Buch, Englisch, 736 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 1360 g
Buch, Englisch, 736 Seiten, Format (B × H): 170 mm x 240 mm, Gewicht: 1360 g
ISBN: 978-3-0357-1024-3
Verlag: Trans Tech Publications
Autoren/Hrsg.
Fachgebiete
Weitere Infos & Material
Preface, Committees
Chapter 1: Plenary Keynote
Advances in Constitutive Modeling of Plasticity for Forming Applications
Modelling of Instability and Fracture Effects in the Sheet Metal Forming Based on an Extended X-FLC Concept
Towards a Better Understanding of the Ratcheting Phenomenon
Strain Gradient Plasticity: An Application to Plastic Flow Localization Analysis
Plastic Limit Analysis of Piping with Local Wall-Thinning under Elevated Temperature
Chapter 2: Recent Progress in Impact and Dynamic Plasticity
Investigation on Micro-Tensile Test System Platform Used for Test of the Weld
An Experimental Evaluation of Energy Absorption of TRIP Steel by Small Punch Test
A Computational Investigation on Small Punch Test for Evaluating Fracture Toughness of TRIP Steel at Higher Deformation Rate
A Measurement of Volume Resistivity in Fe-Based Shape Memory Alloy under Tensile Deformation and its Evaluation of Strain Rate Sensitivity
A Study on Tensile Deformation Behavior in Fe-Based Shape Memory Alloy by Rate Sensitive Transformation Kinetics Model
Comparative Research on the Crushing Behaviour of Aluminium Sheet Wrapped Square Carbon Fibre Reinforced Plastic (CFRP) Tubes
Frangibility Study of Natural Fiber Reinforced Composite Laminates
Crashworthiness Study of Composite Fuselage Section
An Experimental Study on Axial Joint Strength Made of Fe-28Mn-6Si-5Cr Shape Memory Alloy at Various Deformation Speeds
The Saturated Impulse for Fully Clamped Square Plates Subjected to Linear-Decay Pressure Pulse
Seismic Performance of a Concrete Highway Tunnel under Earthquake Sequence Using a Concrete Damage Plasticity Model
Probing Temperature-Dependent Viscoelastic Properties of Glassy Materials Using Impact Induced Vibration - Theory and Experiments
Low Velocity Impact Behavior of SiC/PU/GFRP Laminates
Low Velocity Impact Response of Composite/Sandwich Structures
Rate-Dependent Material Parameters of the Combined Isotropic/Kinematic Hardening Model for the TRIP980 Steel Sheet
Characterization of Hardening Behavior at Ultra-High Strain Rate, Large Strain, and High Temperature
Large Deformation Modeling of a Re-Entrant Honeycomb under Tensile Load
Large Deflection Response of Rectangular Metal Sandwich Plates with Functionally Graded Foam Core Subjected to Blast Loading
Numerical Study of the Effects of Strain Rate and Cell Geometry on Dynamic Behavior of Axial Crushing Honeycomb
A New Design of Energy Absorbing Bolt
Impact Combined Shear-Compression Testing of Honeycombs Using a Rotatable Hopkinson Bar
Chapter 3: Modeling and Simulation of Multiscale Plasticity for Various Materials
The Evolution of the {110} and {236} Recrystallization Textures in Cu Alloys and High Mn Austenitic Steels with the Brass Rolling Texture
Crystal Plasticity Analysis of Change in Active Slip Systems of a-Phase of Ti-6Al-4V Alloy under Cyclic Loading
Dislocation Dynamics Simulation of Interaction between Prismatic Dislocation Loops and Voids in Irradiated Thin Films
Anisotropic Elastic Field of 3D Prismatic Dislocation Loops in Bounded and Voided Single Crystal Films
Measurement of Bauschinger Effect in Ultrafine-Grained A1070 Aluminum Rods
A Simulation of Ferroelastic Phase Formation by Using Phase Field Model
Quantitative Evaluation of Deformation Twinning Behavior in Polycrystalline Pure Magnesium
Subsequent Yield Behavior of Hexagonal Metal with Rolling Texture
On the Role of Grains in Plastic Deformation and Low Cycle Fatigue of Polycrystalline Metal
