Sonstiges, Englisch, Band Volume 345, 620 Seiten, Format (B × H): 125 mm x 142 mm, Gewicht: 200 g
Sonstiges, Englisch, Band Volume 345, 620 Seiten, Format (B × H): 125 mm x 142 mm, Gewicht: 200 g
Reihe: Applied Mechanics and Materials
ISBN: 978-3-03795-512-3
Verlag: Trans Tech Publications
Volume is indexed by Thomson Reuters CPCI-S (WoS).
The 130 papers are grouped as follows:
Chapter 1: Mechanical Engineering and Mechanics, Control Technologies in Manufacture and Industry;
Chapter 2: Material Engineering and Processing, Applied Mechanics and Theoretical Computer Methods in Materials;
Chapter 3: Industry Technologies and Application;
Chapter 4: Manufacturing Engineering and Manufacture Automation.
Autoren/Hrsg.
Fachgebiete
Weitere Infos & Material
Study on Mechanical Bearing Capacity with Tabu Search Algorithm for Multi-Vehicle and Multi-Cargo Loading ProblemStudy on Aircraft Mechanics with Accessibility Appraisement of Aviation Equipment Based on Correlation Analysis MethodStudy of Wirebonding Loop Formation and Influencing Factors Based on Mechanical MechanicsResearch and Development of Clean-Energy VehiclesStudy on Mechanical Properties with Effect of Super Capacitor in Energy Feedback of Electric Vehicle BatteryResearch on Mechanical Engineering with Innovative Design of Gantry PlanerResearch on Electric Vehicles with Design of Battery Test System Based on LabVIEWThe Implement of CANopen in Motion Control of Electric VehicleAnti-Surge Control of the Gas Booster in the Thermal Power Plant with Gas-Fired BoilerThe Design and Construction of Air Intake System of a Gasoline-Natural Gas Dual Fuel EngineThe Simulation Research on Air Drag Reduction of Tail Dome on VansThe Design of the Dual Power Mechanical Simple Garage Lifting PlatformAccurate Calculation about Euler Critical Force of Multistep Telescopic Cylinder with Two Different Kinds Support ConditionsShock Test and Acceleration Analysis Methods of Marine Diesel Engines to Underwater ExplosionsThe Steady State Precision Control of DC Servo Motor Based on State Space Adaptive Pole AssignmentCompressing Equipment Control Method of Horizontal Preloading Domestic Waste Disposal Transfer Station and its ImplementationResearch on Servo Valve-Controlled Motor Velocity Control System Based on Fuzzy ControlThe Digging Shovel of Corn Stubble Shop Machine Design and the Performance of Drag Reduction TestStudy on the Correspondence of Hamiltonian Flows and Functions of Brake Hamiltonian System Based on Mechanical MechanicsSimulation of Three-Phase Motor Rotor Flux Oriented Control System Based on SVPWMInvestigation on Vibro-Acoustic Characteristics from Submerged Cylindrical Shell with Double Damping LayersSimulation Research on the Basic Platform's Automatic Leveling System Based on SimHydraulicsOptimal Control for Three-Axle Vehicle's All-Wheel SteeringDevelopment and Application of Portable Mining Vibration RecorderResearch on Mechanical Faults with Application of Three Order Cumulants' Coupling Features in Fault DiagnosisResearch on Mechanical Faults with Application of 1(1/2) Dimensional Spectrual Coupling Features in Fault DiagnosisResearch-Based Single Chip Microcomputer Controlling of Throttle in 09-32 Tamping MachineModal Analysis on Tooth Ring Plate of Three-Ring Gear ReducerResearch on Mechanical Design with Design and Implement of High-Frequency Excitation Signal Source in Eddy Current TestingDesign Method for Folding Boom Structure of Elevating Platform Rescue Fire TruckDynamics Analysis of Milling Machine SpindleApplication of Microscale Gas Leak Detection Technology on Small Pressure VesselThe System Design of Granular Bulk Materials Continuous Conveyor Weighing MeasurementSearch and Doubts of the Calculation Equation of Efficiency Transmission of CLS-II Type Efficiency Transmission Gear Experiment SetExperiment and Research for Calculation of Efficiency Transmission of CHT-100 Type Circulating Power of the Efficiency Transmission Gear Experiment SetAdsorption of Methylene Blue onto Char from Pyrolysis of Municipal Solid WasteMolecular Dynamics Simulations of Sliding Friction of Rigid Sphere with Single Crystal Copper SurfaceSynthesis and Application of Carbon-Based NanocompositesCatalytic Wet Air Oxidation of Phenol