Materials Science and Technology IX

MSAT-9
Erscheinungsjahr 2017
ISBN: 978-3-0357-1082-3
Verlag: Trans Tech Publications

Buch, Englisch, 860 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 1570 g

The book is collected from papers that were submitted on the 9th International Conference on Materials Science and Technology (MSAT-9, December 14-15, 2016, Bangkok, Thailand) and is devoted to the modern issues of research and development in area of materials and materials processing technologies. We hope this collection should be useful for wide range of specialists from various branches of engineering activity.

Autoren/Hrsg.

Pinwanich, Peerapong

Soisungval, Akrapol

Fachgebiete

• Technische Wissenschaften Maschinenbau | Werkstoffkunde Technische Mechanik | Werkstoffkunde

Inhaltsverzeichnis

Preface, Committees, Sponsors and Organizers
Chapter 1: Metals, Alloys and Intermetallic Compounds
The Thermal-Aging Effect on the Microstructure Evolution and Shear Strength of the Sn-Rich Au-Sn Soldering between Altic and Si Substrate in Microelectronics
Effect of Cooling Rate on the Microstructural and Mechanical Properties of Sn-0.3Ag-0.7Cu-0.05Ni Solder Alloy
Effect of Si Content on Mechanical Properties of Ti-Si-N Ternary Alloys Prepared by Spark Plasma Sintering
Properties of Sintered Bronze-Graphite Containing Natural Anhydrite
Properties of Sintered Bronze-Graphite Containing Calcium Sulfate Derived from Waste Plaster Molds
The Effect of Bottom Ash Additions on the Properties of Sintered Bronze-Graphite Composites
Effect of Compaction Pressure and Sintering Time on the Properties of Sintered Cu-10Sn Bronze
Modification of Microstructure and Tensile Property of Sintered Fe-Cr-Mo-C Steel by Nickel Addition
Microstructure, Hardness and Wear Properties of Sintered Fe-Mo-Si-C Steels with Spheroidal Graphite Iron/Compacted Graphite Iron-Like
Effect of Aluminum Addition on AlxCoFeMnNiZn Multi-Component Production
Mechanical Properties of As-Exposed Al-SiCp Composite Fabricated by Powder Injection Moulding
Chapter 2: Corrosion, Coatings, Surface Engineering and Heat Treatment
Hardfacing of 3.5% Chromium Cast Steel by Flux Cored Wire Arc Welding Process
Effect of Impingement Angle on Erosion Resistance of HVOF Sprayed WC-10Co-4Cr Coating on CA6NM Steel
Structural Characterization of Reactive DC Magnetron Co-Sputtered Nanocrystalline CrAlN Thin Film
Solid Particle Erosion Resistance of Thermal Sprayed Nickel Alloy Coating
Sintered Metal Microstructure Influenced by Deep Rolling and Carburizing Processes
Corrosion Behavior of Al-Zn-In Sacrificial Anode Alloys Produced by Conventional Casting and Semi-Solid Metal Casting Processes
Development of Pitting Corrosion Monitoring Device under Sodium Chloride Droplet by Means of Wet-Dry Cyclic Method
Improvement of Structural, Morphological and Mechanical Properties of CrNx Sputtered Thin Films by Vacuum Annealing Process
Study of Microstructure and Corrosion Resistance of Zinc Electrodeposits before and after Black Chromating
Factors Affecting on the Corrosion Resistance of Electroless Ni-Zn-P Coated Steel
Effect of Post-Curing Temperature and Mechanical Surface Treatment on Shear-Bond Strength of Asbestos-Free Brake Pad
Effects of Air Exposure Time and Annealing Temperature on Superhydrophobic Surface of Titanium Dioxide Films
Chapter 3: Processing Technologies and Equipments
