Sonstiges, Englisch, Band Volume 684, 554 Seiten, Format (B × H): 125 mm x 142 mm, Gewicht: 200 g
Reihe: Key Engineering Materials
Advanced Materials and Processes of Metalworking
Erscheinungsjahr 2016
ISBN: 978-3-03859-307-2
Verlag: Trans Tech Publications
The aim of conference is to experience exchange between scientists, designers and technologists who work at field of Materials Science and Materials Processing Technologies for Mechanical Engineering.
Sonstiges, Englisch, Band Volume 684, 554 Seiten, Format (B × H): 125 mm x 142 mm, Gewicht: 200 g
Reihe: Key Engineering Materials
ISBN: 978-3-03859-307-2
Verlag: Trans Tech Publications
Autoren/Hrsg.
Fachgebiete
Weitere Infos & Material
Computer Analysis of Sinking Pass through one and Two DiesDetermination of One-Channel Press Dies Operating CorbelsTesting Criterion Models of Destruction of Materials with Different Rheological Properties under Edge Cutting MachiningThe Results Comparasion of Calculation Method and Computer Modeling of Double Curvature Sheet Shells in Stretch Forming ProcessInfluence of Temperature, Strain Rate, and Sheet Thickness on the Deformation Behaviour of Twin-Roll Cast, Rolled and Heat-Treated AZ31 under Uniaxial LoadingModeling the Hot Deformation Behavior of 1565ch Aluminum AlloyProperty Oriented Wire Rolling Technology for Mg-Al AlloysThe Parameters of the Stress State in the Operations of Plastic DeformationInfluence of Temperature and Loading Rate on the Forming Limit Behaviour of Twin-Roll Cast, Rolled and Heat-Treated AZ31 as a Function of the Stress StateThe Study of Plastic Deformation at High Strain Rates in Upset Forging of CylindersEvaluation of Formability of Thin Sheet Metal from Mechanical PropertiesInfluence of Deformation Conditions on the Microstructure and Formability of Sintered Mg-PSZ Reinforced TRIP-Matrix-CompositesMaterial Flow in Mg-PSZ Particle Reinforced TRIP-Matrix-Composites due to Hot-RollingBainitic Steels, their Characteristics and ApplicationsUpgraded Railway Front Searchlight Design Plastic Deformations by its Vibrations with Resonance FrequenciesResidual Stresses Control for Large Scale Open Die Forged PartsMathematical Model of Anisotropic Elastoplastic MaterialVirtual Material Model with the Given Crystallographic Orientation of the StructureIsothermal Backward Extrusion of Thick-Walled Anisotropic Pipe Blanks in Mode of Short-Time CreepingCombined Isothermal Drawing of Axissymmetrical Parts Made out of Anisotropic Materials in Mode of Short-Time CreepingTechnological Modes of Stretching Operation Involving Wall Thinning of Axissymmetric Blanks Made out of Anisotropic MaterialsDevelopment of the Combined Technology of Manufacturing of the Facilitated Constructions of Seal of an ElectrocableDevelopment of Methods and Research on High Voltage Capacitor WeldingFormation of Hard Alloys of Chromium Carbide and Titanium Powder Mixtures by Explosive PressingThe Wear-Resistance and Antifrictional Properties of Hard Alloys of Chromium Carbide with Titanium Produced by the Explosive Compaction of PowdersPressing Tubes with Conical-Stepped Needles Computer SimulatingCharacteristics of Large Bars Extruding Using Small Extrusion RatioDevelopment and Enhancement of Thin-Walled Tube Separation MethodsDetermination of Rheological Properties of Titanium Alloys under Conditions of High Strain RatesComputer Simulation of the Half-Tore Forming Process from a Ring BlankStamping of Hemispheric Surface Parts in Die Tool Equipped with Steel Elastic ElementThe Forming Process of the Sharply Curved Offsets by the Pushing MethodDirectional Thickness