Materials and Processing Technology II

Erscheinungsjahr 2018
ISBN: 978-3-0357-1397-8
Verlag: Trans Tech Publications

Buch, Englisch, 220 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 510 g

Intensive development of engineering contributes to the emergence of new materials and technologies for their processing. This special issue contains research papers on modern technologies for obtaining and processing materials, additive technologies and technologies of welded joints, computer technologies for engineering tasks in materials science. The book is intended for a wide range of specialists engaged in the development and production of heavy-duty metal structures, as well as students, undergraduates, graduate and postgraduate students of technical colleges and universities.

Fachgebiete

• Technische Wissenschaften Maschinenbau | Werkstoffkunde Technische Mechanik | Werkstoffkunde
• Technische Wissenschaften Maschinenbau | Werkstoffkunde Produktionstechnik Fertigungstechnik

Inhaltsverzeichnis

Preface
TMF Influence on Weld Structure at the Welding of 12X18H9T
Welding Incident Mitigation at Mechanical Engineering
The Structure, Microhardness and Wear Resistance of Coatings Obtained through Non-Vacuum Electron Beam Cladding of Chromium and Titanium Carbides on Low Carbon Steel
The Current State of Application of Ultra- and Nanostructured Powders in Technologies in Welding Technologies (Review)
Structure and Crack Resistance of N-A-XTRA-70 Steel Joints Manufactured by Hybrid Laser-Arc Welding
Separation of Abrasive Materials According to the Form
Restoration of Agricultural Machines Surfaces by White Cast Iron with the Formation of Technological Repair Units
Porous Barriers Efficiency Research under the Compact Elements High - Speed Loading
Numerical Simulation of Thermal Processes in Welding with Pulsed Electrode Wire Feeding
Multi-Pass Laser and Hybrid Laser-Arc Narrow-Gap Welding of Steel Butt Joints
Material Wear Resistace Increase of Tillage Machine Working Tools with Electro-Sparkling Application o Coating Layer
Machining of Titanium Alloys with Wave Milling Cutters
Influence of Composition of Binder of Electrodes Coating on Cytotoxicity of Welding Aerosols
How Dynamic Properties of Inverters Influence Electrode Metal Transfer to the Weld Pool, and Change Structural and Phase Composition of Welded Joints Produced via High Alloyed Electrodes
Energy Parameters of Weld Formation Process in MIG-MAG Welding
Effect of Various Heat Sources on Heating of Contact Tip during Mig/Mag Welding
Effect of TIG-Welding on the Structure and Mechanical Properties of the Pseudo-ß Titanium Alloy VT19 Welded Joints
Effect of Heat Treatment on the Structure and Properties of Titanium Alloy VT22 Welded Joints Produced by TIG-Welding with Flux-Cored Wire
Developing New Powder Wire for Surfacing Details which Works in the Wear Resistance Conditions
Comparison of Two Methods of Cutting Temperature Calculation
Correlation between Properties of Oxide Compounds Formed on Contact Surfaces of Cutting Tools and Cutting Tool Wear Resistance
Improvement of Research Procedures into the Highly Rigid Welded Metal Using Thermal Microscopy Facilities
Investigation of Thermal Cycle Effect on Hardening of Deposited High-Speed Metal
Superminiature Eddy-Current Transducers for Studying Steel to Dielectric Junctions
Technological Improvement of Surfacing of Parts of Hammer Crushers Used in Coke-Chemical Industry
The Comparison of Thermal Insulation Materials for a Process Pipeline
System for Centralised Collection, Recycling and Removal of Waste Pickling and Galvanic Solutions and Sludge
Selection of Complete Recovery of Precious Metals in the Processing of Copper-Nickel Alloys in Hydrometallurgical Way
Formation and Utilization of Recyclable Wastes at Engineering Enterprise
The Development of Technology of Basalt Nanocomposite Coatings Detonation-Gas Spaying on the Disk ('Target') Basis of Thin Layer Magnetron Spaying Equipment

Über Autor(innen)

Ed. Dr. Dmitry A. Chinakhov