High Temperature Deformation of Cast ZW11 Magnesium Alloy with Very Large Grain Size
MD Analysis of Effect of Relative Humidity on Molecular Chain’s Network Structure of PEM
Multiscale Simulation of Dynamic Recrystallization for a-Mg Phase in Mg/LPSO Alloys Based on Multi-Phase-Field and Dislocation-Based Crystal Plasticity Model
Macroscopic Yield Function Predicted by Crystal Plasticity Simulation on Ultrafine-Grained Aluminum
Numerical Biaxial Tensile Test of Aluminum Alloy Sheets Using Crystal Plasticity Model Implemented in Commercial FEM Software
Development of Simulation Technology for Production of Porous Polymeric Membranes
Crystal Plasticity Analysis of Mechanical Response in Two Phase Alloys with Dispersion of Fine Particles
Chapter 4: Cyclic Plasticity
Thermo-Mechanical Cyclic Plastic Behavior of 304 Stainless Steel at Large Temperature Ranges
Estimation of Residual Stress Change due to Cyclic Loading by Classical Elastoplasticity Model and Subloading Surface Model
Application of Subloading Surface Model to Heat Treatment Simulation Based on Explicit Finite Element Method
Evaluation of the Stress Distribution by the Stepped Load Indentation Test with Constant Depth
Biaxial Ratchetting Deformation of Solders Considering Halt Conditions
Estimation of Plastic and Creep Strain Development of SAC Solder under Cyclic Loading by Using Stepped Ramp Waves
An Improved Thermo-Ratcheting Boundary of Pressure Pipeline
Study of Micro Deformation of Austenitic-Ferrite Duplex Stainless Steel by Nanoindentation Method
Effect of the Non-Associativity of Plasticity Model on the Cyclic Behavior of Geomaterials
Thermo-Elasto-Plastic Analysis of Pearlitic Transformation Plasticity under Combined Bending-Tensile Loading
Fatigue of Extruded 2017A Aluminum Alloy Subjected to Non-Proportional Loading Paths
Elastic and Plastic Analysis of O-Ring Seal for Reactor Pressure Vessel
Calculation Strategy for the Determination of Plasticity Correction Factors
Description of Closure of Cyclic Stress-Strain Loop and Ratcheting Based on Y-U Model
Chapter 5: Strength of Advanced Materials
On the Choice of the Power Law Flow Rule and its Consequences in Crystal Plasticity
Evaluation of Very High Cycle Fatigue Properties of ß-Titanium Alloy by Using an Ultrasonic Tensile-Compressive Fatigue Testing Machine
Relaxation Oscillation in the Viscous Flow of Borosilicate Glass
Deformation Properties of 3D Printed Shape Memory Polymer
Failure Criteria of Adhesive Joints between Aluminum Circular Pipes under Multiaxial Stress State
Improvement of Corrosion Fatigue Strength for TiNi Shape Memory Alloy
Experimental Study and Finite Element Simulation of Bending Fretting Fatigue for Tempered 42CrMo Steel
First Principles Calculations of Stress-Induced Structural Changes of Supercooled Borosilicate Glass
Super-Elastic Behavior Analysis of Shape Memory Alloy Vascular Stent
Elasto-Viscoplastic Analysis of Slanting-Weft Woven Fabric Composites Based on Homogenization Theory
Effects of Blowing Ar on Inclusion and Properties of AZ61 Magnesium Alloy
Temperature Dependent Plastic Deformation Behavior of AZ31 Magnesium Alloy in Uniaxial and Biaxial Compressions
Effects of Two Scaling Exponents on Swelling-Induced Softening of Elastomers under Equibiaxial and Planar Extensions
Two-Scale Analysis of Thermal Behavior of CFRP Laminates Based on a Thermoelastoviscoplastic Homogenization Theory
Evaluation of Micro/Meso/Macro Thermal Properties of Plain-Woven Laminates
Atomistic-Level Simulation of Deformation in Polycarbonate
Atomistic Model Analysis of Deformation of Carbon Nanotubes under Axial Compression
Computational Simulation of Scale-Dependent Non-Uniform Deformation Behavior of Polymer Foam
