Padeye
Effects of Aerodynamic Force on Strength Characteristics of Turbocharger Blades
Strength Analysis of Chassis Structure for Double Deck Bus
Study of Key Technologies of Monitoring in Stage Hydraulic System
Spatial Filtering Effect of Tip Clearance Using Capacitance Displacement Sensor
Thermodynamic Feasibility of Cogeneration Gas/Steam Combined Cycle
Thermal Analysis of Combined Cycle Power Plant with Desalination Unit
Simulation of Solar Energy Storage System
The Velocity Decay Property of Different Shape Fragments for Explosive Anti-Riots Munition
Affection Mode of Temperature on the Lithium-Ion Battery Performance Used in Electric Vehicle
An Assembly Simulation Optimization Method Based on View Transformation
Research on Manufacturing Engineering Change Implementation Planning
Finite Element Analysis of High-Decker Bus Frontal Impact Based on ECE-Regulation No.29
3-D Modeling the Magnetic Field due to Ocean Tidal Flow O1
Load Curve Analysis and Load Errors Modeling of Long Span and Heavy Load Crossbeam
Calculation Methods of the Local Structure Behavior of Unbonded Flexible Pipes
Research of Slider-Crank Massager Noise Fault Diagnosis and Treatment
Chapter 3: Detection, Monitoring and Image Processing Technologies, Information Technologies, Control and MEMS
A Novel Intelligent Network Booting System
Variable Deadband Sampling and T-S Fuzzy PID Co-Design for Optimizing QoS and QoP of Wireless Networked Control Systems
Influence of Clique Potential Parameters on Classification Using Bayesian MRF Model for Remote Sensing Image in Dali Erhai Basin
Software Reliability Demonstration Testing Plan Based on Bayesian Theory
A Novel Virtual Vector Field Method for Image Segmentation Inspired by Physical Electro-Static Force
Obstacles Detecting on Blind Sidewalk System Based on Image Processing Scheme
DC Power Dynamic Management System in Digitalized Transformer Substation
CATIA Based 3D Product Information Definition and Organization
Blind Adaptive Channel Equalization Using Modified CMA
A Method for Multi-Attribute Decision-Making with Complementary Preference Information on Alternatives
The Contour Size Detection of Driver Airbag Based on Image Processing Technology
The External Thread Detection of Liquefied Gas Valve Based on Image Processing Technology
Coefficient Identification of Steam Network Model Based on Genetic Algorithm
The Emergency Rescue and Path Optimization of Dangerous Goods Based ArcGIS
Design and Realization of Smart Home Environmental Monitoring System Based on Wireless Sensor Networks
A New Adaptive UPF Algorithm through Improved Relative Entropy
The Research of CR’s Application for Bluetooth Network
Integration Research of Thermoelectric Enterprise Marketing Management Information System
Data Imputation for Regional Traffic Index Based on GSO-NN
A New Local and Global Model to Iris Recognition
An Efficient Iris Segmentation Method for Non-Ideal Iris Images
Mixed H8/H2 Output Feedback Stability Control for Dual-Motor Independent Drive Electric Vehicle
High Sensitivity Refractive Index Sensor Based on Long Period Fiber Gratings in Line Mach-Zehnder Interferometer
Development of a Hybrid Life Cycle Cost Model for Estimating Product Design Alternatives in Cloud Computing Based Collaborative Design Environment
Amplifier Design on 16-Channel High-Frequency Current Drive
Design of Automatic Detection System for Temperature Sensor Based on LabVIEW
Design of a Multi-Mode Asymmetric Waveform Generator for FAIMS
Analysis of Displacement Monitoring Measurement in Tunnel Construction
Study on Fuzzy Inference Method for Fault Diagnosis Expert System
A Novel Preprocessing Method for Palm Vein
Research on Recognition of Pathological Voice by AD Tree
A Modified MUSIC Algorithm for DOA Estimation
The analysis of 3-Level Charge Pumping in SOHOS Flash Memory
Application Research of rCOS-Based Trusted Requirement Engineering
