Buch, Englisch, 726 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 1700 g
Buch, Englisch, 726 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 1700 g
ISBN: 978-3-03785-955-1
Verlag: Trans Tech Publications
Autoren/Hrsg.
Fachgebiete
Weitere Infos & Material
Preface and Organizing Committee
Chapter 1: Polymer Materials and Composite Materials
Effect of Polymeric Combinations on Mucoadhesive and Swelling Properties of Orabase Gel Formulations
Power Law and Stretched Exponential Responses in Composite Solids
Facile Synthesis and Optical Properties of TiN/Al Composite Powders with Nano/Microstructure by Ball-Milling Method
A Study of Reaction Viscosity Changes in Electronic Packaging with Different Nanoparticle Strengthened Epoxy Matrices
The Effects of Chemical Resistance for Nanocomposite Materials via Nano-Silica Addition into Glass Fiber/Epoxy
Influences of Nano-Silica Addition on Diluent/Epoxy Mechanical Properties
Effects of Nano-Silica Addition on Water Absorption of Glass Fiber/Epoxy Composite
Effects of Nano-Silica Addition and Reactive Diluent Addition on Dynamic Mechanical Properties of Epoxy Nanocomposites
Structural Reorganization in Thin Films of High Molecular Weight Block Copolymer Self-Assembly
The Research of AlN-Mo Nano Composite Ceram
Formation of Thermally Induced Defects in Silica Optical Material
Properties and Application of Alumina Reinforced Aluminum Composite
Preparation and Characterization of Diatomite Supported Cu-Doped TiO2 Photocatalysts
Fabrication of Nano-branched Coaxial Polyaniline / Polyvinylidene Fluoride Fibers via Electrospinning for Strain Sensor
Excellent Electrochemical Performance and Thermal Stability of LiNi0.5Mn1.5O4 Thin-Film Cathode Prepared by Pulsed Laser Deposition
Investigation on Soldering High Volume Fraction SiC Particle Reinforced Aluminum Metal Matrix Composites
The Preparation and Properties of the Conductive and Magnetic Tin-Coated Polyester Fibers for Clothing
Preparation and Characterization of Porous Carbon/Nickle Nanofibers by Electrospinning
Devitrification and Recrystallization of Aqueous Glycerol and PEG-600 Solutions with Nanoparticles
Coupling {001} Facets Dominated Anatase TiO2 Nanosheets with CNTs for Efficient Photocatalyst
Comparison of Ni0.8Cu0.2Ox Anode Material Prepared with Sol-Gel Method and Ni0.8-Cu0.2-Coated YSZ Composite Anode Material Prepared with Polyol Method
Chapter 2: Metals Materials and Building Materials
Thermo-Mechanical Behavior Analysis of Pressure Infiltration Casting Process for Manufacturing Open-Cell Metal Foam
DC Magnetron Sputtering of B2 Phase Feal(111) Single-Crystal-Like Films and Hydrogen Damage Behavior
Investigations on Residual Stress Distribution for 2A02 Aluminum Forgings
Effect of Pile-Up on Nanoindentation Measurements of Polycrystalline Bulk Metals
The Experiment Study on Adherence Capability between New and Old Concrete of Pavement
Corrosion Behaviors and Mechanical Properties of CrN Film
Effect of Process Parameters on Porosity of Intermetallic NbCr2 Porous Materials
Numerical Simulation Study on the Cement-Based Absorbing Material
Underground Engineering Avoid Incision and Reinforced Technology and Engineering Application
Experimental Research on Aluminum Foam Dynamics Performance
Bulk Permanent Magnet with Enhanced Anisotropy Fabricated by Magnetic Annealing from Fe-B-Nd-Nb Bulk Metallic Glass Precursor
Mixed-Mode I/III Fracture Characterization of Aluminum Alloy
The Oxidation Mechanism of FeCrAl Alloy Added with Rare Earth Y from First-Principle Study
Development of Integrated Experiment Program for Marine Concrete Durability
A Study on Chemical Foaming Geopolymer Building Materials
Research on Absorbing Property of Cement-Based Material Blending with Nano-TiO2 and Steel Fibers
Research on Absorbing Property of Three Kinds of Cement-Based Material Blending Compositions
Increasing Tool Life by AlCrTiSiN Film
Study of Oil Displacement Performance of Hydroxyl Sulfobetaine Surfactant
Long Term Monitoring of Performance Characteristics of the Pavement Test Track
Chapter 3: Biochemistry Materials and Engineering
Efficacy Comparison of On-Site Preparation of 5%Lidocaine Niosome Dispersion and Benzocaine/Tetracaine Gel
Tripod-Like ß-NaYF4: Ln3+ (Ln = Yb, Er, Tm, Ho) Nanocrystals with Multicolor Upconversion Luminescence
Culture Conditions of a Mycorrhizal Fungus and its Post-Inoculation Microbial Effect
Studies on Lignocellulose Degradation by Rumen Microorganism
New-Type Biosensor Based on Multiple Total-Internal Reflections in Heterodyne Interferometry
Heat Treated and As-Plated Electroless Duplex Ni-P/Ni-B Coatings: Evaluation of Hardness and Wear Resistance
Development of Novel Bio-Degradable Electrolyte Based on Polylactide (PLA) for Lithium Rechargeable Battery
Improvement of Acid Clay Using Calcium-Rich By-Product Recovered from Petroleum De-Sulfur Operation
Ecotoxicity of Nanomaterials on the Basis of Clay Minerals
Chapter 4: Energy Science and Environmental Engineering
Design and Test of a Lab-Scale Vanadium Redox Flow Battery Cell Considering Electrolyte Feeding Structure for Solar Energy
Solid-State Dye-Sensitized Solar Cells Using Mesoporous TiO2 Films Fabricated with Amphiphilic Rubbery Random Copolymer
Research on Anti-Interference of Measurement-Control Device in Substation Automation System
Stand-Alone Photovoltaic Based on In-Phase Voltage Injection for Electroplating Industry Factory
