Buch, Englisch, 690 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 1400 g
ISBN: 978-3-03785-467-9
Verlag: Trans Tech Publications
Autoren/Hrsg.
Fachgebiete
Weitere Infos & Material
Preface, Sponsors and Organizing Committee
Chapter 1: Grinding and Grinding Wheels
Ultrafine Surface Finishing of Fused Silica Glass Using MCF (Magnetic Compound Fluid) Wheel
Study on the High-Efficiency Smoothness Grinding of Soft Magnetic Powder Cores
Grinding Performance Using Alkaline Electrolyzed and High-Frequency Reduced Water
Study on Grinding Processing of Sapphire Wafer
Effect of the Grain Depth of Cut on Cross Sectional Profile - Theoretical Analysis of Ground Surface Roughness
Development of a Vitrified Bonded Superabrasive Wheel with Electrical Conductivity and its Application
Fundamental Study on Setting of Diamond Abrasive Grains Using Electrostatic Force for Single-Layered Metal Bond Wheel
Porous Composite-Bonded CBN Grinding Wheel with Alumina Bubbles
Estimation of the Grinding Time by Means of the Grinding Process Model
Study on the Simulation of Grinding Burn
Experimental Research on the Abrasive Belt Grinding Titanium Alloy Blade of Aviation Engine
Testing of a CNC Control Abrasive Belt Grinding Machine Based on Ultrasonic Thick Measure for Nuclear Zirconium Alloy
Research on the Key Technology of NC Abrasive Belt Grinding for the Leading and Trailing Edges of Aeroengine Blades
Optimal Design of the Grinding Parameter on Zr-4 Cladding Tubes Abrasive Belt Grinding Based on BP and GA
Experimental Investigation on Grinding Surface Condition of 9Mn2V under Different Tempering Processes
Grinding Force in Creep Feed Grinding of Titanium Alloy with Monolayer Brazed CBN Wheels
Accurate Extraction of Normal Residual Error for Compensation Grinding
Grinding Performance Evaluation of the Developed Chemo-Mechanical Grinding (CMG) Tools for Sapphire Substrate
A Grinding Protocol for the Fabrication of Micro/Meso Aspheric Moulds for Optic Applications
Industrial Application of the MCG (Minimum Coolant Grinding) Technology
The Characteristics of High-Speed Cylindrical Grinding of Silicon Carbide and its Influence on the Surface Layer
An Experimental Investigation of Ultrasonic Assisted Grinding in DOE Approach
Design of Ultrasonic Horn for Grinding Using Finite Element Method
Experimental Investigation on Ultrasonic Assisted Grinding of High Volume Fraction SiC Particles Reinforced Al Matrix Composites
Effects of Ultrasonic Frequencies on Grinding Force of Nano-Composite Ceramics Based on Nonlocal Theory
Experimental Research on Surface Roughness of Ultrasonic Assisted Grinding in Face Grinding Process
Experimental Research on Dry Grinding of Titanium Alloy with Graphite Coated Brazed cBN Mounted Wheel
Research on Functional Surface Grinding of Medical Titanium Plate
Thermal Characteristics Analysis of Liquid Hybrid Bearing on Ultra-High Speed Grinding
Three Dimensional Analysis of a Grinding Wheel Surface with Image Processing
Genetic Programming for Grinding Surface Roughness Modelling
Research Progress of On-Line Measurement and Compensation Technology about Grinding Wheel Wear
Influence of the Metallurgical Transformation Induced by Grinding on the Residual Stresses Computation
Chapter 2: Truing and Dressing of Grinding Wheels
Performance of Newly Developed Single-Point Diamond Dresser in Terms of Cutting-Point Rake Angle
Thermo-Chemical Dressing of Coarse Grained Diamond Grinding Wheels
T-Dress, A Novel Approach in Dressing and Structuring of Grinding Wheels
Visualization of Grinding Wheel Surface Topography for Multiple Passes of Rotary Diamond Dresser
Chapter 3: Finishing, Lapping and Polishing
Preliminary Studies for Precision Polishing of Micro Structured Mold by Using Three-Dimensional Low Frequency Vibration Utilizing Piezoelectric Actuator Incorporated with Mechanical Amplitude Magnified Mechanism
Influence of Lapping Parameters on 6H-SiC Crystal Substrate (0001) C Surface Based on Diamond Particle
Influence of Polishing and Pressing Force on the Material Removal Rate in Fixed Abrasive Polishing with Compact Robot
Surface Roughness as a Function of Work Done by Tangential Force in Magneto-Rheological Finishing
Ultrasonic Vibration Assisted Mechanical Chemical Polishing (MCP) of Silicon Carbide
The Key Technologies and Advances of Ultra-Precision Single-Plane Polishing and Lapping Devices
Parameters Optimization on the Lapping Process with Porous Self-Generation Superabrasive Tool by Applying Taguchi Method
Experimental Study on Polishing Properties of Silicone Oil Based Magnetic Compound Fluid
Vibratory Finishing of Immobilized Cylinders
A Framework for the Analysis of Mass Finishing Processes
Simulation of 1D Abrasive Vibratory Finishing Process
A Study on the Characteristics of a Wafer Final Polishing Process at Various Machining and Temperature Variation
Effect of Fabrication Conditions on Ultra-Fine Abrasive Polishing Pad
A New Automatic Backlash Adjustment Method for Lapping of Spiral Bevel Gear
Kinematics Simulation of Eccentric Dual Rotated-Plates Lapping for Bearing Balls
Research on the Workpiece Kinematics in Face Lapping with Friction Drive