over Oxidized Activated CarbonSurface Chemical Modification and Characterization of Nano Fe2O3Research on the Concrete Performance in the Marine EnvironmentSynthesis, Characterization, and Photoluminescence of a Novel Eu-Containing Polymer Precursor: {Tris(acetylacetonate)5-acrylamido-1,10-phenanthroline}Europium(III)Array of Fe3O4 Nanoparticles in PS-b-P2VP thin FilmsSimulation of Graded Band-Gap PIN nc-Si Thin-Film Solar CellsPreparation of Mesoporous Magnetic TiO2/CoFe2O4 Photocatalysts Using Ionic Liquid as Template AgentEffect of the Pore Fractal Dimensions on Absorption Ability in Superabsorbent FibersMicrostructural Evolution and hardening of Subsurface of Mg-3Al-1Zn Alloy during Dry Sliding WearExperimental Investigation of Low Velocity Impact and Residual Compressive Properties of Composite Laminates Based on AEResearch on Composite Powder and Magnet Properties of Bonded NdFeB Magnets Prepared by Press MoldingPreparation Technology and Mechanical Properties of Fe-C Composites Fabricated by Plasma Activated SinteringExperimental Study of New Rubber Plastication MethodTheory Research on Full Metal Single Screw PumpAnalysis of Combined Support Technology with U-Shaped Steel Bracket and Anchor BoltExperimental Investigation on Refill Friction Stir Spot Welding Process of Aluminum AlloysMultidispersion Soot Interference Mechanism on SO2 Concentration Using NDIRMonodispersion Soot Particle Interference on NO2 Concentration Measurement Accuracy Using NDIRInterference Mechanism on NO2 Concentration by the Multidispersion Soot Using NDIRResearch on Residual Stress of Engineering Ceramic Grinding SurfaceThe Material Discontinuous Zone Influence on the Behavior of Crack Propagation in the Matrix MaterialConsistent Mode Mixity for the Interface Crack of the Bimaterial Disc under Diametric Compression LoadingApplication of ANN Back-Propagation for Fracture Design Parameters of Middle Carbon Steel in Extra-Low Cycle Bend Torsion LoadingStudy on Electromagnetic Shielding Material Performance Based on the Status of the Test MethodModeling of Engineering Ceramics Grinding Surface Residual StressOptimum Design of Curvilinear Stiffened Panels with Stiffening BeamsExperimental Investigation of Tensile Damage Mechanisms on 3-D Braided Composites with AEResearch Progress in Mechanics of Hollow Section RC Bridge Piers Subjected to Seismic Dynamic LoadTheoretical Study on Reactivity of Fe-Based Oxygen Carrier with CH4 during Chemical Looping CombustionStructure Analysis of the Large Bridge-Craft Using Finite Element Method Based on Properties of Engineering Materials and Mechanical MechanicsDeformation Behavior and Dynamic Stress Response of High Railway Embankment under Cyclic LoadNumerical Simulation of Residual Stress Field Induced by Water-Jet Cavitation PeeningStability Analysis for Horizontal Boom with Double Pulling Rods under Non-Conservative ForcesElastic-Plastic Deformation of Milling Thin Wall PartNumerical Computation Studies and Hydrodynamic Analysis on the Cutting-Carrying and Lifting Capacity of Spiral Centralizer in Gas DrillingResearch on Fluid Mechanics with the Finite Analytic/Grid Method for Two-Phase Turbulence Based on PDF TheoryFluid Dynamic Simulation of a Wall-Jet-Flow Loaded with Solid Particles Using the Finite Analytic/Grid Method of PDF ModelStatic Instability of a Restrained Cantilever Column with a Tip Mass Subjected to a Subtangential Follower ForceFlow-Induced Noise Radiation from the Rotational Bodies Based on Fluid Mechanics Using Hybrid Immersed Boundary Lattice-Boltzmann/FW-H MethodNumerical Simulation of Filling Process in Casting Based on a Hybrid Lattice Boltzmann and Particle Level Set ModelStudy on Electronic Industry with an Application of Rectilinear Embedding in VLSI PlacementResearch on Photovoltaic Industry with the MPPT Algorithm in PV SystemResearch and Design of Temperature Monitoring System in Industry Applications Based on PLCGARCHSK Based Risk Assessment in Electric Power IndustrySimulation Analysis on Industrial Wastewater Adjust Pool Stench in Collecting Hood with Properties of Environmental MaterialsResearch on Petrochemical Industry with Analysis of Floating Roof Tanks under the Planar Inclined FoundationStudy on the Sustainable Development