Alteration of a Thin-Walled Ring Blank Using Flanging and Forming for the Purpose of Receiving Conical PartForming of Small-Diameter Tubes via Pulse-Magnetic TechnologyApplication of Structural Inheritance Phenomenon at Producing the Al-Mg System AlloysResearch of the Parts Pressing Process Using the Elastic Media PressureNanostructured Aluminum Matrix Composites of Al-10%TiC Obtained In Situ by the SHS Method in the MeltA Review on In Situ Synthesis of Al/TiC and Al/SiC-CompositesStress-Corrosion Defects Fatigue Development in Compressor Station Output Gas PipelineFabrication of Al-AlN NanocompositesObtaining Nanopowder Pseudo-Ligatures Al-(SiC+Si3N4) for Modification of Aluminum AlloysRecovery Technology Features of Aerospace Parts by Layering SynthesisMetal-Polymer-Metal Laminates for Lightweight ApplicationStudy of Stress Relaxation for 5056 Alloy in Vacuum ConditionsResearch of the Microstructure and Mechanical Properties of Copper and CuZn36 Developing during Deformation into the Equal Channel Speed Matrix with High-Intensity CoolingSHS Metallurgy of NiAl-Based AlloyA New Method of Metallic Alloys Producing with Interphases, which are Formed Coherent Coupling of Compounds? AtomsEffect of Strain on the Anisotropy Coefficient of Sheet Alloys AA2024, Ti-2Al-1Mn, Titanium Grade 2, STEEL X10CrNiTi18-9Fabrication of Aluminum-Ceramic Composites with TiC-Ni Skeleton by SHS Pressing MethodStudy of Possibility of Obtaining Nanopowder Composition of "Aluminum Nitride ? Boron Nitride" by Azide SHS TechnologyCharacterization Analytic Method Specifying the Steel X10CRNITI18-10 Cylinder Surface Layer Quality Hardened by a Traveling SphereInfluence of 3104 Alloy Microstructure on Sheet Performance in Ironing Aluminum Beverage CansManufacturing Process Optimization at EnterprisesConstructional Materials Quality Management According to the Scanning Thermal AnalyzerEfficiency Improvement of Metal Lathing by Using of an Evaluation Technique of Assembly Machine Tools QualityAn Industrial and Sociological Research of Consumers Requirements to a Lathing ToolEnhancement of a Methodology of Assembly Lathing Tools Quality EvaluationPeculiarities of Quality Ensuring in Parts from Ti-Based Alloy VT6 with Ultrafine-Grained StructureStructural Strength of Materials as a Factor to Ensure the Quality of Machine PartsApplication of the Method of Performance Evaluation of the Production Process Design Using Associative DesignImprovement of Methodology of Evaluation of Efficiency of the Metallurgical Complex Processes DevelopmentQuality Management of Metal Products Prepared by High-Speed Direct Laser Deposition TechnologyThe Quality Improvement in Manufacturing ?Screw?-Parts Using the DEFORM-3D SoftwareDevelopment of FMEA Method with the Purpose of Quality Assessment of Can Stock ProductionMathematical Model and Program Development for the Efficient Process Conditions Determination during FeC0.15Cr12Ni2 Steel Diamond SmoothingTesting of Thin-Walled Tubular WorkpiecesImprovement of Technological Process of Multiproduct Production on the Bases of Simulation Modeling of Production UnitDesigning Forging and Die Tooling for the Manufacture of Turbine Engine Compressor Blades in Siemens NXMulti-Block and Multi-Station Pulse-Magnetic InstallationsPulse-Magnetic Processing of Materials - Development - Problems and Solution TechniquesProblems of Realization of Static-Dynamic Technologies and Ways of their SolutionActuator from a Material with the High-Temperature Shape Memory Effect and Examples of its Application in EngineeringDesign Features of the Small-Scale PMI Power Unit
