Materials and Processing Technology II

Erscheinungsjahr 2018
ISBN: 978-3-0357-2397-7
Verlag: Trans Tech Publications

Sonstiges, Englisch, Band Volume 927, 220 Seiten, Format (B × H): 125 mm x 142 mm, Gewicht: 200 g

Reihe: Materials Science Forum

Intensive development of engineering contributes to the emergence of new materials and technologies for their processing. This special issue contains research papers on modern technologies for obtaining and processing materials, additive technologies and technologies of welded joints, computer technologies for engineering tasks in materials science. The book is intended for a wide range of specialists engaged in the development and production of heavy-duty metal structures, as well as students, undergraduates, graduate and postgraduate students of technical colleges and universities.

Autoren/Hrsg.

Chinakhov, Dmitry

Fachgebiete

• Technische Wissenschaften Maschinenbau | Werkstoffkunde Technische Mechanik | Werkstoffkunde
• Technische Wissenschaften Maschinenbau | Werkstoffkunde Produktionstechnik Fertigungstechnik

Inhaltsverzeichnis

TMF Influence on Weld Structure at the Welding of 12X18H9TWelding Incident Mitigation at Mechanical EngineeringThe Structure, Microhardness and Wear Resistance of Coatings Obtained through Non-Vacuum Electron Beam Cladding of Chromium and Titanium Carbides on Low Carbon SteelThe Current State of Application of Ultra- and Nanostructured Powders in Technologies in Welding Technologies (Review)Structure and Crack Resistance of N-A-XTRA-70 Steel Joints Manufactured by Hybrid Laser-Arc WeldingSeparation of Abrasive Materials According to the FormRestoration of Agricultural Machines Surfaces by White Cast Iron with the Formation of Technological Repair UnitsPorous Barriers Efficiency Research under the Compact Elements High - Speed LoadingNumerical Simulation of Thermal Processes in Welding with Pulsed Electrode Wire FeedingMulti-Pass Laser and Hybrid Laser-Arc Narrow-Gap Welding of Steel Butt JointsMaterial Wear Resistace Increase of Tillage Machine Working Tools with Electro-Sparkling Application o Coating LayerMachining of Titanium Alloys with Wave Milling CuttersInfluence of Composition of Binder of Electrodes Coating on Cytotoxicity of Welding AerosolsHow Dynamic Properties of Inverters Influence Electrode Metal Transfer to the Weld Pool, and Change Structural and Phase Composition of Welded Joints Produced via High Alloyed ElectrodesEnergy Parameters of Weld Formation Process in MIG-MAG WeldingEffect of Various Heat Sources on Heating of Contact Tip during Mig/Mag WeldingEffect of TIG-Welding on the Structure and Mechanical Properties of the Pseudo-? Titanium Alloy VT19 Welded JointsEffect of Heat Treatment on the Structure and Properties of Titanium Alloy VT22 Welded Joints Produced by TIG-Welding with Flux-Cored WireDeveloping New Powder Wire for Surfacing Details which Works in the Wear Resistance ConditionsComparison of Two Methods of Cutting Temperature CalculationCorrelation between Properties of Oxide Compounds Formed on Contact Surfaces of Cutting Tools and Cutting Tool Wear ResistanceImprovement of Research Procedures into the Highly Rigid Welded Metal Using Thermal Microscopy FacilitiesInvestigation of Thermal Cycle Effect on Hardening of Deposited High-Speed MetalSuperminiature Eddy-Current Transducers for Studying Steel to Dielectric JunctionsTechnological Improvement of Surfacing of Parts of Hammer Crushers Used in Coke-Chemical IndustryThe Comparison of Thermal Insulation Materials for a Process PipelineSystem for Centralised Collection, Recycling and Removal of Waste Pickling and Galvanic Solutions and SludgeSelection of Complete Recovery of Precious Metals in the Processing of Copper-Nickel Alloys in Hydrometallurgical WayFormation and Utilization of Recyclable Wastes at Engineering EnterpriseThe Development of Technology of Basalt Nanocomposite Coatings Detonation-Gas Spaying on the Disk (?Target?) Basis of Thin Layer Magnetron Spaying Equipment

Über Autor(innen)

Ed. Dr. Dmitry A. Chinakhov