Slurry Flow Visualisation of Chemical Mechanical Polishing Based on a Computational Fluid Dynamics Model
Simulation of CMP Process Based on Mixed Elastohydrodynamic Lubrication Model with Layered Elastic Theory
Chapter 4: Abrasive Jet Machining
An Experimental Study of the Abrasive Water Jet Micro-Machining Process for Quartz Crystals
A 3D Simulation on Fluid Field at the Impact Zone of Abrasive Water Jet under Different Impact Angles
The Effect of Abrasive Water Jet Process Variables on Surface and Subsurface Condition of Inconel 718
Chapter 5: Advances in Machining Technologies
Effect of Ground Surface Roughness of Ball End Mill on Cutting Characteristics
Press Cutting Characteristics of Plastic Pipe by Using Knife Edge Tool
Effect of MnS on the Cutting Mechanism of Powder Metallurgy Steel in Cutting Speeds Ranging from 1 m/s to 150 m/s
A Study of Deep-Hole Machining of Stainless Steel with Small-Diameter Drill
Finish Cutting of Carbide Mold with Thermally Affected Layer by Diamond Tool
The Effects of Resharpening Accuracy on Drill Failure and Hole Straightness in High Aspect Ratio Gundrilling of Inconel-718
Effects of Ultrasonic Vibrations Given to an Electrode on the EDM Performance in Processing PCD
Surface Finishing of Electrically Conductive Diamond Tools by Electrolytic Machining
Proposal of Purification Method of Grinding Coolant by Dissolution of Micro-Bubbles
Filter-Less Purification of a Water-Soluble Coolant by Using PGA Based Flocculants and Microbubbles
Slicing Brittle Material with Active Braze Coating Diamond Wire
Improving Tool Wear Resistance in Steel Cutting by Textured Surface and its Mechanism
Micro-Structuring on Cylindrical Inner Surface Using Whirling Electrical Discharge Texturing
Study on the Combined Machining Technology of Sawing and Grinding for Drilling Aramid/Epoxy Composites
Investigation of Micro-Drilling for Printed Circuit Boards Containing High-Hardness Fillers
Modeling the Property Variation of Diamond Composite and its Impact on the Reliability of Cutting Tools
Cutting Forces and Tool Wear in Dry Milling of Ti6Al4V
Development of Al2O3/TiCN Ceramic Composite Cutting Tool and Research on its Milling Performance
Ball-End Milling of Cr12MoV Die Steel Using Ceramic Tool and Cements Carbide Tool
An End-Milling Condition Decision Support System Using Data-Mining for Difficult-to-Cut Materials
Research on the Drilling Temperature Field Model of the Unidirectional Carbon Fiber Epoxy Composites
Chip Formation Characteristics in High-Speed Machining of Hardened AISI1045 Steel
Mechanical Behavior of Single Crystal Copper for Different Shearing Directions
Machinability Study on Hard Milling of Ultra-High Strength Steel 30Cr3SiNiMoVA
Review of Microelectrode Fabrication
Surface Quality Improvement in Meso-Scale Milling with Spindle Axial Directional Ultrasonic Vibration Assistance
Chapter 6: Micro/Nano-Fabrication
Basic Study on Micro V-Groove Cutting of Tungsten Carbide Using Diamond Tools
Study on Fine Groove Milling of Microchannel Dies – Tool Bending in Milling of Micro-Grooves
Effect of Different Dielectric Fluids on Micro EDM of Low Conductivity Ceramic Material RB-SiC
A Processing Technical Analysis for the Characteristics of Forces and Surface Roughness in Micro-Scale Milling
Experimental Study on Cutting Performance in Micro-Grinding Hard Brittle Materials
Atomic-Scale Grooving on Copper: End-Milling vs. Peripheral-Milling
Micro Milling for Polymer Materials Used in Prototyping of Microfluidic Chip Application
An Experimental Study of the Effect of Cutting Parameters on Micro Milling Process
Mechanical Properties and Deformation of LiTaO3 Single Crystals Characterised by Nanoindentation and Nanoscratch
Determination of the Minimum Depth of Cut in Nanometric Machining Using Molecular Dynamics Simulation
A Non-Dimensional Analysis of Tool Edge Radius Effect on the Mechanics of Micromachining
Influence of Centrifugal Force on Characteristics of Turbine Shaft for Micro-Spindle for Micro-Cutting
Effect of Machining of Small Tools by Means of Focused Ion Beam
Chapter 7: Other Novel Technologies and Advanced Studies
Application of Cavitation Aided Abrasive Machining to Manufacture of Micro Air Vents on Injection Molds
Static Properties Research of Grinding Dynamometer for Wafer Grinder
Development of Ultra-Precision Grinder for 300mm Wafers
Deposition and Tribological Properties of CVD Diamond/Diamond-Like Carbon Composite Films
Thermal Analysis of Multi-Pass Laser Irradiation on Fused Silica
Study on Friction Coefficient between Carbon/Epoxy Composites and a Monocrystalline Diamond under Different Temperatures
Simulation of Temperature Field Induced in Localized Ultra-High Frequency Induction Brazing of Diamond Tools
Study of Acoustic System Characteristics of Ultrasonic Machining Based on Similarity Principle
Thermal-Mechanical Analysis of Hybrid Spindle System Based on FEM
Study on Microstructure and Friction of Bimetal 1.5Cr4.8Ni with Cast Iron and Low Carbon Steel
Research on Digital Filters for Si Wafer Surface Profile Measurement - Design of Filters by Total Variation
Application of Automatic Ultrasonic Wall Thickness Measurement System in Nuclear Fuel Encrust Tube Billet Wall Abrasive Grinding
