Buch, Englisch, 554 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 920 g
The aim of conference is to experience exchange between scientists, designers and technologists who work at field of Materials Science and Materials Processing Technologies for Mechanical Engineering.
Buch, Englisch, 554 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 920 g
ISBN: 978-3-03835-522-9
Verlag: Trans Tech Publications
Autoren/Hrsg.
Fachgebiete
Weitere Infos & Material
Preface
Chapter 1: Metal Physics and Mechanics of Deformation Processes
Computer Analysis of Sinking Pass through one and Two Dies
Determination of One-Channel Press Dies Operating Corbels
Testing Criterion Models of Destruction of Materials with Different Rheological Properties under Edge Cutting Machining
The Results Comparasion of Calculation Method and Computer Modeling of Double Curvature Sheet Shells in Stretch Forming Process
Influence of Temperature, Strain Rate, and Sheet Thickness on the Deformation Behaviour of Twin-Roll Cast, Rolled and Heat-Treated AZ31 under Uniaxial Loading
Modeling the Hot Deformation Behavior of 1565ch Aluminum Alloy
Property Oriented Wire Rolling Technology for Mg-Al Alloys
The Parameters of the Stress State in the Operations of Plastic Deformation
Influence of Temperature and Loading Rate on the Forming Limit Behaviour of Twin-Roll Cast, Rolled and Heat-Treated AZ31 as a Function of the Stress State
The Study of Plastic Deformation at High Strain Rates in Upset Forging of Cylinders
Evaluation of Formability of Thin Sheet Metal from Mechanical Properties
Influence of Deformation Conditions on the Microstructure and Formability of Sintered Mg-PSZ Reinforced TRIP-Matrix-Composites
Material Flow in Mg-PSZ Particle Reinforced TRIP-Matrix-Composites due to Hot-Rolling
Bainitic Steels, their Characteristics and Applications
Upgraded Railway Front Searchlight Design Plastic Deformations by its Vibrations with Resonance Frequencies
Residual Stresses Control for Large Scale Open Die Forged Parts
Mathematical Model of Anisotropic Elastoplastic Material
Virtual Material Model with the Given Crystallographic Orientation of the Structure
Isothermal Backward Extrusion of Thick-Walled Anisotropic Pipe Blanks in Mode of Short-Time Creeping
Combined Isothermal Drawing of Axissymmetrical Parts Made out of Anisotropic Materials in Mode of Short-Time Creeping
Technological Modes of Stretching Operation Involving Wall Thinning of Axissymmetric Blanks Made out of Anisotropic Materials
Chapter 2: Advanced and High-Energy Processes in Metal Pressure Working
Development of the Combined Technology of Manufacturing of the Facilitated Constructions of Seal of an Electrocable
Development of Methods and Research on High Voltage Capacitor Welding
Formation of Hard Alloys of Chromium Carbide and Titanium Powder Mixtures by Explosive Pressing
The Wear-Resistance and Antifrictional Properties of Hard Alloys of Chromium Carbide with Titanium Produced by the Explosive Compaction of Powders
Pressing Tubes with Conical-Stepped Needles Computer Simulating
Characteristics of Large Bars Extruding Using Small Extrusion Ratio
Development and Enhancement of Thin-Walled Tube Separation Methods
Determination of Rheological Properties of Titanium Alloys under Conditions of High Strain Rates
Computer Simulation of the Half-Tore Forming Process from a Ring Blank
Stamping of Hemispheric Surface Parts in Die Tool Equipped with Steel Elastic Element
The Forming Process of the Sharply Curved Offsets by the Pushing Method
Directional Thickness Alteration of a Thin-Walled Ring Blank Using Flanging and Forming for the Purpose of Receiving Conical Part
Forming of Small-Diameter Tubes via Pulse-Magnetic Technology
Application of Structural Inheritance Phenomenon at Producing the Al-Mg System Alloys
Research of the Parts Pressing Process Using the Elastic Media Pressure
Chapter 3: Advanced Materials and Nanotechnologies
Nanostructured Aluminum Matrix Composites of Al-10%TiC Obtained In Situ by the SHS Method in the Melt
A Review on In Situ Synthesis of Al/TiC and Al/SiC-Composites
Stress-Corrosion Defects Fatigue Development in Compressor Station Output Gas Pipeline
Fabrication of Al-AlN Nanocomposites
Obtaining Nanopowder Pseudo-Ligatures Al-(SiC+Si3N4) for Modification of Aluminum Alloys
Recovery Technology Features of Aerospace Parts by Layering Synthesis
Metal-Polymer-Metal Laminates for Lightweight Application
Study of Stress Relaxation for 5056 Alloy in Vacuum Conditions
Research of the Microstructure and Mechanical Properties of Copper and CuZn36 Developing during Deformation into the Equal Channel Speed Matrix with High-Intensity Cooling
SHS Metallurgy of NiAl-Based Alloy
A New Method of Metallic Alloys Producing with Interphases, which are Formed Coherent Coupling of Compounds’ Atoms
Effect of Strain on the Anisotropy Coefficient of Sheet Alloys AA2024, Ti-2Al-1Mn, Titanium Grade 2, STEEL X10CrNiTi18-9
Fabrication of Aluminum-Ceramic Composites with TiC-Ni Skeleton by SHS Pressing Method
Study of Possibility of Obtaining Nanopowder Composition of "Aluminum Nitride – Boron Nitride" by Azide SHS Technology
Characterization Analytic Method Specifying the Steel X10CRNITI18-10 Cylinder Surface Layer Quality Hardened by a Traveling Sphere
Influence of 3104 Alloy Microstructure on Sheet Performance in Ironing Aluminum Beverage Cans
Chapter 4: Tools and Machine Parts, Assurance of Materials Quality, Organization of Production
Manufacturing Process Optimization at Enterprises
Constructional Materials Quality Management According to the Scanning Thermal Analyzer
Efficiency Improvement of Metal Lathing by Using of an Evaluation Technique of Assembly Machine Tools Quality
An Industrial and Sociological Research of Consumers Requirements to a Lathing Tool
Enhancement of a Methodology of Assembly Lathing Tools Quality Evaluation
Peculiarities of Quality Ensuring in Parts from Ti-Based Alloy VT6 with Ultrafine-Grained Structure
Structural Strength of Materials as a Factor to Ensure the Quality of Machine Parts
Application of the Method of Performance Evaluation of the Production Process Design Using Associative Design
Improvement of Methodology of Evaluation of Efficiency of the Metallurgical Complex Processes Development
Quality Management of Metal Products Prepared by High-Speed Direct Laser Deposition Technology
The Quality Improvement in Manufacturing “Screw”-Parts Using the DEFORM-3D Software
Development of FMEA Method with the Purpose of Quality Assessment of Can Stock Production
Mathematical Model and Program Development for the Efficient Process Conditions Determination during FeC0.15Cr12Ni2 Steel Diamond Smoothing
Testing of Thin-Walled Tubular Workpieces
Improvement of Technological Process of Multiproduct Production on the Bases of Simulation Modeling of Production Unit
Designing Forging and Die Tooling for the Manufacture of Turbine Engine Compressor Blades in Siemens NX
Multi-Block and Multi-Station Pulse-Magnetic Installations
Pulse-Magnetic Processing of Materials - Development - Problems and Solution Techniques
Problems of Realization of Static-Dynamic Technologies and Ways of their Solution
Actuator from a Material with the High-Temperature Shape Memory Effect and Examples of its Application in Engineering
Design Features of the Small-Scale PMI Power Unit
