Selected, peer reviewed papers from the 16th International Symposium on Advances in Abrasive Technology (ISAAT 2013), in conjunction with the 17th Chinese Conference of Abrasive Technology (CCAT 2013), September 23-26, 2013, Hangzhou, China
Buch, Englisch, 720 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 1400 g
ISBN: 978-3-03785-825-7
Verlag: Trans Tech Publications
Autoren/Hrsg.
Fachgebiete
Weitere Infos & Material
Preface, Sponsors and Committee
Chapter 1: Abrasive Jet Machining
Optimization of Hybrid Laser-Waterjet Micromachining of Silicon
A Visualization Study of the Radial-Mode Abrasive Waterjet Turning Process for Alumina Ceramics
An Experimental Research on Abrasive Water Jet Polishing of the Hard Brittle Ceramics
Study on the Effect of Standoff Distance on Processing Performance of Alumina Ceramics in Two Modes of Abrasive Waterjet Turning Patterns
An Experimental Study on Radial-Mode Abrasive Waterjet Turning of Alumina Ceramics
Kerf Profile Characteristics in Abrasive Air Jet Micromachining
A Study on Erosion Performance of Monocrystalline Silicon in Ultrasonic Vibration-Assisted Abrasive Water Jet Machining
Impact Erosion of Quartz Crystals by Micro-Particles in Abrasive Waterjet Micro-Machining
Chapter 2: Abrasive Machining
Optimization Design for Gun-Receiver Materials Belt Grinding Based on Orthogonal Experimental Method and Grey Relational Analysis
Research on Cutter-Contact Point Data Calculation of Robotic Abrasive Belt Polishing for Gun-Receiver Surface
Research on the Technology of Nc Abrasive Belt Grinding for the Leading and Trailing Edges of Aero-Engine Blades
Feasibility Study on Grinding of Titanium Alloys with Electroplated CBN Wheels
Research of Micro-Abrasive Suspension Jet Erosion Morphology and Material Removal Mechanism
Machining Characteristics of Multilayered Thin Film Solar Panels in Diamond Wire Sawing and Grinding
Influence of a Grinding Atmosphere in the Combination Grinding of Steel and WC with a Diamond Wheel
Experimental Investigation of Material Removal Mechanism in Grinding of Alumina by Single Grain Scratch Test
Compensation and Experiment Research of Machining Error for Optical Aspheric Precision Grinding
Dynamics Modeling of Cavitation Bubble in the Grinding Area of Power Ultrasonic Honing
Experimental Studies on Forces and Specific Energy in High Speed Grinding of Titanium Alloy Ti6Al4V
Study on the Effect of Coarse Grinding Area Slope Angle on Surface Quality in Point Grinding
Grinding Force Model for Low-Speed Grinding Based on Impact Principle
Ultraprecision Lapping for the Zirconia Ceramic Plane
Experimental Study on the Ultra-Precision Polishing for the Quartz Substrates
High-Accuracy Calibration of the Wheel Spindle Tilt Angle for Grinding Hydrostatic Seal Rings Used in Reactor Coolant Pumps
Chapter 3: Advanced Cutting Technology
Experimental Study on the Thread Turning Performance of Two TiAlN Coated Thread Inserts with Different Features
Experimental Investigation on Drilling Force and Hole Quality when Drilling of T800S/250F CFRP Laminate
FEM Analyzing Effect of Tool Body Materials on Security Reliability for Face-Milling Cutter
Effects of Cutting Conditions on the Machinability of Stainless Steel Formed by Laser Cladding
Microstructure and Mechanical Properties of Al2O3-TaCw Ceramic Cutting Tool Materials
An Indicative End-Milling Condition Decision Support System Using Data-Mining for Difficult-to-Cut Materials Based on Comparison with Irregular Pitch and Lead End-Mill and General Purpose End-Mill
Cutting Edge Preparation of PCBN Inserts
Comparison of Material Removal Characteristics in Single and Multiple Cutting Edge Scratches
Effect of Fiber Directions on the Surface Quality of Milling C/SiC Composites
Numerical Investigation on Effect of Rounded Cutting Edge Radius in Milling of Ultra-High-Strength Steel 30Cr3SiNiMoVA
Experimental Investigation on the Cutting Mechanism of Oxygen Free Copper in Cutting Speeds Ranging from 1 m/s to 210 m/s
Experimental Study on Fractal Laws of Cutting Force for Machining Irregular Surface of Granite