Meta-Heuristics for Engineering Optimisation - Applications to Metal Forming Processes
Development of a Regression Model of Stk50Eu for a Hydrocyclone
Development and Characterizations of a Projection Stereolithography
Formability Analysis of Fukui Stretch-Drawing and Square Cup Drawing Using Strain and Stress Based Forming Limit Curves
Effect of Feed-Flow Rate in a Solid-Liquid Hydrocyclone Based on Total Solid Recovery Equation
Bending Limit Curves in Sheet Metal Bending Evaluation
Fastenerless-Riveting Utilizing Friction Stir Forming for Dissimilar Materials Joining
Chapter 4: Advanced Technologies for Materials Testing and Observation
X-Ray Diffraction Analysis of ZnO Particles Prepared by Microwave Plasma
Influence of Scanning Parameters on X-Ray Diffraction Peaks of Copper
The Investigation of Ultrasonic Energy Attenuation in AISI 316 Stainless Steel Weld Joint
Stress Measurement in Carbon Steel by Magnetic Barkhausen Noise Technique
Chapter 5: Polymers and Composites
Influence of Molecular Weight on the Non-Isothermal Melt Crystallization of Biodegradable Poly(D-Lactide)
Gelatin Films and its Pregelatinized Starch Blends: Effect of Plasticizers
Medicated Pressure Sensitive Adhesive Patches from STR-5L Block Rubber: Effect of Preparation Process
Effect of Calcium Carbonate on Crystallization Behavior and Morphology of Poly(3-Hydroxybutyrate-co-3-Hydroxyvalerate)
Simulation of Irradiation-Based Processing System for Natural Rubber Vulcanization
The Smart Blending for Multilayer Structure of PLA/EVOH
Morphology and Properties of Polyoxymethylene/Polypropylene/Microcrystalline Cellulose Composites
Effect of Synthesized Ag Nanoparticles by Using the Different Amounts of Polyvinylpyrrolidone for Ag-Natural Rubber Hybrid Sheets and their Antibacterial Properties
Physical and Mechanical Properties of Wood Plastic Composites from Teak Wood Sawdust and High Density Polyethylene (HDPE)
Effect of Poly(D-Lactic Acid)-co-Polyethylene Glycol on the Crystallization of Poly(L-Lactic Acid)
Effect of Octenyl Succinate Starch on Properties of Tapioca Thermoplastic Starch Blends
Preparation of TiO2/WO3 Composite Nanofibers by Electrospinning
Effect of Poly(Hexamethylene Succinamide) on Crystallization of Poly(L-Lactic Acid)
Mechanical Behavior of Polystyrene-Grafted Natural Rubber/Natural Rubber Blend: Effect of Polystyrene Grafting Percentage
Degradation of Silica-Reinforced Natural Rubber by UV Radiation and Humidity in Soil
Degradation Test of Natural Rubber/Chitosan Composite
Low Haze and Antifog Performance of 2-Layer Poly(Lactic Acid) Based Films
Influence of Pyrolytic Carbon Black Prepared from Waste Tires on Mechanical Properties of Natural Rubber Vulcanizates
Mechanical and Thermal Properties of PLA Melt Blended with High Molecular Weight PEG Modified with Peroxide and Organo-Clay
Poly(Lactic Acid)-Polybutylene Succinate-Activated Carbon Composite Foams
Chapter 6: Ceramics and Functional Metal Oxides
Development of Water Assisted Solid State Reaction for the Ceramic Materials
Slip Degassing to Improve the Properties of Slip Cast and Reaction Bonded Si3N4
Fabrication of Low Cost Membrane from Anodic Aluminum Oxide
Synthesis of Nanocrystalline Cobalt Ferrite by the Sonochemical Method in Highly Basic Aqueous Solution
The Effect of Zirconium Oxide on Properties and Crystallization of Soda-Lime Silicate Glass