Evaluation of Logistics Enterprise for Industry Manufacturing Based on Data Envelopment AnalysisStudy on the Model of Quantitative Evaluation of Circular Economy Development for Industry Manufacturing Based on WIOAStudy on Formative Industry Design with Trace to Source of Formative ThinkingStudy on Formative Industry Design with the Impact of Gestalt Psychology on Modeling CognitiveIntelligence Based Control Strategy of Forming Process for Plastic & Rubber ProductsResearch on the Measuring of the Order of Eco-Industrial Chains for Recycling Waste Material Based on the Theory of Dissipative StructureResearch on Mechanical Operation with Sequencing Optimization of Arrival Aircraft in Terminal AreaOnline Scheduling with Incompatible Job Families on Batch Processing Machine(s)Mechanical and Electrical Integration of Workpiece Transfer SystemResearch on Mechanical Design with Beidou GPS Navigation Antenna Design TerminalResearch on Development Potential of the New Energy Industry Based on Fuzzy Comprehensive EvaluationThe Focusing Mechanism Design for Laser Anti-Counterfeit Platform in Production Manufacturing EngineeringThe Modal Analysis of Focusing Mechanism for Laser Anti-Counterfeit Platform in Production Manufacturing EngineeringResearch on Food Processing Engineering with an Inventory Model for Foodstuffs with Service LevelA Hybrid Ant Colony Optimization Algorithm for Permutation Flow-Shop Scheduling in Manufacturing Systems and Industrial ProcessBrief Analysis of Floor Grouting Method in Soft Rock Roadway Based on Engineering Materials and Engineering MechanicsNew Technology and Mechanism Study of the Bearing Enhancement of Broken Rock Zone in Underground Rock RoadwaySimulation and Analysis for the Rocket Gas Flow Field Based on Mechanical Mechanics and Mechanical PropertiesStudy on Machinery and Electronics Engineering with Analysis and Modeling on Electromagnetic Environment Based on Radio Seeker Penetrating ProcessExperimental Study of Resonant Frequency Tunable Piezoelectric Energy HarvesterStudy on Bicycle Manufacturing Engineering with the Quality Detection Device for the Carbon Fiber Sports BicycleStudy on Manufacturing Engineering with Supply Chain Profit Model of Fast Moving Consumer Goods Based on TOC Operation ModeModeling and Analysis of the Discrete Manufacturing Product Quality with Information Formation Process for TraceabilityManufacturing Process Design Based on Mental and Physical Workload AnalysisMulti-Objective Optimization in Manufacturing Engineering for Slender Pen Rod Injection Molding Quality Based on Grey CorrelationDigital Research on Oblique Cutting Parameters of Round BroachMechanical Automation of Rice Transplanting and Key Agronomic TechniquesThe Stress Distribution Analysis of Spiral-Wound Heat ExchangerA Model of Weight Absolute Grey Correlation Degree for the Transformer Bushing State AssessmentResearch of Mechanical System on Rotary Steering Drilling ToolReliability Research on Measurement System for Downhole Storage Pressure GaugeInfluence of Three-Dimensional Stability Lobes on the Cutter DesignStatic Analysis on the Measurement System of an Electronic Belt ScaleDesign of Two-Welding Torch Automatic Welding MachineThe Analysis of the Automatic Steel Drum TilterIdentification of Toolholder-Spindle Joint Based on Receptance Coupling Substructure AnalysisThe Semi-Automatic Drilling Machine for Flange ProcessingResearch on Decision Support System of Relay Protection Equipment Status Evaluation Based on Mechanical OverhaulThe Finite Analysis and Optimization of Gantry Beam on Automatic WelderFinite Element Analysis of the Frame of Straightening Machine with Twelve Rolls for TubesOptimization Design Method for Body Frame of Vehicular Glass Edge Grinding Machine Based on Goal-Driven OptimizationDynamic Analysis of Scratch System of Grating Ruling MachineExperimental Investigation on a Heat Recovery Device Installed on Cement Rotary KilnResearch on Removal Equipment for Industrial Dust Emissions with the Finite Element Method for the Manner of Filter Board and Filter Bag LayoutAnalysis on Gas Flow Field in Bell-Type Annealing Furnace by Using FLUENTOptimization of Injection Molding Process Parameters with Material Properties Based on GA and BP