Chapter 4: Brittle Material Machining
Experimental Investigations of Grinding Forces in Elliptical Ultrasonic Assisted Grinding (EUAG) of Monocrystal Sapphire
Study on Numerical Simulation and Experimental of Cutting Force in Turning Machinable Glasses Ceramics
Grinding Force and Surface Roughness in Ultrasonic Assisted Grinding of SiC Ceramics with Diamond Grinding Wheel
Development of High-Efficiency and Crack-Free Grinding Process for Chamfering of LCD Glass Edge
Predicted Model of Cutting Force for Single Diamond Fast Milling Hard-Brittle Materials
Study on Thermal Influence of Grinding Process on LiTaO3
Chapter 5: CMP and Silicon Wafer Processing
Study on Chemical Mechanical Polishing Parameters of 6H-SiC Crystal Substrate Based on Diamond Abrasive
Optimization of Process Parameters Based on Multi-Process and Multi-Evaluation Index for Function Ceramics in CMP
Investigation of Surface Roughness for Grinding Silicon Wafer of the Micro Pellet Diamond Tool
Investigation of Dressing Characteristics of Single Crystal Diamond in CMP
Study of Cluster Magnetorheological-Chemical Mechanical Polishing Technology for the Atomic Scale Ultra-Smooth Surface Planarization of SiC
Chapter 6: Coolants and Cooling
Development of an Innovative Water Machining System Employing the Electric Rust Preventive Method - Precise Evaluation of Purity of the Refined Water with a Laser Turbidity Meter
A Model of the Fluid Convective Cooling in Grinding Process
Chapter 7: Design, Fabrication and Analysis of Devices for the Applications of Abrasive Technologies
Development of Non-Destructive Inspection System for Grinding Burn - An Application of the Grinding Burn Detecting Technique to Evaluate Residual Stress
Chapter 8: EDM, Ultrasonic Machining, and Laser Machining
Research on the Ultrasonic Assisted WEDM of Ti-6Al-4V
Study on Ultrasonic Generator for Ultrasonically Assisted Machining
Surface Textures Fabrication on Zirconia Ceramics by 3D Ultrasonic Vibration Assisted Slant Feed Grinding
Effect of Ultrasonic Vibration Parameters on Machining Performance Based on Tool-Workpiece Contact Ratio
Surface Quality of Textured Surface on Cylindrical Inner Surface Using Whirling Electrical Discharge Texturing
Fundamental Machining Characteristics of Ultrasonic Assisted Turning of Titanium Alloy Ti-6Al-4V
Effectiveness of Ultrasonic Vibration on Press Forming
A Study on Ultrasonic Assisted Grinding of Nickel-Based Superalloys
Effect of Ultrasonic EDM on Machinability of Coarse PCD
Micro-Grooving of Glass Using Small-Diameter Diamond Grindstone with Ultrasonic Vibration
A Study on Grinding Tungsten Carbide with Ultrasonic Assisted
Chapter 9: Finishing, Lapping and Polishing
Research on Ultra Precision Mirror Machining Technology for Aluminum Alloy Mobile Phone Shell
Research on Process Parameters Influencing on Cutting Force in Abrasive Flow Machining (AFM)
Effects of Magnetic Fluid on Machining Characteristics in Magnetic Field Assisted Polishing Process
Effects of Permanent Magnet Excitation on Material Removal Rate in Area Taking Magnetorhelogical Finishing
Research on Grain Impacting Load in Abrasive Flow Machining
Study of Process Characteristics of Abrasive Flow Machining (AFM) for Ti-6Al-4V and Validation with Process Model
Study on the Characteristics of New Abrasive Medium for Abrasive Flow Machining
Experimental Study on Micro-Deliquescence Ultra-Precision Polishing with Fine Water Mist for KDP Crystal
Research on Distribution of Magnetic Particles Based on Magnetic Field Control Grinding Wheel
Experimental Research on Rolling Bearing Raceway Finishing
A Study on the Analysis of Influential Factors for 300mm Wafer Final Polishing
Study on Dual-Plane Ball Polishing Method for Finishing Ceramics Ball
Polishing Characteristics of a Low Frequency Vibration Assisted Polishing Method
Polishing Technology and Phenomena of the Inner/Outer Surfaces of Small Cup-Type Nickel Tube-Study of Ultraviolet-Ray Aided Machining
Friction Force Analysis on Diaomond Lapping of Sapphire Wafers
Study on Impinging Stream Flow Channel in Abrasive Flow Polishing Complex Cavity of Precision Mold