Structure, Magnetic Property and Energy Band Gap of Fe-Doped NiO Nanoparticles Prepared by Co-Precipitation Method
Piezoelectric and Ferroelectric Properties of KNbO3 Added Bi0.5Na0.5TiO3 Ceramics
Chemical Composition-Microstructure-Dielectric Constant Relations of Mg-Doped Calcium Titanate Synthesized by Solid State Reaction Technique
Development of Glass-Ceramics from Soda Lime Silica Glass Waste by Direct Sintering Method for Opal Imitation
Effects of Aluminium Contents and Consolidation Techniques on Chemical Composition, Microstructure and Dielectric Properties of Strontium Titanate
Influence of Temperature and Alkaline Activation for Synthesis Zeolite A from Natural Kaolin
Effects of Ball Milling on the Properties of (Ba1-xCax)(Ti0.92Sn0.08)O3 Lead-Free Ceramics
Chapter 7: Materials and Technologies for Electronics and in Energy Production
r-GO/MWCNTs Nanocomposite Film as Electrode Material for Supercapacitor
Pre-Immobilization of Anaerobic Mixed Culture on Electrode of the Upflow Bio-Filter Circuit Microbial Fuel Cell
The Study of Crystallization of Polyfluorene and Fullerene Derivatives in Semiconducting Layer of Organic Solar Cells
Two-Stage Combustion Burner Using Used Engine Oil as Fuel
Pelletization of Iron Oxide Based Sorbents for Hydrogen Sulfide Removal
BaO-Al2O3-SiO2-B2O3 Glass-Ceramic SOFCs Sealant: Effect of ZnO Additive
Microwave-Assisted Preparation of Sodium Silicate as Biodiesel Catalyst from Rice Husk Ash
Characterisation of NiO-YSZ Porous Anode-Support for Solid Oxide Fuel Cells Fabricated by Ceramic Injection Moulding
Process Optimization and Characterization of YSZ Thin Film Electrolyte on Anode Substrate Prepared by Electrophoretic Deposition Technique
The Effect of Calcium-Based Salt on Hydrothermal Carbonization of Corncob
Influence of Bi2O3 on Crystalline Phase Content and Thermal Properties of A°kermanite and Diopside Based Glass-Ceramic Sealant for SOFCs
Synthesis of Ternary Semiconductor Silver Bismuth Telluride by Chemical Bath Deposition
Zeolite Supported Bimetallic Catalyst System: The Effect of Metal Loading for Catalytic Pyrolysis of Jatropha Residue
Charged Iridium(III) Complexes with Varied Side Chain Length in Organic Light Emitting Diodes
Effects of Buffer Layer Growth Temperature on Micro-Structures in the Cubic GaN Films Grown on GaAs (001) Substrates by MOVPE
Effect of Silica Base Catalyst on Transformation of Methanol to Hydrocarbon
Chapter 8: Building Materials
Investigation of Physical, Mechanical and Thermal Properties of Building Wall Materials
Geopolymerization as Cold-Consolidation Techniques for Hazardous and Non-Hazardous Wastes
Influence of Portland Cement on Physical, Mechanical and Thermal Properties of Cellular Lightweight Concrete
The Study on Physical and Thermal Properties of Geopolymer Pastes
Optimum Partial Replacement of Cement by Nanosilica, Microsilica and Rice Husk Ash for Mass Production of Concrete
Effect of Calcium Carbonate on Compressive Strength and Physical Properties of Alkali-Activated Lightweight Concrete
Use of Waste Glass as a Reinforce Material in Calcined-Kaolin Based Geopolymer
Effects of Aluminum Concentrations on Microstructure and Compressive Strength of Porous Concrete
The Mechanical Properties Study of Waste Bakelite Aggregate Concrete
Chapter 9: Materials for Biomedical Application