Performance of Bi-Facial PV Modules in Urban Settlements in Tropical Regions
Thermo-Hydraulic Performance Evaluation of Inclined Vortex Generators
Garbage Incineration and Intelligent Fusion Strategy of Secondary Pollution Control
Parameters Influencing the Utilization of Composts for Energy Production
The Composition of Humic Acids Separated from Compost Prepared from Biologically Degradable Waste
Silicon Nanowires Based Solar Cell Using Native Oxide and Silicon Nitride Bi-Layer Passivation
On Optimal Functioning of the Aeolian Electro-Power Systems
Upon Power Loses due to Current Harmonics in a Fotovoltaic System, Opperating at Maximum Power Point
Dump Load Shedding and Slope Angle of Optimization Design
Water Status and Prospects for Remote Sensing
Housing Development, Energy Consumption and Energy Prices
Noise Source in Automobile and Control Method for Environmental Protection
Numerical Simulation on Flow Field inside the Drainage Valve of the Natural Gas Pipeline
Improved Variety Populus Alba×Populus Bolleana and its Parents Growth Characteristic
Study on the Charging Characteristics of Lithium-Ion Batteries for Electric Vehicles Regenerative Braking
Theoretical Calculation of the Detonation Parameters of Nitropyrazoles Explosives
Chapter 5: Manufacturing Science and Engineering
Effective Use of CA System for Control of Water-Jet Cutting Technology
Calculation of the Size of the Sand Resistance Machine
Simulation of Generated Heat by Friction of Explosion-Proof Elevator Ropes
Numerical Simulation and Analysis of Thermal Energy Generated by Friction on Explosion-Proof Elevator
Control of Hybrid Stepping Motor Drive Using Computational Verb PID Controllers
The Design of the Footrest for the Auto Seat Based on Theergonomics
Discussion the Re-Use Precision Locknut of the Machine Tools Spindle in the Vertical Assembly Characteristics
Friction Characteristics of Clasp Locked Precision Locknuts under Different Conditions
Effects of Parameters on Flutter of a Wing with an External Store
Effect of Tool Shape on Galling Behavior in Plate Shearing
A Combined Physiotherapy Ultrasound and Electrical Shock Device (COMPO) Design
Interactive Body Balance System (IBAS) Design
Structures Analysis and Optimum Design of the Large Stroke Two-Axis Fast Tool Servo
Study of Spindle Current Signals for Tool Breakage Detection in Milling
Interference-Fit Joining of Aluminium Tubes by Electromagnetic Forming
The Discussion of Rotor Guide Channel Length of Vertical Shaft Impact Crushing Test Machine
Research on the Core Method of Lean Construction Management Mode and its Implementation
A Study on the Applicability of Direct Evaporative Cooling Air Conditioner Used in Lanzhou
The Research of the Plane Receiving Array in Offset Parabolic Reflector Antenna with Multi-Beam at Millimeter-Wave Band
Production Capacity Allocation for Multi-Generational Products Based on Decision Tree Method
An Improved Design Method for Automotive Powertrain Rubber Mounts
Computational and Mathematical Modelling during Calculation of Margin of Safety as the Way of Decrease in Expenses of Energy during the Operation of Combined Designs
Development of Temperature Control System of Multi-Function and All-Electric Rheometer
Size Design of Capillary and Barrel of Multi-Function and All-Electric Rheometer
A Convenient Method for Calculating Internal Force of Rod for Tower Crane
Analysis of China PV Application Market Development Support Policy Based on NPV Model
Analysis on Kinematic of Rod on Rotor with Sine Curve Revolving Speed in Twin-Rotor Cylinder-Embedded Piston Engine
Vibration Fatigue Analysis of the Structure under Thermal Loading
Research of a New Theoretical Model of Innovative Design Methodology
A New Approach to Characterize Moisture Management Properties of Diaper
Numerical Simulation of Aerodynamic Performance of Film Cooling on a Flat Plate with Surface Roughness
Analysis on Induced Stress Field by Pore Pressure Change of Sandstone Reservoir
The Theoretical and Experimental Research on Accelerated Life Test of Collapsible Fabric Tank Storage Life Based on Reliability
Analysis on Avoid Incision in Underground Engineering Reinforcement Technique against Cutting Resistance
Applying Support Vector Machines in Rebound Hammer Test
Effect of Blank Shape and Size on the Forming Quality of Thread Shaft Rolling in Cross Wedge Rolling
Chapter 6: Mechatronics and Microelectronics
Design and Realization of Robot Workplaces with Virtual and Augmented Reality Application
Algorithms for Dynamic Hardness Measurements by Scratch Testing in the Submicron and Nanometer Scale
Design of Automatic Scraping System
The Spectral Element Method for the Steklov Eigenvalue Problem
Linear Matrix Inequality and its Application in Control Theory
Study of Fault Arc Protection Based on UV Pulse Method in High Voltage Switchgear
Intelligent Aquaculture Monitoring System Based on Fieldbus
A Survey on Randomized Sampling-Based Path Optimization Methods
Chapter 7: Computer and Internet Application
Three-Dimensinal Structure Modeling of Lishui Depression, East China Sea Basin
A Review on the Bin Packing Capacitated Vehicle Routing Problem
A Novel Model for Multi-Parametric Load Balance in Grid Computing
Research on Piano Music Signal Recognition Based on Short-Time Fourier Analysis
Application of Operator Libraries on Laminate Strength Optimization of Composites
Virtual Learning Technology and Materials in Malaysian Higher Education