Proposal of Finishing Method of MLA Mold Applied Sphere Indentation
Chapter 10: Glass Molding and Related Topics
Experiment on Glass Microgroove Molding by Using Polycrystalline Nickel Phosphorus Mold
Chapter 11: Grinding Wheel and Abrasive Grain Technologies
Experimental Study on a New Combination Processing Technology of Polycrystalline Diamond
CVD Micron Diamond Powders
Study on Radial Deformation of CBN Grinding Wheel Considering Centrifugal Force and Grinding Heat
Progress of Researches on the Surface Topography Detection Techniques for Grinding Wheel
Creep Feed Grinding of Ni-Based Superalloy with Micro-Crystalline Ceramic Alumina Wheels
Grinding Characteristics of Porous Composite-Bonded CBN Wheels
Effect of Contact Stiffness of Grinding Wheel on Ground Surface Roughness and Residual Stock Removal of Workpiece
Analysis on Wear of Self-Sharpening Fine Super-Hard Abrasive Tool
Heat Pipe Grinding Wheel in Grinding Titanium Alloy Ti-6Al-4V
Chapter 12: In-Process Measurement and Monitoring, Metrology
Development of CMM Auxiliary Equipment for Tiny Hole Measuring
A Thin Silicon Wafer Thickness Measurement System by Optical Reflectmetry Scheme Using Fourier Transform Near-Infrared Spectrometer
Review on Multi-Point Method for Roundness Error Separation
Development of a Measuring Equipment for Silicon Wafer Warp
Chapter 13: Machine Tools and Systems, Tooling Processing
Research on Iso-Scallop Method for NC Grinding of the Special Rotating Workpiece
Mathematical Modeling and Parametric Design of Taper End Mills
Adaptability Comprehensive Evaluation of Auto Assembly Machine Product Platform for Small Shaft and Sleeve Subassemblies
Development of Electronic Impact Hammer and its Application to Face Milling Cutter Modal Analysis
Research on Hole-Making Tools for CFRP
Experimental Investigation on Grinding Performance of Microcrystalline Alumina Abrasive Grinding Wheel for Superalloys
Study on the Restraint Method of Thermal Deformation in the Machine Tools
Grinding System Reducing the Influence of Thermal Deformation of Workpiece in Cylindrical Grinding
Chapter 14: Micro/Nano-Machining
Experiment Research on Grinding Temperature of Micro-Grinding H62
Finite Element Simulation of Minimum Uncut Chip Thickness in Micro Mill-Grinding Ti6Al4V Based on Single-Edge Single-Grit Model
The Dynamic Analysis of Micro-Scale Edge in the Process of Micromilling
Fabrication of Surface Microtexture by Vibration Assisted Cutting
Bending of Drill and Radial Forces in Micro Drilling
An Approach to Improve Machined Surface Finish in Micro Milling
Chapter 15: Surface Integrity and Materials Characterization
Experimental Research on Surface Residual Stress of Quenched GCr15 Steel in Ultrasonic Aided Turning
Effect of Low-Frequency Pulsed Magnetic Treatment on Micro-Hardness of High Speed Steel
Indentation Crack Initiation and Ductile to Brittle Transition Behavior of Fused Silica
Research on Subsurface Damage Layer Detection during Substrate Processing
Surface Integrity - an Inherent Load Sensor
Surface Layer Damage of Silicon Wafers Sliced by Wire Saw Process
Study on the Subsurface Damages of Glass Fiber Reinforced Composites
A Modified Surface on Titanium Alloy by Micro-Blasting Process
Crack Filling of Cover Glasses by Sol-Gel Coatings
A Study of Mechanical Properties and Material Removal of Polycrystalline Tungsten via Nanoindentation and Nanoscratch
Chapter 16: Tribology in Manufacturing
Friction Evolution in Running-In of Sliding Wear of Cast Iron Processed in Gleeble
Frictional and Wear Behavior of Micro-Crystalline and Nano-Crystalline Diamond Films
Dry Sliding Wear of As-Cast and Thermomechanically Processed Low Chromium White Cast Iron
Chapter 17: Truing, Dressing and ELID
Study of Grinding Force for Internal Cylinder of Ultrasonic ELID Composite Grinding
Research on ELID Grinding Performance of GCr15 Steel
Experimental Study on Dry Electrical Contact Discharge (ECD) Dressing Parameters of Coarse Diamond Grinding Wheel
Visualization of 3D Topography of Grinding Wheel Surface Dressed by Rotary Diamond Dresser