In Vivo Testing of Sericin-Polyurethane Nanofiber Mats for Wound Healing in Rats
Fluoride Recharge Ability of Resin-Based Pit and Fissure Sealant with Synthesized Mesoporous Silica Filler
Comparison of the Release of Aloe vera Extracts from Poly(Vinyl Alcohol) Electrospun Fibers and Hydrogel Films for Wound Healing Applications
Effect of Process Parameters on Biomimetic Deposition of Calcium Phosphate on 3D Printed Hydroxyapatite
A Preliminary Study of the In Vitro Biocompatibility Testing of Silk Fibroin/Alpha Tricalcium Phosphate Composite Scaffolds for Bone Tissue Engineering
Effect of M-Type Hexaferrites on Mechanical and Magnetic Properties of Hydroxyapatite Ceramics
Synthesis and Characterization of Cerium- and Lanthanum Containing Bioactive Glass
Effect of Solids Loadings, Sintering Temperatures and Sintering Periods on Microstructure of Hydroxyapatite
Effect of Bleaching on Color Change of Stained Resin Composites
PMMA Demonstrated Higher Elastic Modulus and Nanohardness Compared with Polyamide Denture Base Materials
Flexural Strength and Cytotoxicity of ZCC, a Resin Modified Zinc-Calcium Liner Prototype
The Effect of Thermoforming on Tear Strength of Ethylene Vinyl Acetate Mouthguard Material in Various Thicknesses
The Use of Three Dimensional Printed Hydroxyapatite Granules in Alveolar Ridge Preservation
Chapter 10: Materials and Technologies for Waste Recycling and Environmental Engineering
Preparation of Activated Carbon from Sugarcane Bagasse Waste for the Adsorption Equilibrium and Kinetics of Basic Dye
Modified Soil Compositions for Removal of Acetaminophen from Wastewater
Determination of Tannin in Coffee Pulp Using Experimental and Theoritical Approches
Exploitation of Ag3PO4 Impregnated Alginate Beads for the Photocatalytic Degradation of Dye Solution under Sunlight Irradiation
Development of Specific Surface Area in Carbon Material Prepared from Cassava Tuber Char Using a Chemical Activation Assisted Sonochemical Process
Performance Photocatalytic Degradation of Methomyl onto Composite Graphene Oxide/Bismuth Vanadate (GO/BiVO4) Nanoparticle
The Photocatalytic Degradation of Methylene Blue Using Bismuth Vanadate (Bi2VO5.5) Powder
Adsorption of Reactive Dyes Red 195, Blue 222, and Yellow 145 in Solution with Polyaniline-Chitosan Membrane Using Batch Reactor
Adsorption of Reactive Dye (RB 222) in Solution onto Chitosan-Rice Husk Ash Composite Beads Cross-Linked with Glutaraldehyde
On the Application of Electrocoagulation/Flotation (ECF) Technique for Cationic Dye Removals Using Aluminium Electrode and Sodium Dodecyl Sulfate (SDS)
Fabrication Study of Hydrophobic Polyurethane Sponge for Oil Absorption Application
Preparation, Characterization and Photocatalytic Properties of Rubber-TiO2-rGO Composite Sheets for Dye Decomposition in Wastewater
The Effect of Carboxymethyl Cellulose from Various Agriculture Wastes on the Viscosity and Physical Properties of Low Concentration Solution of Surfactant
Adsorptive Properties of Fly Ash Zeolite Synthesized via Microwave and Ultrasonic Pretreatments
Using ZnO Nanorods Coated Porous Ceramic Monolith to Remove Arsenic from Groundwater
Removal of Arsenic from Groundwater Using Nano-Metal Oxide Adsorbents
Synthesis of Carbon Nanoparticles from Used Motor Oil and Benzene via Solution Plasma Process
Development of Oil Palm Empty Fruit Bunch Fiber Reinforced Epoxy Composites for Bumper Beam in Automobile
Improvement of Compressive Strength of Soil by Using Jute Fiber Waste
Assessment of Hydrophilic Biochar Effect on Sandy Soil Water Retention
Photo-Oxidative Degradation Polyethylene Containing Titanium Dioxide and Poly(Ethylene Oxide)
Photocatalytic Activity of Cu-Doped Cerium Dioxide Nanoparticles
Synthesis and Photocatalytic Activity of Visible-Light Responsive BiOBr/GO Composites
Comparison Study of Photocatalytic Activity of Titanium-Rich Materials Derived from Natural Minerals Ores Using Acidic Leaching
Photocatalytic Degradation Study of Titania Sol-Gel Coated on Commercial Unglazed Ceramic Tiles
Photocatalytic Comparative Study of TiO2, ZnO, Ag-G-ZnO and Ag-G-TiO2 Nanocomposite Films

Über Autor(innen)

Eds. Peerapong Pinwanich and Akrapol Soisungval