Chapter 6: Damage, Localization and Fracture of Engineering Materials
Effects of Non-Associated Flow Rule on AHSS Shear Fracture
Influence of Geometrical Imperfection on Failure Mode of DP780 Steel Utilizing Damage Models Embedded RVE Technique
Characterizing Fracture Development in Ti-Alloy with I-Type Cracks Using Acoustic Emission and Thermal Infrared Imaging
Application of Uncoupled Damage Models to Predict Ductile Fracture in Sheet Metal Blanking
Anisotropic Damage Evolution for Perforated Sheet under Tensile Deformation
Bending Behavior to Fracture of an Aluminium Alloy Involving Pre-Strain
Effect of Lattice Rotation on Hardening Behavior of HCP Metals
Chapter 7: Optimization and Inverse Problems in Nonlinear Mechanics
A New Algorithm of the Boundary Restraining Force for One-Step Inverse Analysis
The Refinement Algorithm of Blank Outline Based on One-Step Inverse Analysis
An Adaptive Triangle Mesh Generation for One Step Inverse Analysis
Effect of Optimisation Parameters in Topology Optimisation
Chapter 8: Progress in Processing and Forming of Metal Materials
Warping Behavior of Thin Strip with Single-Drive Rolling
Influence of Dog-Bone Width on End Profile in Plan View Pattern Control Method for Plate Rolling
Transient Thermal Analysis of Cold Strip Rolling Considering Rough Surface Contacts
The Numerical Simulation of Multi-Stage Sheet Metal Forming Based on Modified Yoshida-Uemori Hardening Model
Numerical Investigation on Mini Internal Gear Forging Process
Springback Analysis of Aluminum Alloy Sheet Metals by Yoshida-Uemori Model
Wear Mechanism and Ability for Recovery of Tool Steel on Blanking Die Process
Investigation on Wrinkling Deformation in Multi-Pass Incremental Sheet Forming Process
An Experimental and Numerical Study on Forming Force, Fracture Behavior, and Strain States in Two Point Incremental Forming Process
Effect of Material Anisotropies of Hot-Rolled High-Strength Steel Sheet on Localized Deformation Behavior in Hole Expansion - Part-I Experimental Consideration to Circular and Oval Hole
Effect of Material Anisotropies of Hot-Rolled High-Strength Steel Sheet on Localized Deformation Behavior in Hole Expansion - Part-II Simulation and Evaluation of Anisotropic Yield Function
Development of a Rubber Diaphragm Forming Simulation System Based on ABAQUS
Improvement of Shape Accuracy in Press-Formed Parts of High-Strength Steel by Springback-Root-Cause Analysis
Study of Large-Expansion-Ratio Tube Hydroforming with Movable Dies
Research on Stability of Panel Ultrasonic Peening Forming
Asymmetric-Shaped Bending of Adhesively Bonded Sheet Metals
Study on Magnesium Alloy Thin Sheet by Symmetric Rolling and Asymmetric Rolling Process
Pulsed Laser Surface Treatment for Improvement of Machinability
Residual Stress Analysis Considering Phase Transformation and Transformation Plasticity for Heat-Treated Large Size Shaft
A Yield Function for Anisotropic Sheet Material Described by 3rd-Degree Spline Curve and its Applications
Elastic Modulus Model Based on Dislocation Density and its Application on Aluminum Alloy 5052
Friction Stir Forming of Aluminum Alloy Gear-Racks
Effect of Stress Relaxation on Springback of Steel Sheet in Warm Forming
Determination of the Anisotropic Hardening of Sheet Metals at Large Strain from Stretch Bending Test
Simple Springback Cause Analysis Using Measured Shapes of Dies and Pressed Part
On the Scale Dependence of Micro Hydromechanical Deep Drawing
Equi-Plastic Work Locus of 5000 Series Aluminum Alloy Sheet at Warm Temperature
Optimum Design of Si-Cr Alloy Springs for Seismic Vibration Isolator
Effects of Aging Process in Hot Forming with Synchronous Cooling on Properties of AA2024
